Epson SC-B7000 Series User manual

SC-F7000 Series
SC-B7000 Series
Large Format Color Inkjet Printer
SERVICE MANUAL
SEIJ12010
Confidential

Confidential
Notice:
All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.
The contents of this manual are subject to change without notice.
All efforts have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly
appreciate being informed of them.
The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
General Notice: Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their
respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2012 SEIKO EPSON CORPORATION.
COMMERCIAL PRINTER CS QUALITY ASSURANCE DEPARTMENT

Confidential
PRECAUTIONS
Precautionary notations throughout the text are categorized relative to 1) Personal injury and 2) Damage to equipment.
DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing
procedures preceded by DANGER Headings.
WARNING Signals a precaution which, if ignored, could result in damage to equipment.
The precautionary measures itemized below should always be observed when performing repair/maintenance procedures.
DANGER
1. ALWAYS DISCONNECT THE PRODUCT FROM THE POWER SOURCE AND PERIPHERAL DEVICES PERFORMING ANY MAINTENANCE OR
REPAIR PROCEDURES.
2. NO WORK SHOULD BE PERFORMED ON THE UNIT BY PERSONS UNFAMILIAR WITH BASIC SAFETY MEASURES AS DICTATED FOR ALL
ELECTRONICS TECHNICIANS IN THEIR LINE OF WORK.
3. WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL
INSTRUCTED TO DO SO. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER
SUPPLY AND OTHER ELECTRONIC COMPONENTS.
4. WHEN DISASSEMBLING OR ASSEMBLING A PRODUCT, MAKE SURE TO WEAR GLOVES TO AVOID INJURY FROM METAL PARTS WITH
SHARP EDGES.
WARNING
1. REPAIRS ON EPSON PRODUCT SHOULD BE PERFORMED ONLY BY AN EPSON CERTIFIED REPAIR TECHNICIAN.
2. MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING
PLATE. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO
THE POWER SOURCE.
3. ALWAYS VERIFY THAT THE EPSON PRODUCT HAS BEEN DISCONNECTED FROM THE POWER SOURCE BEFORE REMOVING OR
REPLACING PRINTED CIRCUIT BOARDS AND/OR INDIVIDUAL CHIPS.
4. IN ORDER TO PROTECT SENSITIVE MICROPROCESSORS AND CIRCUITRY, USE STATIC DISCHARGE EQUIPMENT, SUCH AS ANTI-STATIC
WRIST STRAPS, WHEN ACCESSING INTERNAL COMPONENTS.
5. REPLACE MALFUNCTIONING COMPONENTS ONLY WITH THOSE COMPONENTS BY THE MANUFACTURE; INTRODUCTION OF SECOND-
SOURCE ICs OR OTHER NON-APPROVED COMPONENTS MAY DAMAGE THE PRODUCT AND VOID ANY APPLICABLE EPSON WARRANTY.
6. WHEN AIR DUSTER IS USED ON THE REPAIR AND THE MAINTENANCE WORK, THE USE OF THE AIR DUSTER PRODUCTS CONTAINING
THE INFLAMMABLE GAS IS PROHIBITED.
7. MAKE SURE AN ANTIVIRUS SOFTWARE IS INSTALLED ON THE COMPUTER USED FOR SERVICE SUPPORT. BE SURE TO HAVE THE
LATEST VIRUS DEFINITION FILE FOR THE SOFTWARE.

Confidential
About This Manual
This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included
herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.
Manual Configuration
This manual consists of six chapters and Appendix.
CHAPTER 1.PRODUCT DESCRIPTIONS
Provides a general overview and specifications of the product.
CHAPTER 2.TROUBLESHOOTING
Describes the step-by-step procedures for the troubleshooting.
CHAPTER 3.DISASSEMBLY / ASSEMBLY
Describes the step-by-step procedures for disassembling and assembling the product.
CHAPTER 4.ADJUSTMENT
Provides Epson-approved methods for adjustment.
CHAPTER 5.MAINTENANCE
Provides preventive maintenance procedures and the lists of Epson-approved lubricants and
adhesives required for servicing the product.
CHAPTER 6.APPENDIX
Provides the following additional information for reference:
- Wiring Diagram
- Panel Menu Maps
CHECK
P O I N T
SC-F7000 Series/SC-B7000 Series were designed based on SC-S30600 series. The most of the
mechanical structures and functions are the same as those of SC-S30600. This manual provides
only the differences from SC-S30600 series and omits descriptions common to SC-S30600.

Confidential
Symbols Used in this Manual
Various symbols are used throughout this manual either to provide additional information on a specific topic or to warn of possible danger present during a procedure or an action.
Be aware of all symbols when they are used, and always read NOTE, CAUTION, or WARNING messages.
Indicates an operating or maintenance procedure, practice or condition that is necessary to keep the product’s quality.
Indicates an operating or maintenance procedure, practice, or condition that, if not strictly observed, could result in damage to, or destruction of, equipment.
May indicate an operating or maintenance procedure, practice or condition that is necessary to accomplish a task efficiently. It may also provide additional
information that is related to a specific subject, or comment on the results achieved through a previous action.
Indicates an operating or maintenance procedure, practice or condition that, if not strictly observed, could result in injury or loss of life.
Indicates that a particular task must be carried out according to a certain standard after disassembly and before re-assembly, otherwise the quality of the components
in question may be adversely affected.
Indicates that lubrication is needed for the parts after disassembly, when doing a maintenance or replacing a part with a new one.
LubricationLubrication

Confidential
Revision Status
Revision Date of Issue Description
A March 14, 2013 First release

SC-F7000 Series/SC-B7000 Series Revision A
7
Confidential
Contents
Chapter 1 PRODUCT DESCRIPTION
1.1 Product Description ............................................................................................ 10
1.2 Basic Specifications ............................................................................................ 12
1.2.1 Basic Specifications ................................................................................... 12
1.2.2 Electric Specifications ............................................................................... 12
1.2.3 Ink Specifications ...................................................................................... 13
1.3 Printing Specifications ........................................................................................ 14
1.3.1 Supported Media ........................................................................................ 14
1.4 Hardware Specifications ..................................................................................... 15
1.4.1 Dimensions and Weight ............................................................................. 15
1.4.2 Installation Room Requirement ................................................................. 15
1.4.3 Part Names ................................................................................................. 16
1.5 Control Panel ...................................................................................................... 19
1.5.1 Setup Menu ................................................................................................ 21
1.5.2 Serviceman Mode ...................................................................................... 28
Chapter 2 TROUBLE SHOOTING
2.1 Overview ............................................................................................................ 31
2.1.1 Preliminary Check ..................................................................................... 31
2.1.2 Troubleshooting Procedure ........................................................................ 32
2.1.3 Procedure after troubleshooting ................................................................. 32
2.2 Remedies for Maintenance Requests .................................................................. 33
2.3 Remedies for Service Call Error ......................................................................... 34
2.4 Remedies for Print Quality Troubles .................................................................. 37
2.4.1 Ink Clogging .............................................................................................. 37
2.5 Trouble on Paper Feeding .................................................................................. 38
2.6 Other Troubles .................................................................................................... 39
2.6.1 Ink End Error ............................................................................................. 39
2.6.2 Wrong ink mixture error ............................................................................ 39
2.7 Trouble on Service Program ............................................................................... 41
2.8 Trouble on NVRAM Viewer .............................................................................. 41
Chapter 3 DISASSEMBLY & ASSEMBLY
3.1 Overview ............................................................................................................ 43
3.1.1 Precautions ................................................................................................. 43
3.1.2 Cautions After Assembling ....................................................................... 45
3.1.3 Orientation Definition ................................................................................ 45
3.1.4 Recommended Tools ................................................................................. 46
3.2 Parts Diagram ..................................................................................................... 47
3.3 Disassembly Flowchart ...................................................................................... 55
3.4 Disassembly and Assembly Procedure ............................................................... 56
3.4.1 Preparation for Servicing ........................................................................... 56
3.4.2 Consumables/Accessories ......................................................................... 57
3.4.3 Housing ...................................................................................................... 58
3.4.4 Electric Circuit Components ..................................................................... 59
3.4.5 Carriage Mechanism/Ink System Mechanism ........................................... 60
3.4.6 Paper Feed Mechanism .............................................................................. 81
3.4.7 Roll Unit .................................................................................................... 82
3.4.8 Reel Unit .................................................................................................... 83
Chapter 4 ADJUSTMENT
4.1 Overview ............................................................................................................ 85
4.1.1 Precautions ................................................................................................. 85
4.1.2 Adjustment Items and the Order by Repaired Part .................................... 86
4.1.3 Adjustment Items ....................................................................................... 96
4.1.4 Tools/Consumables for Adjustments ......................................................... 97
4.1.5 Service Program Basic Operations ............................................................ 98
4.2 NV-RAM BACKUP / NVRAM Viewer ............................................................ 99
4.2.1 NVRAM Read Procedure .......................................................................... 99
4.2.2 NVRAM Write Procedure ......................................................................... 99
4.2.3 NVRAM Viewer Basic Operation ............................................................. 99
4.3 ADJUSTMENTS (Individual) ......................................................................... 100
4.4 ADJUSTMENTS (Sequence) ........................................................................... 101
4.5 Installing Firmware .......................................................................................... 102

SC-F7000 Series/SC-B7000 Series Revision A
8
Confidential
4.6 Image & Test Print ........................................................................................... 102
4.7 Counter Reset ................................................................................................... 102
4.8 References ........................................................................................................ 102
4.9 Initial Ink Charge Flag ...................................................................................... 102
4.10 CR Related Adjustments ................................................................................ 103
4.10.1 CR Belt Tension Check ......................................................................... 103
4.10.2 APG Function Check ............................................................................. 103
4.10.3 CR Scale Check ..................................................................................... 103
4.10.4 CR Active Damper Auto Adjustment .................................................... 103
4.10.5 Manual Uni-D Adjustment .................................................................... 104
4.10.6 Manual Bi-D Adjustment ...................................................................... 105
4.10.7 PG Adjustment ....................................................................................... 107
4.11 Head Related Checks and Adjustments .......................................................... 109
4.11.1 Tube Inner Pressure Reduction .............................................................. 109
4.11.2 Head ID Input ........................................................................................ 109
4.11.3 Nozzle Check ......................................................................................... 109
4.11.4 Cleaning ................................................................................................. 109
4.11.5 Head Inclination Manual Adjustment (CR direction) ........................... 110
4.11.6 Head Slant Manual Adjustment (PF direction) ..................................... 112
4.12 Ink Supply Related Checks and Adjustments ................................................ 114
4.12.1 Switch between Ink Cartridges and Ink Tanks ...................................... 114
4.12.2 Activation of Cleaning Cartridge ........................................................... 115
4.12.3 Ink eject ................................................................................................. 116
4.12.4 Tube Inner Cleaning .............................................................................. 117
4.12.5 Initial Ink Charge ................................................................................... 118
4.13 Media Feed Related Checks and Adjustments ............................................... 119
4.13.1 PF Belt Tension Check .......................................................................... 119
4.13.2 PF Scale Check ...................................................................................... 119
4.13.3 Manual Adjustment for Media Feeding ................................................. 120
4.14 Boards Related Checks and Adjustments ....................................................... 121
4.14.1 Main Board initial setting ...................................................................... 121
4.14.2 RTC&USB ID Input .............................................................................. 121
4.14.3 MAC Address Input ............................................................................... 121
4.14.4 Serial Number Input .............................................................................. 121
4.14.5 Board Replacement Date & Time Setting ............................................. 121
4.15 Other Printer Checks and Adjustments .......................................................... 122
4.15.1 USB Port and Network Communication Check .................................... 122
4.15.2 Suction Fan Adjustment ........................................................................ 122
4.15.3 Panel Setting Reset & Job History Reset ............................................... 122
4.15.4 Panel LCD Operation Check ................................................................. 122
4.15.5 Panel Buttons Operation Check ............................................................. 122
4.15.6 Motor Measurement & Automatic Adjustment ..................................... 122
4.15.7 Rear AD Adjustment ............................................................................. 122
Chapter 5 MAINTENANCE
5.1 Overview .......................................................................................................... 124
5.2 Setting Up/Storing the Printer .......................................................................... 125
5.3 When left unused/transportation ...................................................................... 126
5.3.1 When left unused ..................................................................................... 126
5.3.2 Transportation .......................................................................................... 128
5.4 Exchange Parts ................................................................................................. 130
5.5 Cleaning ............................................................................................................ 132
5.6 Lubrication ....................................................................................................... 136
Chapter 6 APPENDIX
6.1 Block Wiring Diagram ..................................................................................... 138
6.2 Connection Diagram ......................................................................................... 139
6.2.1 Sensors ..................................................................................................... 139
6.2.2 Ink Holder ................................................................................................ 139
6.2.3 CR Unit .................................................................................................... 139
6.2.4 CR drive mechanism ............................................................................... 139
6.2.5 Paper Feed Mechanism/Pump Mechanism .............................................. 139
6.2.6 Roll Unit/Reel Unit .................................................................................. 139
6.3 Panel Menu Map .............................................................................................. 140
6.4 Part names used in this manual ........................................................................ 143
6.5 Exploded Diagram/Parts List ........................................................................... 144

Confidential
CHAPTER
1
PRODUCT DESCRIPTION

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Product Description 10
Confidential
1.1 Product Description
Product configuration
SC-F7000 Series: Sublimation transfer printer
SC-B7000 Series: Watercolor ink printer
Available paper type
Available media width: Max. 1625 mm (64 inch), Min. 300mm (11.8 inch)
Printable width: Up to 1615 mm (Left/Right margin: 5mm)
Paper thickness: Up to 1 mm
Ink configuration
SC-F7000 Series: Sublimation transfer ink
SC-B7000 Series: Watercolor dye ink
CISS
The printer includes a 1.5-liter ink tank. Supplied ink packs allow you to refill the ink
even during printing.
High speed throughput
Media handling
Supports a variety of commercial media (no genuine media available).
Supported roll sizes are as follows:
Note *1: When using optional heavy roll media system
*2: Up to 40 kg for 2-inch core
Supports RIP made by 3rd parties
EPSON driver is not provided for Windows nor for Mac.
Realizes a high degree of usability
Ease of use
Frequently-used menu is assigned to the short-cut keys on the control panel.
Media handling
•Spindleless
•Simplifies the setting of roll paper by assembling the lift levers.
•Supports high-capacity roll paper up to 80 kg by using optional heavy roll
media system.
C A U T I O N
Wear protective eyewear, gloves and mask when refilling ink
tanks or replacing the waste ink bottle.
If ink adheres to your skin, immediately wash it off with plenty
of soap water. Consult a physician if any problem such as
irritation appears.
If ink gets into your eyes, wash immediately with clean water.
Otherwise your eyes could be seriously injured. If you have any
medical condition, consult a physician.
If ink gets into your mouth, wash it well and immediately
consult a physician.
Do not touch the printed media with your hands.
Do not mix the ink with other type ink.
If it is hard to breath when using the printer, ventilate the room
and let in fresh air.
Dispose of the waste ink and printed media according to local
regulations.
Table 1-1. High speed throughput
Mode Printing Mode Number of passes Throughput
Draft 360x720 dpi 1 58.9 m2/h
High Speed 720x720 dpi 2 30.4 m2/h
Production 2 720x720 dpi 3 22.2 m2/h
Production 1 720x720 dpi 4 16.2 m2/h
High Quality 720x1440 dpi 6 11.1 m2/h
High Quality 720x1440 dpi 8 8.2 m2/h
Table 1-2. Media handling
Weight Roll Outer Diameter Paper Core Diameter
Normal Up to 40 kg Up to 250 mm 2 or 3 inch
When using option*1 Up to 80 kg Roll side: Up to 300 mm
Reel side: Up to 250 mm 2 or 3 inch*2

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Product Description 11
Confidential
Improvement of reliability/durability
Head life:
•6,840 billion shots/1 line
•Ink flow rate: 270 L/BK+M
Operating life of the printer: 3 years or 67,500 m2
(64 inches/720x720 dpi/Bi-d)
Figure 1-1. External View

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Basic Specifications 12
Confidential
1.2 Basic Specifications
1.2.1 Basic Specifications
*Nozzle set configuration is;
1.2.2 Electric Specifications
Table 1-3. Basic specifications
Item Specification
Print method On-demand inkjet
Print Head
Number of nozzles 360 nozzles x 2 lines x 4 (colors)
Configuration of nozzles 720 nozzles for each color*
Line width of nozzles 1 inch
Maximum resolution 720 x 1440 dpi
Control code ESC/P Raster
Paper feed method Friction
RAM For Main 512 MB
For Network 128 MB
Interface USB 2.0 HS
Ethernet (100Base-T/1000Base-T)
Temperature
Operating 15 °C to 35 °C
(recommended: 15 to 25 °C)
Storage (before unpacking)
-20 °C to 60 °C
(no more than 120 hours at 60 °C,
within a month at 40 °C)
Storage (after unpacking) -20 °C to 40 °C
(within a month at 40 ℃)
Humidity Operating 20% to 80% (recommended: 40 to 60%)
(Non condensing)
When storing (packed/unpacked) 5% to 85% (Non condensing)
Row
Product A B C D E F G H I J
SC-F7000 Series C Y M BK - - BK M Y C
SC-B7000 Series C M Y BK - - BK Y M C
Table 1-4. Electric specifications
Item Specification
Rated voltage AC 100 to 240 V
Rated frequency 50 to 60 Hz
Rated current 1.0A to 0.5A
Power
consumpti
on
Printing Approx. 65 W
Ready mode Approx. 20 W
Sleep mode Approx. 9 W
Power off 0.5 W or less
Insulation resistance 10 MΩor more (between AC line and chassis at 500 VDC)
Dielectric strength 1.0 kV rms AC for 1 min. or 1.2 kV rms AC for 1 sec.
(between AC line and chassis)
Leek current 3.5 mA or less

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Basic Specifications 13
Confidential
1.2.3 Ink Specifications
Ink Pack
Cleaning liquid
Cleaning is for servicing only. Packages of the cleaning liquid are only provided as an
ASP.
Waste ink bottle
Removable from the printer when it is filled with approx. 2000ml.
Ink bottle FULL detection is carried out with a software counter.
For the waste ink disposal, conform to the local industrial waste disposal
standards and ordinances in your country.
Table 1-5. Ink Pack
Item Specification
Form Dedicated ink pack (standing pouch)
Ink colors Black system: Black
Color system: Yellow, Magenta, Cyan
Cartridge life See the date printed on the package (at normal temperature)
Guaranteed life
after installation 25 days (from the day that the ink tank was refilled from the ink pack)
Storage
temperature
Uninstalled: -20 to 40°C (within a month at 40 °C)
Installed: -20 to 35 °C (within a month at 40 °C)
Transporting: -20 to 60 °C (within a month at 40 °C, within 72 hours at
60 °C)
Capacity 1000 ml
Dimensions 170 (W) x 272 (L) mm

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Printing Specifications 14
Confidential
1.3 Printing Specifications
1.3.1 Supported Media
PRINTABLE AREA
Note *1: The value selected for [Side Margin (Left)] in the setup menu. The default value is
5mm. Choose a [Side Margin (Left)] over 10 mm when using media holding plates.
*2: The total of the values selected for [Print Start Position] and [Side Margin (Right)] in
the setup menu. The default value is 5mm. Chose a [Print Start Position] or [Side
Margin (Right)] over 10 mm when using media holding plates.
Figure 1-2. Printable area
Table 1-6. Supported Media
Item Specification
Standard Roll Media System Heavy Roll Media System
Roll core size 2 or 3 inch
Roll outer diameter Up to 300 mm
Media width 300 to 1626 mm (64 inches)
Media thickness Up to 1 mm
Roll weight Up to 40 kg Up to 80 kg
5mm
5mm
3-825mm*
2
3-25mm*
1
300-1626mm

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Hardware Specifications 15
Confidential
1.4 Hardware Specifications
This section provides the printer dimensions and shows the main components.
1.4.1 Dimensions and Weight
DIMENSIONS
Figure 1-3. Dimensions
WEIGHT
1.4.2 Installation Room Requirement
Figure 1-4. Installation Room Requirement
Table 1-7. Dimensions
Description Width Depth Height
Stored 2,620 mm 915 mm 1,311 mm
Maximum 2,620 mm 1,259 mm 1,650 mm
Depth
Height
Width
Table 1-8. Weight
Item SC-F7000 Series SC-B7000 Series
Main body 145 kg
Standard Roll Unit 19.5 kg
Standard Reel Unit 21.5 kg (Standard) 21.5 kg (Option)
Legs 32 kg
Optional Heavy Roll Media Feeding Unit (Roll) 18.5 kg
Optional Heavy Roll Media Feeding Unit (Reel) 21.5 kg
Ink tank 3.2 kg
Ink tank unit 4.2 kg
Total weight 225 kg 204 kg

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Hardware Specifications 16
Confidential
1.4.3 Part Names
FRONT SIDE
Figure 1-5. Front Side
Table 1-9. Front side
No. Name
1 Maintenance cover (left)
2 Eject guide
3 Roll core holder
4 Tensioner
5 Roll core holder locking screw
6 Roll support
7 Auto switch
8 Manual switch
9Casters
10 Waste ink bottle holder
11 Adjuster
12 Waste ink bottle
13 Waste ink tube
14 Ink tank
15 Slider
16 Lock lever
17 Chip unit check lamp
18 AC inlet
19 LAN port
20 USB port
21 Maintenance cover (right)
22 Media loading lever
23 Alert lamp
24 Control panel
25 Front cover
Table 1-9. Front side
No. Name

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Hardware Specifications 17
Confidential
SLIDER
Figure 1-6. Front Side
INSIDE
Figure 1-7. Inside
Table 1-10. Slider
No. Name
1 Slider
2 Ink inlet cover
3 Chip unit Table 1-11. Inside
No. Name
1 Print head
2 Media holding plate
3 Cutter groove
4 Pressure rollers
5 Platen
6 Wiper cleaner
7Caps
8Wiper

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Hardware Specifications 18
Confidential
BACK
Figure 1-8. Back
Table 1-12. Back
No. Name
1Driveswitch
2 Roll holder
3 Roll holder fixing screw
4 Lift lever
5 Loading guide
6 Roll support
7 Handle

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Control Panel 19
Confidential
1.5 Control Panel
CONTROL PANEL
Figure 1-9. Control Panel
79
8
6
5
4
3
2
1
13
11
12
10
Table 1-13. Control panel
Name Function
1 Power button Turns the printer ON or OFF.
2 Power light
ON: The power is ON.
Flashing: The printer is receiving data, performing head
cleaning, or other operations during shut-down.
OFF: The power is OFF.
3 Media Setup button Displays the Media Management Menu.
4 Display Displays the printer status, menu, message, etc.
5 Menu button Displays the Setup Menu.
6 Back button Goes back to the previous tier when Setup Menu is
displayed.
7 Left and Right arrow buttons Specifies the entering character position when registering
the setting name or setting IP address in the Setup Menu.
8 Media Feed buttons
Advances/rewinds the media. Hold down button to
advance the media up to 3 m. Hold down button to
rewind the media up to 20 cm.
Selects the menu or the set value while the Setup Menu
is displayed.
9 OK button Determines the items or the settings.
10 button When menus are displayed, closes the menus and goes
back the printer to ready status.
11 Maintenance button Displays the Maintenance Menu.
12 Pause/Cancel button
During printing, pauses the operation.
During setting, finishes the menu and goes back to
printable status.
13 Media Feed button
To advance the printed media to the cut position, press
the button while the printer is printable, then press the
[OK] button.
During printing, performs the Media Feed Adjust
during printing.

SC-F7000 Serie/SC-B7000 Series Revision A
PRODUCT DESCRIPTION Control Panel 20
Confidential
LCD
Display Description
Figure 1-10. LCD
Table 1-14. LCD
Name Function
1Message Printer status, operating status, or an error message is
displayed.
2Media information
From left to right, shows the selected media number,
platen gap, media width, and media remaining.
If a media setting bank number created with this printer is
selected as the print media, the number (from 1 to 30) will
be displayed. When [RIP Settings] is selected, 0 will be
displayed.
The icon of platen gap changes depending on the setting
value as shown below.
: 1.5
: 2.0
: 2.5
The media remaining is not displayed if [Off] is selected
for [Remaining Setup] in the [Media Remaining] menu.
1
2
34
3Chip unit status
The status of the chip unit is indicated as follows.
Ready to print.
An error occurred.
The chip unit could not be recognized or it is not
compatible with the printer. Or, the slider is not
locked.
The chip unit requires replacement.
4 Waste ink bottle status
The status of the wasted ink bottle is indicated as follows.
No problem
Almost full
Full
Table 1-14. LCD
Name Function