Kauber BLUE LABEL User manual

w w w . k a u b e r . e u
-1-
PROJECTION SCREEN
INSTALLATION GUIDE
BLUE LABEL

w
w
w
.
k
a u
-2-
b
e
r
.
e
u

w
w
w
.
k
a u
-3-
b
e
r
.
e
u
IMPORTANT!!!
INSTALLATION AND OPERATION NOTES
1. The cassette and the bottom bar of the screen are protected against damage by polyurethane foam.
Remove the foams protecting the bottom bar after mounting the screen.
2. The screen should be installed in a location away from moisture and strong sunlight.
3. A properly mounted screen must be absolutely levelled.
4. Use a soft, moistened cloth for cleaning. Do not use active cleaners. Protect the screen from ingress of
water or other liquid inside. After cleaning, the screen should be carefully wiped to remove any
residual moisture.
5. DIMENSIONAL TOLERANCE: Projection surface: ± 20mm; components ± 3mm
6. The screen / elevator cannot have connected more than one remote control at once.
7. One remote control (for ex. RC01 / RC02 / Trigger 12V / Trigger230V / IR Receiver / RS Receiver,
etc.) cannot be connected at once to more than one screen, elevator, roller-blind, etc. Such connection
can only be made by using the SG-2 group controller.
Package contents:
Qty.
Projection screen
1 pcs
Mounting bracket
2 pcs
Screws for the bracket
8 pcs
Expansion dowel Ø10
4 pcs
M6 washer
4 pcs
Wrench for adjusting the end positions of the screen
1 pcs
Wall key switch (available for screen without a built-in radio control)
1 pcs
Blue Label is a series of electric projection screens in anodized aluminum housings. A timeless
design and a wide selection of projection surfaces make it the most-chosen screen for home theater and
conference rooms. In the Tensioned version it is additionally equipped with a special system of tensioners
to get an even more tense projection surface.
Switch
Switch
Screen / elevator
engine
Screen / elevator
engine
Screen / elevator
engine
Controls

w
w
w
.
k
a u
-4-
b
e
r
.
e
u
1. Using the screws (c), attach mounting brackets to the sides of the screen (a) depending on the mounting
method (b) in the wall position (fig. 1a) or ceiling one (fig.1b)
Wall mounting
Fig.1a
Ceiling mounting
Fig.1b
SCREEN INSTALLATION

w
w
w
.
k
a u
-5-
b
e
r
.
e
u
2. Depending on the method of mounting, screw the mounting brackets using the mounting dowels
to the wall (Fig.2a) or to the ceiling (Fig.2b).
NOTE! The mounting dowels provided in the set can be used only for ceilings and walls made of solid
materials (for ex. concrete, suporex). When attaching the screen to materials other than those listed,
choose appropriate mounting dowels.
Wall mounting
Fig.2a
Ceiling mounting
Fig.2b

w
w
w
.
k
a u
-6-
b
e
r
.
e
u
3. The delivered screen has end positions set in accordance with the order. If the surface of the screen
scrolls too low or not enough, correct the bottom end position using the included wrench (fig.3). Before
adjustment, check in the warranty card which type of engine your screen is equipped with.
NOTE! Adjustments to the end positions can only be made by a qualified person. All adjustments are
made at your own risk. In the event of an inaccurate adjustment, the screen may get damaged, which is
not covered by the terms of the warranty.
Access to the end stop
Fig.3
4. In Blue Label Tensioned screens - once the surface is fully unfolded, you can use the allen key to adjust
the tensioning force (if necessary) with the screws located on both sides of the bottom bar.
White end stop
Yellow end stop
Access to the
end stops
Access to the
end stops

w
w
w
.
k
a u
-7-
b
e
r
.
e
u
Adjusting the end positions (engine type "C" –you can check the engine type in
the warranty card )
-Correcting the top end position (white end stop).
Fig.4
-Correcting the bottom end position (yellow end stop).
Fig.6
Fig.7
Fig.5
White end stop
White end stop
Yellow end stop
Yellow end stop

w
w
w
.
k
a u
-8-
b
e
r
.
e
u
Adjusting the end positions (engine type "B" and "B-RTS" - check the engine type in
the warranty card))
- Correcting the top end position (white end stop).
Fig.8
Fig.9
- Correcting the bottom end position (yellow end stop).
Fig.10
Fig.11
White end stop
White end stop
Yellow end stop
Yellow end stop

w
w
w
.
k
a u
-9-
b
e
r
.
e
u
End positions adjustment (screen with built-in radio control –engine type "C-RTS")
Correcting the bottom end position:
1. Using the remote control button UP set the roller-blind in the top end position.
2. At the same time, press and hold for more than 5 seconds buttons UP and DOWN. The drive
moves briefly up / down.
3. Using the buttons UP, DOWN, STOP, set the roller-blind in the new end position.
4. Press and hold the button STOP for more than 2 seconds The drive moves briefly up / down
Fig. 12
Correcting the bottom end position:
1. Using the remote control button DOWN set the roller-blind in the bottom end position.
2. At the same time, press and hold for more than 5 seconds buttons UP and DOWN. The drive
moves briefly up / down.
3. Using the buttons UP, DOWN, STOP, set the roller-blind in the new end position.
4. Press and hold the button STOP for more than 2 seconds The drive moves briefly up / down
Fig.13

w
w
w
.
k
a u
-10-
b
e
r
.
e
u
NOTE!
The screen may only be connected to the power supply by a person with appropriate electrical qualifications.
Before installing the screen cassette, lead the power supply cable to the place of installation and then connect it
to the screen during installation according to the diagram A (Fig.14A) or according to the diagram B in the case
of a screen with built-in radio control (Fig.14B).
.
Fig. 14A
DIAGRAM B (built-in radio control)
Fig.14B
DIAGRAM A
ELECTRICAL CONNECTION
Phase
Zero
Earthing
Black
Brown
Blue
Yellow-green
Screen engine
Key switch
Phase
Zero
Earthing
Brown
Blue
Yellow-green
Screen engine

w
w
w
.
k
a u
-11-
b
e
r
.
e
u
Connecting a key switch from the set.
(The switch is available in the set for screen without a built-in radio control)
Fig.15

w
w
w
.
k
a u
-12-
b
e
r
.
e
u
Diagram of connecting a key switch to the screen (screens with a "B" and "C" type
engine)
Fig.16
Contact Description Color
Phase (L)
Zero (N)
Earthing
Brown
Blue
Yellow-green
Black
Brown

w
w
w
.
k
a u
-13-
b
e
r
.
e
u
Housing dimensions:
BLUE LABEL
A- surface width
B- surface height
F = A+64mm
J=A+30mm
K=50mm
H=105mm
G=A+112mm
M=A+88mm
N=60mm
BLUE LABEL + BLACK FRAME
A- width of active surface
B - height of active surface
C = A +100mm
D=B+100mm
F=A+164mm
J=A+130mm
K=50mm
H=105mm
G=A+212mm
M=A+188mm
N=60mm
TECHNICAL DATA

w
w
w
.
k
a u
-14-
b
e
r
.
e
u
BLUE LABEL + BLACK FRAME + BLACK
STRIP
A- width of active surface
B - height of active surface
C = A +100mm
D = B+50mm + height of the black strip
F = A +164mm
J=A+130mm
K=50mm
H=105mm
G=A+212mm
M=A+188mm
N=60mm
BLUE LABEL + TENSIONERS
A- width of active surface
B - height of active surface
C = A +100mm
D=B+100mm
F=A+316mm
J=A+270mm
K=50mm
H=105mm
G=A+368mm
M=A+340mm
N=60mm
BLUE LABEL + TENSIONERS + BLACK STRIP
A- width of active surface
B - height of active surface
C = A +100mm
D = B +50mm + black strip height
F = A +316mm
J=A+270mm
K=50mm
H=105mm
G=A+368mm
M=A+340mm
N=60mm

w
w
w
.
k
a u
-15-
b
e
r
.
e
u
Technical specifications:
Power supply: 230V 50Hz
Power: 120W –screen without a built-in radio control
120W –screen with built-in radio control

w
w
w
.
k
a u
-16-
b
e
r
.
e
u
Thank you for choosing the KAUBER screen.
We invite you to purchase other KAUBER products