Epson DX5 X 1 Use and care manual

1
Epson
Epson
Epson
Epson DX5
DX5
DX5
DX5 X
X
X
X 1
1
1
1 Printhead
Printhead
Printhead
Printhead
Calibration
Calibration
Calibration
Calibration and
and
and
and Maintenance
Maintenance
Maintenance
Maintenance
31
31
31
31
st
st
st
st
Jan
Jan
Jan
Jan .,
.,
.,
., 201
201
201
201 3
3
3
3
Version V 3 .0
All manuals and user guides at all-guides.com

2
Contents
Contents
Contents
Contents
Chapter 1: Computer Requirement ................................................................3
Chapter 2:Installation......................................................................................4
Chapter 3:Chara c teristic...................................................................................5
Chapter 4:Board System................................................................................. 6
Chapter 5:Software Installation ......................................................................7
Chapter 6:Software Interface..........................................................................9
Chapter 7: Software Calibration......................................................................10
Chapter 8: Other Functions and Parameters ................................................. 14
Chapter 9: Maintenance..................................................................................15
Chapter 10: Troubleshoot................................................................................2 1
Chapter 11: Output Chart.................................................................................2 2
All manuals and user guides at all-guides.com

3
Chapter
Chapter
Chapter
Chapter 1:
1:
1:
1: Computer
Computer
Computer
Computer Requirement
Requirement
Requirement
Requirement
1)
1)
1)
1) Basic
Basic
Basic
Basic requirement:
requirement:
requirement:
requirement:
-CPU: 2.0 GHz or higher
-Memory: 1Gb or higher
-Hard disk: 80 Gb (recommend 20Gb free space)
-Mother board: USB connection equipped
-Network card
-Operating system: Microsoft Windows (2000, XP)
2)
2)
2)
2) Recommendatory
Recommendatory
Recommendatory
Recommendatory requirement:
requirement:
requirement:
requirement:
-CPU: 3.0 GHz or higher
-Memory: 2 Gb or higher
-Hard disk: 200 Gb or higher (NTFS format)
-Motherboard: USB connection equipped
-Network card
-Operating system: Microsoft Windows (2000, XP)
NOTICE:
NOTICE:
NOTICE:
NOTICE: Suggest user format your hard disk into 2 partitions (NTFS). The first partition is used for installing
OS and other software, the second partition is used to save pictures and work files.
All manuals and user guides at all-guides.com

4
Chapter
Chapter
Chapter
Chapter 2:
2:
2:
2: Installation
Installation
Installation
Installation
1) Move the packing box to the working site and avoid strong shaking.
2) Disassemble the wooden packing box from top to bottom. Check whether the parts are complete or not
according to the packing list.
3) Lift the printer out by a forklift, and move it to the installation site.
4) Check if the printer is level.
5) Get rid of all the parts that stabilize the carriage holder, and install all the spare parts.
6) Move the carriage to the right of printer, then move back to the left manually. During this process, checks if
there are abnormal resistance and carefully inspect the belt & the encoder sensor are situated in proper
position
7) Ground the printer. The grounded voltage shouldn ’ t be more than 0.3V, and the grounded resistance should
be less than 3 Ω .
8) Connect the USB cable between printer and computer. Check if the wires and data cables areplugged in
properly.
9) Install the output and the rip software.
10) Move the carriage to middle of printing platform, turn on the printer, let the carriage move to home position,
and keep your hand on the emergency button for turning off the printer if problem happens suddenly.
11) Send a file to print to test the condition of the printer.
12) Install ptinthead and dampers, connect the ink tube from damper to special solvent, and use auto clean
function to clean the printhead
13) Load ink bottle, and use auto clean function to suck the ink from ink bottle to printhead.
14) Print nozzle checking and observe the condition of printheads. It is recommended to keep a copy of the test
for reference in the future.
15) Printhead alignment.
16) Start to Print.
All manuals and user guides at all-guides.com

5
Chapter
Chapter
Chapter
Chapter 3:
3:
3:
3: Characteristics
Characteristics
Characteristics
Characteristics
�Printhead: 1 pc (Epson DX5)
�Resolution: 1440\1080\720DPI
�Color: 4 colors
�Printmode: 4,6,8,12 Pass
�Output mode ：File or TCP/IP(Rip and Print at the same time)
�Output preview ：Convert prn/prt file into a small bmp file for previewing
�Printhead usage: Able to turn on/off each printhead channel
�Print intelligently ：Skip white area
�Muti-printing: Able to print single or different image continuously
�Automatically flash jetting ：Automatically clean printheads by flash jetting during printing
�Home flash jet: Prevent nozzles from clogging while not in printing state
�Color bar ：Prevent nozzles from clogging, and observe nozzles status. Able to set the
width of color bar and the instance from image
�Able to align printheads, step difference ,and bi-direction difference during printing
�Printing direction: uni-direction to left, uni-direction to right, bi-direction
�Edge feather: Lighten pass line
�Cleaning System: auto-cleaning, no need to use tools (Syringe) to clean
�Control Panel: use with control panel, it is more convenience
All manuals and user guides at all-guides.com

6
Chapter
Chapter
Chapter
Chapter 4:
4:
4:
4: Board
Board
Board
Board S
S
S
S ystem
ystem
ystem
ystem
Printhead
Printhead
Printhead
Printhead B
B
B
B oard
oard
oard
oard
Mainboard
Mainboard
Mainboard
Mainboard
Encoder sensor
Magnetic sensor
Processing
Indication
Optical Fiber plug
Printhead cable
plug 1
Power flat
cable plug
X Driver DB plug
Power cable Plug
Y Driver DB plug
Pump plug
Power supply
plug
USB data port
Processing Indication
Optical Fiber plug
Status LED
Power LED
Status LED
Power LED
Printhead cable
plug 2
Control panel plug
All manuals and user guides at all-guides.com

7
Note: 1. After turn ing on the machine till the carriage moving back to home position, the processing indication
shows as: A. – 1 – 4 – 0.
Main board and Head board show the same indication .
2. The two power cable plug both are 20Pin.
3. In normal state, RUN LED is blinking; LINK LED is on; BUSY LED is on （On Main board, when
carriage moves, BUSY LED is on, otherwise it is off ）;ERROR LED is off(only on when there is problem).
Chapter
Chapter
Chapter
Chapter 5.
5.
5.
5.
Software
Software
Software
Software Installation
Installation
Installation
Installation
This software consist of printer driver, printing adjustment and picture printing functions.
Please follow the following steps to install the software:
1) Turn on the computer till the system is ready, copy UDT_PrintExp
UDT_PrintExp
UDT_PrintExp
UDT_PrintExp to your computer, un-zip to get
UDT_PrintExp
UDT_PrintExp
UDT_PrintExp
UDT_PrintExp folder. Start to install:
2) Double click to install
All manuals and user guides at all-guides.com

8
3) Connet the USB data cable to the computer, and turn on the machine.
Look for PrintDrv_new
PrintDrv_new
PrintDrv_new
PrintDrv_new file
file
file
file in the folder of UDT_PrintExp.
UDT_PrintExp.
UDT_PrintExp.
UDT_PrintExp.
It shows as above after finished installing the control software.
All manuals and user guides at all-guides.com

9
Chapter
Chapter
Chapter
Chapter
6.
6.
6.
6. Software
Software
Software
Software Interface
Interface
Interface
Interface
1)
1)
1)
1) I
I
I
I ntroduction:
ntroduction:
ntroduction:
ntroduction:
D
ouble click to open the software.
2)
2)
2)
2) Tool
Tool
Tool
Tool s
s
s
s bar
bar
bar
bar
W e can speed up the implementation of commands by using tools bar which are commonly used function in the
software .
3)Status
3)Status
3)Status
3)Status Bar
Bar
Bar
Bar
From the left to the right: Printer
Printer
Printer
Printer status,
status,
status,
status, Flash
Flash
Flash
Flash jetting
jetting
jetting
jetting function
function
function
function status,
status,
status,
status, Carriage
Carriage
Carriage
Carriage position
position
position
position .
Preview
Preview
Preview
Preview
Image
information
Condition bar
Tools bar
Directory of
printing jobs
Jobs to
print
Printing job list
Configuration
Configuration
Configuration
Configuration definition
definition
definition
definition ：
UDT_DX5_1H4C_LA
UDT_DX5_1H4C_LA
UDT_DX5_1H4C_LA
UDT_DX5_1H4C_LA ：LA model with
1 printhead.
UDT_DX5_1H4C_LB
UDT_DX5_1H4C_LB
UDT_DX5_1H4C_LB
UDT_DX5_1H4C_LB ：LB machine with
1 printhead.
UDT_DX5_
UDT_DX5_
UDT_DX5_
UDT_DX5_ 1
1
1
1 H4C_
H4C_
H4C_
H4C_ W,WA
W,WA
W,WA
W,WA ： W, W A model
with 1 printhead.
All manuals and user guides at all-guides.com

10
Chapter
Chapter
Chapter
Chapter 7.
7.
7.
7.
Software
Software
Software
Software Calibration
Calibration
Calibration
Calibration
1. Nozzle checking: P rint the nozzle checking to check the condition of the printhead.
Make
Make
Make
Make sure
sure
sure
sure to
to
to
to turn
turn
turn
turn off
off
off
off the
the
the
the Eclosion
Eclosion
Eclosion
Eclosion (Feather)
(Feather)
(Feather)
(Feather) function
function
function
function before
before
before
before doing
doing
doing
doing the
the
the
the alignment.
alignment.
alignment.
alignment.
2. Vertical calibration: Observe the physical alignment of printheads.
（This
This
This
This step
step
step
step is
is
is
is not
not
not
not aligned
aligned
aligned
aligned well
well
well
well which
which
which
which will
will
will
will affect
affect
affect
affect the
the
the
the following
following
following
following adjustment
adjustment
adjustment
adjustment ）
Align the physical vertical position of printhead.
The first pass line is the reference; observe whether the second pass line is perfectly aligned with the first
pass line. If not, then we need to adjust the carriage plate. There are 3 situations:
1) The two pass is perfectly aligned, no need to adjust:
2) The second is on the left side of the first pass:
Adjust method:
A. Loosen the 3 screws on the carriage plate:
B. Turn the screw clockwise:
First pass
Second pass
First pass
Second pass
All manuals and user guides at all-guides.com

11
3) The second is on the right side of the first pass:
Adjust method:
Note:
Note:
Note:
Note: Every
Every
Every
Every time
time
time
time after
after
after
after the
the
the
the adjustment,
adjustment,
adjustment,
adjustment, before
before
before
before print
print
print
print another
another
another
another vertical
vertical
vertical
vertical calibration,
calibration,
calibration,
calibration, it
it
it
it is
is
is
is required
required
required
required to
to
to
to tighten
tighten
tighten
tighten 3
3
3
3
screws
screws
screws
screws on
on
on
on the
the
the
the carriage
carriage
carriage
carriage plate.
plate.
plate.
plate. Keep
Keep
Keep
Keep adjusting
adjusting
adjusting
adjusting until
until
until
until the
the
the
the second
second
second
second pass
pass
pass
pass is
is
is
is perfectly
perfectly
perfectly
perfectly aligned
aligned
aligned
aligned with
with
with
with the
the
the
the first
first
first
first
pass.
pass.
pass.
pass.
3. Color offset: C olor offset is to align all color in order to print good quality images.
Tip: Based on the "0" position, the color lines should totally matched with the Black line, if not, find the best one
show ing on the printed out color offset, then input the corresponding values in the software. Note that values are
accumulated.
If the "0" position is not the perfect matching one, then we have to adjust the figure on the software. Go to Option
Option
Option
Option
–Calibration
Calibration
Calibration
Calibration –Color
Color
Color
Color Offset
Offset
Offset
Offset
:
A. Loosen the 3 screws on the carriage plate:
B. Turn the screw anti-clockwise:
First pass
Second pass
Values are input here.
All manuals and user guides at all-guides.com

12
After input the value , print the alignment again. And observe if the "0" position is the best or not. If not, repeat the
above procedure until the best result come out.
4. Bi-Dir offset
Bi-Dir offset is to make sure there is no bi-difference while using different speed to print. Bi-Dir offset will be set
for different printing speed.
If the "0" position is not the perfect matching one, then we have to adjust the value on the software. Go to Option
Option
Option
Option
–Calibration
Calibration
Calibration
Calibration -Bi-Dir
Bi-Dir
Bi-Dir
Bi-Dir Offset
Offset
Offset
Offset
Repeat the test until the “ 0 ” is facing each other perfectly.
5. Step offset
The Step offset locates on Option
Option
Option
Option –Calibration
Calibration
Calibration
Calibration –Step
Step
Step
Step Offset
Offset
Offset
Offset
:
To adjust the step offset, firstly adjust the Base
Base
Base
Base Step,
Step,
Step,
Step, then the value of other pass will be calculated
automatically. And slightly adjustment is needed according to actual printing.
Input the value here. This
value is accumulated. Press
“Print ”to print the test
pattern.
04
OK NG
-4
-8816 -16
Input the offset
value
here.
All manuals and user guides at all-guides.com

13
Based on the "0" position, input the value which two line are perfectly overlapped. After input the value , test
again to check the result. The step value will be different according to different media.
Note:
Note:
Note:
Note: Turn
Turn
Turn
Turn off
off
off
off the
the
the
the Eclosion
Eclosion
Eclosion
Eclosion (Feather)
(Feather)
(Feather)
(Feather) function
function
function
function first
first
first
first while
while
while
while adjusting
adjusting
adjusting
adjusting the
the
the
the step
step
step
step offset.
offset.
offset.
offset. Adjust
Adjust
Adjust
Adjust to
to
to
to get
get
get
get the
the
the
the best
best
best
best
step
step
step
step value.
value.
value.
value. Then
Then
Then
Then test
test
test
test print
print
print
print to
to
to
to see
see
see
see whether
whether
whether
whether there
there
there
there is
is
is
is banding
banding
banding
banding on
on
on
on the
the
the
the image.
image.
image.
image. If
If
If
If so,
so,
so,
so, use
use
use
use the
the
the
the Eclosion
Eclosion
Eclosion
Eclosion (Feather)
(Feather)
(Feather)
(Feather)
function
function
function
function to
to
to
to reach
reach
reach
reach your
your
your
your best
best
best
best image
image
image
image quality.
quality.
quality.
quality.
The
The
The
The adjustment
adjustment
adjustment
adjustment of
of
of
of software
software
software
software has
has
has
has been
been
been
been completed
completed
completed
completed now
now
now
now
Have to input +2.
All manuals and user guides at all-guides.com

14
Chapter
Chapter
Chapter
Chapter
8.
8.
8.
8. Other
Other
Other
Other Functions
Functions
Functions
Functions and
and
and
and Parameters
Parameters
Parameters
Parameters
1
1
1
1 Printhead
Printhead
Printhead
Printhead voltage
voltage
voltage
voltage
Normally the voltage function is not being used. The range of adjusting voltage is -42V to +1.3V.
2.
2.
2.
2. Other
Other
Other
Other function
function
function
function
Click Option on the main interface of the software, it shows the following window:
Details of the print option:
1.
1.
1.
1. Flash
Flash
Flash
Flash Jetting
Jetting
Jetting
Jetting frequency:
frequency:
frequency:
frequency:
S et the flash jetting frequency when the printer is on standby status.
All manuals and user guides at all-guides.com

15
2.
2.
2.
2. Clean
Clean
Clean
Clean Option:
Option:
Option:
Option:
1) Click to set the carriage go back to the flash jetting position for jetting during printing;
2) Print pass is to set every XX pass, carriage go back to the flash jetting position for jetting;
3) Clean Mode is Flash Jetting;
4) There are three options in Clean Time, Fast means non - stop jetting, Normal means jetting for 0.5s ,
, Long means jetting for 1s.
3.
3.
3.
3. Eclosion(Feather
Eclosion(Feather
Eclosion(Feather
Eclosion(Feather function):
function):
function):
function):
To blur the pass line, feather pass edge.
1) Option: Enable/Disable the feather function; 2) Type of Eclosion; 3) Value of Eclosion.
4.
4.
4.
4. Color
Color
Color
Color Bar:
Bar:
Bar:
Bar:
1) Distance (mm): Setup for distance between the color bar and the picture;
2) Width (mm): Setup for the width of the whole color bars ;
3) Setup for the position of color bar (in the right/left/both side of the image ).
5.
5.
5.
5. Smart
Smart
Smart
Smart Print:
Print:
Print:
Print:
Set up for automatically skip white.
6.
6.
6.
6. Auto
Auto
Auto
Auto feed
feed
feed
feed after
after
after
after printed:
printed:
printed:
printed:
Set up for automatically feed media after print ing (mm).
All manuals and user guides at all-guides.com

16
Chapter
Chapter
Chapter
Chapter
9.
9.
9.
9. Maintenance
Maintenance
Maintenance
Maintenance
9.1
9.1
9.1
9.1 Normal
Normal
Normal
Normal Cleaning
Cleaning
Cleaning
Cleaning
Click Clean on the main interface of the software. There are two modes of cleaning, Standard
Standard
Standard
Standard and Depth.
Depth.
Depth.
Depth.
Normally Standard mode is used.
9.2
9.2
9.2
9.2 Cleaning
Cleaning
Cleaning
Cleaning procedures
procedures
procedures
procedures for
for
for
for nozzle
nozzle
nozzle
nozzle clogging:
clogging:
clogging:
clogging:
1. Disconnect the tube connector for the tube from cartridge to the damper. Choose Standard clean mode the
suck out the ink in the damper. (2 times)
2. Use an extend tube to connect the damper, put the other side of the extend tube into the appointed Flush.
Choose Depth clean mode to clean the damper and the printhead at the same time.(3 times)
3. Take out the extend tube from the Flush, and keep it out in the air. Choose Depth clean mode to suck out the
Flush inside the damper and the printhead. After that connect the damper to the ink incoming tube and fill ink
again.
4. Test print.
9.3
9.3
9.3
9.3 Carriage
Carriage
Carriage
Carriage Bearing
Bearing
Bearing
Bearing and
and
and
and Steel
Steel
Steel
Steel Rail
Rail
Rail
Rail Maintenance
Maintenance
Maintenance
Maintenance
Due to the carriage slides on four steel plates and eight bearing, clean and lubricate four steel plates with grease
everyday.
Ⅰ. Wipe a thin layer of grease on steel plates to maintain cleanliness and grease everyday before and after
usage.
Ⅱ. Be aware of the smoothness of the carriage bearing.
All manuals and user guides at all-guides.com

17
9.4
9.4
9.4
9.4 Daily
Daily
Daily
Daily Maintenance
Maintenance
Maintenance
Maintenance
1. Print the nozzle checking before turn off the machine to make sure the printhead is in normal condition
2. Turn off the software, carriage go back to Home position automatically . Turn off the machine, the carriage stay
at the Home position.
3. Use sponge stick with appointed Flush to clean the cap and the wiper everyday before turning on the machine .
9.5
9.5
9.5
9.5 Short
Short
Short
Short term
term
term
term shut
shut
shut
shut down
down
down
down (3~7
(3~7
(3~7
(3~7 days)
days)
days)
days)
1. Disconnect the tube connector on top of the damper . Use Standard clean mode to empty the ink in the damper.
(2 times)
2. Use a extend tube to connect the dampe r to the appointed Flush.
Choose Depth clean mode to clean the damper and the printhead at the same time.(2 times)
3. Take out the extend tube from the Flush, and keep it out in the air. Choose Depth clean mode to empty the
Flush inside the damper and the printhead. Use the tube cove r to seal the ink incoming tube, keep the cartridge
back to Home position and make sure the capping pad is perfectly capping the printhead.
9.6
9.6
9.6
9.6 Long
Long
Long
Long term
term
term
term shut
shut
shut
shut down
down
down
down (More
(More
(More
(More than
than
than
than a
a
a
a week)
week)
week)
week)
1. Print status before turn off the machine, make sure printhead in good condition..
2. Disconnect the tube connector on top of dampers, let the ink flow back to the cartridge.
3. Use the extend tube to connect them to the appointed Flush. Choose Depth clean mode to clean the damper
and the printhead at the same time. C lean one color at a time , use a cap to cover other three color channel.
All manuals and user guides at all-guides.com

18
4 . Take out the extend tube from the Flush, and keep it out in the air. Choose Depth clean mode to empty the
Flush inside the damper and the printhead.
5. Take out the four tubes(K,C,M,Y) from the cartridge. Use the extend tube to connect them to flush.
All manuals and user guides at all-guides.com

19
Use a extend ink tube to connect the ink tube to ink pump
Choose “ Ink Fill ” mode at control panel, use ink pump to f lush ink tube until it is clear. Then take out the tube from
the Flush, choose “ Ink Fill ” mode, empty the Flush inside the ink tube. Clean K,C,M,Y tube one by one
After cleaning, use cap and fresh warp to seal the ink tubes.
All manuals and user guides at all-guides.com

20
6. Take out four cartridges, use fresh wrap to seal the ink supply hole and keep the cartridges in the proper
place.
7. K eep the carriage back to Home position and make sure the cap is perfectly sealing the printhead.
All manuals and user guides at all-guides.com