Epson SureColor F6200 Service manual

SE Group Confidential (Related Staff Only) Until: Permanent 1
Seiko Epson Corp.
PS CS QUALITYASSURANCE DEPARTMENT
Setting Guide (install)
SureColor F6200 series

SE Group Confidential (Related Staff Only) Until: Permanent 2
Revision Status
Revision Date of Issue Description
0June 26,2015 Temporary release for AMP unit
A July 22,2015 First release for MP unit

SE Group Confidential (Related Staff Only) Until: Permanent 3
•Please inform the user of the next page certainly!
•Please print and pass the next page to user and encourage the points of caution.
IMPORTANCE

SE Group Confidential (Related Staff Only) Until: Permanent 4
Check ink levels
■Ink refill
Ink level is more than 70mm:
Recommends to continue using the
printer until the ink level reaches
70mm from the bottom.
Ink level is about or less than 70mm:
Go to step 2.
13
4
Replace chip unit with
new one attached
new ink pack.
Refill ink.
-Use up all ink in the pack at a time.
(No remaining)
When this message appears,
check ink level of the tank
which is indicated by .
Shake the new ink pack as shown
in the illustration horizontally for
approximately 5cm left and right
for 5seconds approximately
15times.
2
Important

SE Group Confidential (Related Staff Only) Until: Permanent 5
< Caution >
Always wear gloves for assembly to avoid injury from sharp
metal edges.
When handling the ink packs
Wear protective eyewear, gloves, and mask when performing
maintenance.

SE Group Confidential (Related Staff Only) Until: Permanent 6
1-1 Packaging
• Silver ones : 2pcs
• Blue ones : 2pcs
After 100units,
This screws will be changed
(Running change)
First around100units for MP
(applied by Blue marker)
You can use both Blue ones below.

SE Group Confidential (Related Staff Only) Until: Permanent 7
Assembly (Stand)
It is recommended to assemble the stand by a group of three.
Give the screws shown
in the figure a couple of
turns to fasten the
parts temporarily. The
items in the following
steps can not be
attached if the
screws are too tight.

SE Group Confidential (Related Staff Only) Until: Permanent 8
Before using the
printer, be sure
the stand is
fixed in place.
When moving
the printer,
unlock the
casters.
Set the plate to the Stand Right
You must set this plate before placing main unit on the stand. Set hex 2pcs bolts temporarily.
Assembly (Stand)
E x 2

SE Group Confidential (Related Staff Only) Until: Permanent 9
Assembly (Main unit + Stand)
When carrying the printer, use at least 4 persons.
When lifting the printer unit, only hold the highlighted area. Otherwise, it may
affect normal operation and printing.

SE Group Confidential (Related Staff Only) Until: Permanent 10
Assembly (Main unit + Stand)

SE Group Confidential (Related Staff Only) Until: Permanent 11
Setting the Ink Support Assy.
1. Hook the plate into the holes.
2. Tighten 10 screws.
Main unit bottom front side
C x 10
3 hooks 3 holes

SE Group Confidential (Related Staff Only) Until: Permanent 12
1. Loosen 2 screws and make sure the plate is low.
2. Loosen 4 screws and make sure the plates to be able to move up/low and left/right.
Adjust tank height
Loosen Loosen
Loosen
Loosen
Full side Home side

SE Group Confidential (Related Staff Only) Until: Permanent 13
1. Tighten 2 long screws temporarily.
Adjust tank height
Not to
touch
Temporarily tighten Temporarily tighten
2. Make sure the color index on the plate and Put each CSIC on each slider.
3. Set only Cyan and Black Ink Tanks into Ink Holder as the same order as the
color index.
Slider
CSIC
IMPORTANCE
Set the tank with Chip/Slider
during pushing slider.
Full side Home side
Cyan
Black

SE Group Confidential (Related Staff Only) Until: Permanent 14
*** Set to fit between cut position of Ink Tank and hook of Ink Holder.
Please do NOT close cover before adjustment tank height.
Adjust tank height
OK!!
NG!! Set Ink Tank again
IMPORTANCE
1. Tighten 2 Blue screws temporarily.
Temporarily Tighten
No need to fix the tank.
D x 2 (Blue screws)
Temporarily Tighten
Black
Cyan

SE Group Confidential (Related Staff Only) Until: Permanent 15
1. Raise the plate softly and
Tighten 2 screws.
Adjust tank height
2. Insert 2pcs thickness-gauges(2.0mm)
at 2 locations (Black and Cyan)
with raising the tanks.
Tighten
3. Tighten 2 Blue screws to fix the tanks.
(Black and Cyan)
Tighten
To fix the tank
Tighten
To fix the tank
Black
Cyan
Black
Cyan
BlackCyan

SE Group Confidential (Related Staff Only) Until: Permanent 16
Black
Cyan
1. Tighten Right Long Screw until the thickness(2.0mm) gauges can be moved smoothly
at 2 locations(Black and Cyan).
2. Tighten Left Long Screw as the same as the right one.
Adjust tank height – Rough Adjustment
Tighten to adjust
Right Long Screw Left Long Screw
Tighten to adjust
3. Loosen 2 Blue screws a little bit at 2 locations
(Black and Cyan).
Tank
Tank
Tank
There is gap somehow.
loose
Tighten
Reason why to loose 2pcs screws
Loosen Blue screws Loosen Blue screws

SE Group Confidential (Related Staff Only) Until: Permanent 17
1. Tighten Right Long Screw until the thickness(2.0mm) gauges can be
moved smoothly, AGAIN at 2 locations(Black and Cyan).
2. Tighten Left Long Screw as the same as the right one.
Adjust tank height – Detail Adjustment
Tighten to adjust
Right Long Screw Left Long Screw
Tighten to adjust
3. Make sure the thickness gauge(2.5mm) can’t be passed at 2 locations
(Black and Cyan).
Can’t be Passed Can’t be Passed
Thickness
gauge(2.5mm)

SE Group Confidential (Related Staff Only) Until: Permanent 18
Tighten to fix
1. Yellow
Tighten to fix
2. Magenta
D x 2
1. Set the other tanks (Yellow and Magenta).
Adjust tank height
2. Tighten 4 screws to fix the tanks. (Yellow => Magenta => Black => Cyan )
Tighten to fix
3. Black
Tighten to fix
4. Cyan

SE Group Confidential (Related Staff Only) Until: Permanent 19
1. Make sure thickness-gauge(2.0mm) can be passed and
thickness-gauge(2.5mm) can’t be passed AGAIN at 2 locations (Black and Cyan).
Adjust tank height
2.0mm => Can be Passed
2.5mm => Can’t be Passed
2. Check the vertical position
of Ink Tank
3.Check the front and
rear position of Ink Tank.
OK!!
NG!!
Set Ink Tank again
If it is not enough to hold/insert the Ink Tank,
please set this Ink Tank again.
C A U T I O N
NG!!
Set Ink Tank again
OK!!
If it is not enough to hold/insert the Ink Tank,
please set this Ink Tank again.
C A U T I O N

SE Group Confidential (Related Staff Only) Until: Permanent 20
1. Tighten 2 screws.
Adjust tank height
Tighten
Tighten
3. Tighten 2 more screws without pushing
by hand.
2. Push 4 tanks by hand softly.
Tighten Tighten
Full side Home side