Epson L6191 Instruction Manual

Start Here
12 When the ink confirmation message appears on the LCD
screen, select Done to start charging the ink. Ink charging
takes approximately 10 minutes. A message appears
when ink charging is complete. Press the OK button to
continue.
Caution: Do not turn off the product, raise the scanner unit, or
load paper while the product is charging or you’ll waste ink.
Note: After some ink is used for charging, the rest is available
for printing.
13 To complete filling the ink tanks, repeat steps 1 through 6
using the remaining ink in the bottles.
Note: Replace the bottle cap before disposing of the bottles.
14 Close the ink tank cover and scanner unit.
15 Select Next and follow the on-screen instructions to reset
the ink levels.
16 Follow the on-screen instructions to adjust the print
quality. Press the OK button to continue.
Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
3Load paper
See the online User’s Guide for information about loading
capacity and available paper types and sizes.
1 Make sure the product is not charging, and then open
the front of the paper cassette and pull out the paper
cassette.
2 Slide the side edge guides all the way out.
Read these instructions before using your product.
The illustrations show the L6191, but the steps are the same for
all models, unless otherwise specified.
1Unpack
Power cable USB cable
Telephone cord
(L6191 only)
Note: Do not open the ink bottles until you are ready to fill the ink
tanks. The ink bottles are vacuum packed to maintain reliability.
1 Remove all protective materials from the product.
2 Lift up the scanner unit. Remove all protective materials
from inside the product.
Caution: Do not touch the flat white cable or the ink tubes and
their translucent cover.
2Fill ink tanks
Note: This product requires careful handling of ink. If ink spills, wipe
it off immediately with a damp towel to avoid permanent stains. If ink
gets on your clothes or belongings, it may not come off.
Warning: Keep the ink bottles out of the reach of children and do not
drink the ink.
1 Open the ink tank cover, then open the cap for the ink
tank you are going to fill.
2 Unpack one of the ink bottles. Hold the ink bottle upright
and slowly turn the bottle cap to remove it.
Caution: Do not shake or squeeze the ink bottles. Do not touch
the top of the ink bottle after its cap is removed.
3 Position the top of the ink bottle along the slot in front of
the filling port, then slowly stand the bottle up to insert it.
Note: Refer to the color-coded sticker to identify the color of
each tank. Do not force the bottles into position; they are keyed
for each color.
4 Wait for the ink to fill the tank. Do not squeeze the bottle.
Ink flows into the tank and stops automatically when the
ink is filled to the upper line.
Note: If ink does not flow from the bottle, lift and reinsert the
bottle.
5 When the ink tank is full, remove the ink bottle and
securely close the ink tank cap. Place the remaining ink
aside; you will need it later.
Note: Replace the bottle cap and tighten it.
6 Repeat the previous steps for the other colors.
7 Close the ink tank cover and then the scanner unit.
8 Connect the power cord to the back of the product and to
an electrical outlet.
Caution: Do not connect to your computer yet.
9 Raise the control panel, then press the power button to
turn on the product.
Note: If an error message appears, turn off the product and
check that no protective material has been left inside the product.
10 L6171: Press or to select your language on the LCD
screen, then press the OK button.
L6191: Select your language, country, and time.
Follow steps 11 and 12 to continue ink charging.
Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
11 When the message to see the Start Here sheet appears
on the LCD screen:
L6171: Press the OK button, then press and hold the
help button for 3 seconds.
L6191: Press and hold the help button for 3 seconds.
L6171/L6191

Start Here
12 When the ink confirmation message appears on the LCD
screen, select Done to start charging the ink. Ink charging
takes approximately 10 minutes. A message appears
when ink charging is complete. Press the OK button to
continue.
Caution: Do not turn off the product, raise the scanner unit, or
load paper while the product is charging or you’ll waste ink.
Note: After some ink is used for charging, the rest is available
for printing.
13 To complete filling the ink tanks, repeat steps 1 through 6
using the remaining ink in the bottles.
Note: Replace the bottle cap before disposing of the bottles.
14 Close the ink tank cover and scanner unit.
15 Select Next and follow the on-screen instructions to reset
the ink levels.
16 Follow the on-screen instructions to adjust the print
quality. Press the OK button to continue.
Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
3Load paper
See the online User’s Guide for information about loading
capacity and available paper types and sizes.
1 Make sure the product is not charging, and then open
the front of the paper cassette and pull out the paper
cassette.
2 Slide the side edge guides all the way out.
Read these instructions before using your product.
The illustrations show the L6191, but the steps are the same for
all models, unless otherwise specified.
1Unpack
Power cable USB cable
Telephone cord
(L6191 only)
Note: Do not open the ink bottles until you are ready to fill the ink
tanks. The ink bottles are vacuum packed to maintain reliability.
1 Remove all protective materials from the product.
2 Lift up the scanner unit. Remove all protective materials
from inside the product.
Caution: Do not touch the flat white cable or the ink tubes and
their translucent cover.
2Fill ink tanks
Note: This product requires careful handling of ink. If ink spills, wipe
it off immediately with a damp towel to avoid permanent stains. If ink
gets on your clothes or belongings, it may not come off.
Warning: Keep the ink bottles out of the reach of children and do not
drink the ink.
1 Open the ink tank cover, then open the cap for the ink
tank you are going to fill.
2 Unpack one of the ink bottles. Hold the ink bottle upright
and slowly turn the bottle cap to remove it.
Caution: Do not shake or squeeze the ink bottles. Do not touch
the top of the ink bottle after its cap is removed.
3 Position the top of the ink bottle along the slot in front of
the filling port, then slowly stand the bottle up to insert it.
Note: Refer to the color-coded sticker to identify the color of
each tank. Do not force the bottles into position; they are keyed
for each color.
4 Wait for the ink to fill the tank. Do not squeeze the bottle.
Ink flows into the tank and stops automatically when the
ink is filled to the upper line.
Note: If ink does not flow from the bottle, lift and reinsert the
bottle.
5 When the ink tank is full, remove the ink bottle and
securely close the ink tank cap. Place the remaining ink
aside; you will need it later.
Note: Replace the bottle cap and tighten it.
6 Repeat the previous steps for the other colors.
7 Close the ink tank cover and then the scanner unit.
8 Connect the power cord to the back of the product and to
an electrical outlet.
Caution: Do not connect to your computer yet.
9 Raise the control panel, then press the power button to
turn on the product.
Note: If an error message appears, turn off the product and
check that no protective material has been left inside the product.
10 L6171: Press or to select your language on the LCD
screen, then press the OK button.
L6191: Select your language, country, and time.
Follow steps 11 and 12 to continue ink charging.
Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
11 When the message to see the Start Here sheet appears
on the LCD screen:
L6171: Press the OK button, then press and hold the
help button for 3 seconds.
L6191: Press and hold the help button for 3 seconds.
L6171/L6191

5Install software
Note: If your computer does not have a CD/DVD drive or you are
using a Mac, an Internet connection is required to obtain the product
software.
To print from a Chromebook™, go to
www.epson.com.jm/support/gcp for instructions.
1 Make sure the product is NOT CONNECTED to your
computer.
Windows®:If you see a Found New Hardware screen, click
Cancel and disconnect the USB cable.
2 Insert the product CD or download and run your product’s
software package. For the latest software, visit:
L6171
www.epson.com.jm/support/L6171
L6191
www.epson.com.jm/support/L6191
3 Follow the instructions on the computer screen to run the
setup program.
4 When you see the Select Your Connection screen, select
one of the following:
• Wireless connection
In most cases, the software installer automatically
attempts to set up your wireless connection. If setup
is unsuccessful, you may need to enter your network
name (SSID) and password.
• Direct USB connection
Make sure you have the USB cable ready.
• Wired network connection
Make sure you have an Ethernet cable (not included).
Mobile printing
Connect wirelessly from your smartphone, tablet, or computer.
Print documents and photos from across the room or around
the world:
• Print directly from a smartphone or tablet using iOS or
Android™ with Epson iPrint™. Simply connect your printer
and device to the same network and tap the action icon to
select the print option.
• Use Epson Print Enabler (free from Google Play™) with
Android devices (v4.4 or later). Then connect your printer
and device to the same network and tap the menu icon to
select the print option.
• Print remotely with Epson Connect™ and Google Cloud
Print™. See your online User’s Guide for instructions or
learn more at www.epson.com.jm/connect.
EPSON is a registered trademark, Epson Connect and Epson iPrint are trademarks, and
EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation.
Designed for Excellence is a trademark of Epson America, Inc.
Mac is a trademark of Apple Inc., registered in the U.S. and other countries.
Android, Google Cloud Print, Chromebook, and Google Play are trademarks of Google Inc.
General Notice: Other product names used herein are for identication purposes only and may
be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2017 Epson America, Inc., 8/17
Printed in XXXXXX CPD-54012
3 Insert paper with the glossy or printable side down.
Note: Make sure the paper is loaded against the front edge
guide and not sticking out from the end of the cassette.
4 Slide the side edge guides against the paper, but not too
tightly. Close the front of the cassette.
5 Keep the cassette flat as you insert it all the way.
6 Pull out the output tray.
7 Select the paper settings on the product’s control panel.
4Connect the fax line (L6191)
1 Connect the phone cord to a telephone wall jack and
to the LINE port on your product. See the online User’s
Guide for more information.
2 Press Proceed to set up the fax, or press Set Up Later to
set it up later.
Any problems?
Network setup was unsuccessful.
• Make sure you select the right network name (SSID).
• Restart your router (turn it off and then on), then try to
connect to it again.
• The printer can only connect to a network that supports
2.4 GHz connections. If your router offers both 2.4 GHz
and 5 GHz connections, make sure 2.4 GHz is enabled.
• If you see a firewall alert message, click Unblock or Allow
to let setup continue.
• If your network has security enabled, make sure you enter
your network password (WEP key or WPA passphrase)
correctly. Be sure to enter your password in the correct
case.
There are lines or incorrect colors in my printouts.
Run a nozzle check to see if any of the print head nozzles are
clogged. Then clean the print head, if necessary. See the online
User’s Guide for more information.
The product’s screen is dark.
Make sure your product is turned on, and press any button
(L6171) or touch the screen (L6191) to wake it from sleep
mode.
Setup is unable to find my product after connecting it
with a USB cable.
Make sure your product is on and securely connected.
Any questions?
User’s Guide
Windows: Click the icon on your desktop or Apps screen to
access the online User’s Guide.
Mac: Click the icon in Applications/Epson Software/Guide
to access the online User’s Guide.
If you don’t have a User’s Guide icon, go to the Epson website,
as described to the right.
Technical support
Visit www.epson.com.jm/support and search for your product
to download drivers, view manuals, get FAQs, or contact
Epson.
You can also speak to a service technician by calling one of
these numbers:
Argentina (54 11) 5167-0300 Honduras** 800-0122
0800-288-37766 Code: 8320
Bolivia* 800-100-116 Mexico 01-800-087-1080
Chile (56 2) 2484-3400 Mexico City (52 55) 1323-2052
Colombia 018000-915235 Nicaragua* 00-1-800-226-0368
Bogota (57 1) 523-5000 Panama* 00-800-052-1376
Costa Rica 800-377-6627 Paraguay 009-800-521-0019
Dominican Peru 0800-10126
Republic* 1-888-760-0068 Lima (51 1) 418-0210
Ecuador* 1-800-000-044 Uruguay 00040-5210067
El Salvador* 800-6570 Venezuela (58 212) 240-1111
Guatemala* 1-800-835-0358
* Contact your local phone company to call this toll free number from a mobile
phone.
** Dial the first 7 digits, wait for a message, then enter the code.
If your country does not appear on the list, contact your nearest
Epson sales office. Toll or long distance charges may apply.
Need paper and ink?
Ensure peak performance and brilliant results
with Genuine Epson®Ink and specialty
papers, engineered specifically for Epson
printers. You can purchase them from an
Epson authorized reseller. To find the
nearest one, visit www.epson.com.jm or
contact Epson as described in “Any
questions?” on this sheet.
L6171/L6191 replacement inks
Color Part number
Black 504
Cyan 504
Magenta 504
Yellow 504

5Install software
Note: If your computer does not have a CD/DVD drive or you are
using a Mac, an Internet connection is required to obtain the product
software.
To print from a Chromebook™, go to
www.epson.com.jm/support/gcp for instructions.
1 Make sure the product is NOT CONNECTED to your
computer.
Windows®:If you see a Found New Hardware screen, click
Cancel and disconnect the USB cable.
2 Insert the product CD or download and run your product’s
software package. For the latest software, visit:
L6171
www.epson.com.jm/support/L6171
L6191
www.epson.com.jm/support/L6191
3 Follow the instructions on the computer screen to run the
setup program.
4 When you see the Select Your Connection screen, select
one of the following:
• Wireless connection
In most cases, the software installer automatically
attempts to set up your wireless connection. If setup
is unsuccessful, you may need to enter your network
name (SSID) and password.
• Direct USB connection
Make sure you have the USB cable ready.
• Wired network connection
Make sure you have an Ethernet cable (not included).
Mobile printing
Connect wirelessly from your smartphone, tablet, or computer.
Print documents and photos from across the room or around
the world:
• Print directly from a smartphone or tablet using iOS or
Android™ with Epson iPrint™. Simply connect your printer
and device to the same network and tap the action icon to
select the print option.
• Use Epson Print Enabler (free from Google Play™) with
Android devices (v4.4 or later). Then connect your printer
and device to the same network and tap the menu icon to
select the print option.
• Print remotely with Epson Connect™ and Google Cloud
Print™. See your online User’s Guide for instructions or
learn more at www.epson.com.jm/connect.
EPSON is a registered trademark, Epson Connect and Epson iPrint are trademarks, and
EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation.
Designed for Excellence is a trademark of Epson America, Inc.
Mac is a trademark of Apple Inc., registered in the U.S. and other countries.
Android, Google Cloud Print, Chromebook, and Google Play are trademarks of Google Inc.
General Notice: Other product names used herein are for identication purposes only and may
be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2017 Epson America, Inc., 8/17
Printed in XXXXXX CPD-54012
3 Insert paper with the glossy or printable side down.
Note: Make sure the paper is loaded against the front edge
guide and not sticking out from the end of the cassette.
4 Slide the side edge guides against the paper, but not too
tightly. Close the front of the cassette.
5 Keep the cassette flat as you insert it all the way.
6 Pull out the output tray.
7 Select the paper settings on the product’s control panel.
4Connect the fax line (L6191)
1 Connect the phone cord to a telephone wall jack and
to the LINE port on your product. See the online User’s
Guide for more information.
2 Press Proceed to set up the fax, or press Set Up Later to
set it up later.
Any problems?
Network setup was unsuccessful.
• Make sure you select the right network name (SSID).
• Restart your router (turn it off and then on), then try to
connect to it again.
• The printer can only connect to a network that supports
2.4 GHz connections. If your router offers both 2.4 GHz
and 5 GHz connections, make sure 2.4 GHz is enabled.
• If you see a firewall alert message, click Unblock or Allow
to let setup continue.
• If your network has security enabled, make sure you enter
your network password (WEP key or WPA passphrase)
correctly. Be sure to enter your password in the correct
case.
There are lines or incorrect colors in my printouts.
Run a nozzle check to see if any of the print head nozzles are
clogged. Then clean the print head, if necessary. See the online
User’s Guide for more information.
The product’s screen is dark.
Make sure your product is turned on, and press any button
(L6171) or touch the screen (L6191) to wake it from sleep
mode.
Setup is unable to find my product after connecting it
with a USB cable.
Make sure your product is on and securely connected.
Any questions?
User’s Guide
Windows: Click the icon on your desktop or Apps screen to
access the online User’s Guide.
Mac: Click the icon in Applications/Epson Software/Guide
to access the online User’s Guide.
If you don’t have a User’s Guide icon, go to the Epson website,
as described to the right.
Technical support
Visit www.epson.com.jm/support and search for your product
to download drivers, view manuals, get FAQs, or contact
Epson.
You can also speak to a service technician by calling one of
these numbers:
Argentina (54 11) 5167-0300 Honduras** 800-0122
0800-288-37766 Code: 8320
Bolivia* 800-100-116 Mexico 01-800-087-1080
Chile (56 2) 2484-3400 Mexico City (52 55) 1323-2052
Colombia 018000-915235 Nicaragua* 00-1-800-226-0368
Bogota (57 1) 523-5000 Panama* 00-800-052-1376
Costa Rica 800-377-6627 Paraguay 009-800-521-0019
Dominican Peru 0800-10126
Republic* 1-888-760-0068 Lima (51 1) 418-0210
Ecuador* 1-800-000-044 Uruguay 00040-5210067
El Salvador* 800-6570 Venezuela (58 212) 240-1111
Guatemala* 1-800-835-0358
* Contact your local phone company to call this toll free number from a mobile
phone.
** Dial the first 7 digits, wait for a message, then enter the code.
If your country does not appear on the list, contact your nearest
Epson sales office. Toll or long distance charges may apply.
Need paper and ink?
Ensure peak performance and brilliant results
with Genuine Epson®Ink and specialty
papers, engineered specifically for Epson
printers. You can purchase them from an
Epson authorized reseller. To find the
nearest one, visit www.epson.com.jm or
contact Epson as described in “Any
questions?” on this sheet.
L6171/L6191 replacement inks
Color Part number
Black 504
Cyan 504
Magenta 504
Yellow 504