Epson Stylus Photo RX600 User manual

CPD-17417
4048049-00

Welcome!
Did you know you can copy and print using your Epson Stylus®
Photo RX600 without using your computer?
Try the step-by-step instructions for these projects:
❍Copying 4 ×6-inch photos (page 1)
❍Printing photos from a memory card (page 5)
❍Printing a photo from 35 mm film (page 9)
There’s much more you can do with your Stylus Photo RX600! See
some examples on page 16.
For detailed instructions on using the RX600,
see your User’s Guide.
For instructions on setting up your RX600 and
connecting it to a computer, see the Start Here
sheet.
Epson and Epson Stylus are registered trademarks and PRINT Image Matching, and the PRINT Image
Matching logo are trademarks of Seiko Epson Corporation.
BorderFree is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
© 2004 Epson America, Inc. 1/04

1
Copying a Photo
Here’s how to make a copy of a 4 ×6-inch photo using Epson
Premium Glossy Photo Paper:
1Press the On button to turn on the Stylus Photo RX600.
2Open the output tray.
3Flip the feeder guard forward.
4Insert a sheet of 4 ×6-inch Premium Glossy Photo Paper short
edge first against the right edge of the sheet feeder, under the tab,
with the shiny side up.
Output tray

2
5Press the sides of the left edge guide together and slide it against
the paper (but not too tightly). Make sure the paper is under the
tab on the left edge guide.
6Flip the feeder guard back over the paper.
7Open the scanner lid.

3
8Place your 4 ×6-inch photo face-down on the glass, in the upper
left corner. Move your photo about 0.1 inch from the top and
side edge so your entire photo is scanned.
9Close the scanner lid.
10 Press the Copy button to set the RX600 to Copy mode.
11 Press the Menu button to select Copy mode layout options.
0.1 in
0.1 in
Move the photo
in about 0.1 inch
from the edges
Copy
button
Menu
button

4
12 Use the uand dbuttons to
choose Copy Layout, then use
the l and rbuttons to change
the setting to BorderFree.
13 Press the OK button.
14 Choose the following settings:
❍Copies: the number of prints
❍Reduce/Enlarge: AutoFitPage
❍Zoom In/Out: leave this setting blank (if it is accidently
changed, reset the Reduce/Enlarge setting to AutoFitPage)
❍Paper Type: Prem.Glossy
❍Paper Size: 4x6in.
❍Quality: BestPhoto
Use the uand dbuttons to choose copy options, then use
the land rbuttons to change settings.
15 Press the xColor button to make a color copy or press the
xB&W button to make a black and white copy.
Note: To cancel copying, press the yStop button. Canceling appears on
the LCD screen.

5
Printing Photos from a Memory Card
Here’s how to print 4 ×6-inch photos on Premium Glossy Photo
Paper directly from your memory card.
1Press the On button to turn on the Stylus Photo RX600.
2Open the output tray.
3Flip the feeder guard forward.
4Insert a sheet of 4 ×6-inch Epson Premium Glossy Photo Paper
short edge first against the right edge of the sheet feeder, under
the tab, with the shiny side up.
Output tray

6
5Press the sides of the left edge guide together and slide it against
the paper (but not too tightly). Make sure the paper is under the
tab on the left edge guide.
6Flip the feeder guard back over the paper.
7Press the Memory Card button to set the RX600 to Memory
Card mode.
Memory
Card button

7
8Open the memory card slot cover.
9Insert your memory card into the correct slot. Be careful not to
force it in (it won’t go in all the way).
Note:
Do not insert more than one card.
The memory card light flashes, then turns green. Close the cover.
CompactFlash™or
Microdrive™(bottom)
Memory Stick®
(middle)
SD or MMC
(middle)
SmartMedia™
(top)
xD
(top)
Memory card light

8
If the light doesn’t turn green, or if you see the message No
memory card. Operation Canceled on the LCD screen, the
card may be inserted incorrectly or may not be supported.
Note:
To remove the card, first make sure your RX600 is not printing and
the memory card light is not flashing. Then open the memory card
slot cover and pull the card straight out of the slot.
10 Use the uand dbuttons to choose Basic Print 4 x 6", then use
the land rbuttons to choose Select Print. Press the OK button.
(For advanced printing options, see your User’s Guide.)
11 Use the land rbuttons to scroll through and select a photo,
then use the uand dbuttons to choose the number of copies to
print of that photo.
12 Press the xColor button to print a color photo. (You can’t print
in black and white from this mode.)
Note:
To cancel printing, press the yStop button. Canceling appears on the
LCD screen.