Remaco TEN XXL User manual

Warning
Upper Limit
Screen Frame
+-
More Less -
UP
Installation Guide / Manual - TEN XXL Screen
CCOPYRIGHTS 1998 REMACO TECHNOLOGIES PTE LTD Website: www.remacotech.com
V: 13.0
TEN(XXL)
All products are thoroughly inspected and fully tested operational in factory.
We accept no liability whatsoever for any losses due to improper operation, or any unauthorized alternation.
All trademarks contained in this installation guide are the property of their respective owners.
Threaded
rod
Ceiling Suspension
with Threaded rod
Truss Mount
Chain down
Ceiling Suspension
with chain
Chain
300mm
260mm
226mm
Truss
Shackle
MPC-852 Motor/Power Controller
with Radio Frequency Receiver
Accessories Included:
AVA-316-RF 15-Ch
Radio-Frequency Remote
Setting
button
Front Back
AVA-200+
Touch-Contact Switch
Front Back Surface Box
Front View PCB

Controlled
Equipments
Connect to a 230V power supply.
Power
ApplicationConnection
For connection to up to 2 electrical motor powered equipments capable of
bi-directional movements.
Projector Screen
Wiring Diagram
Screen Width
* For details dimension of the screen, please refer to technical specifications at
www.remacotech.com
Ethernet
Connector
Earth
Live
Neutral
AC
Channel 1
Learning Button
Switch power supply
AC85V ~ 240V
Power LED (D1)
Channel 2
Learning Button
Neutral
Down 1
Up 1
Motor 1
Neutral
Down 2
Up 2
Motor 2
Down 1
Stop 1
Up 1
COM
Down 2
Stop 2
Up 2
COM
Contact Closure
A/V Control System
(e.g. AMX / Creston)
AVA-200
Optional
(D.C. Input Only)
AVA-200
UP
DOWN
STOP
UP
DOWN
AVA-200+
AVA-200+
Optional
(D.C. Input Only)
or
AVA-316
15-Channel
RF Remote
(Optional)
>
_
>
>
>
Projector
Lift
LAN
Cable
AC
input
AC Power
Input
E L N
Earth (Green)
Live (Red)
Neutral (Blue)
Neutral(Blue)
Down(Black)
Up(Brown) Neutral(Blue)
Down(Black)
Up(Brown)
Projector Lift
Motor 1 Motor 2
N D1 UP1 N D2 Up2

1D 1S 1U COM COM2D 2S 2U
Up
+
+
....
Down
Stop
Com
+-
+-
DOWN
UP
Contact Closure
(Momentary)
Connection Application
For control by an A/V control system (e.g. AMX or Creston) or a Touch-Contact
Switch (Remaco AVA-200+)
* For this zero voltage Contact Closure, any DC voltage exceeding 3V might
damage the MPC
* Works on momentary contact closure only. (Dry contact, normally open)
To set screen to your desired “up” and “down” positions.
Bottom View
Adjust “ - ” : screen roll away from frame (anti-clockwise)
screen roll into the frame (clockwise)Adjust “ + ” :
STOP
Allen Key (# 4mm) to set
limit switch knob
Upper Limit
Lower Limit
Adjust “ - ” : less screen drop (anti-clockwise)
Adjust “ + ” : more screen drop (clockwise)
Screen Frame
Lower Limit
Red Knob
Upper Limit
White Knob
Common(Orange)
Up(Purple)
AVA-200+
Important Note
The upper limit and lower limit of the screen had been preset in factory. Any adjustment to these 2 limit
switches may cause damages to the screen fabric. If adjusted, it will cause the following problems:
a) The screen will roll into the frame and stop by force and not by the Upper Limit switch.
This will cause overheating of motor which unable the screen to operate properly.
b) The depression of the bottom bar onto the fabric will cause horizontal mark on screen surface.
c) Adjusting the Lower Limit of the screen any lower than beyond the STOP sticker may cause the fabric
to drop off
Disclaimer
Any adjustment to these 2 limit switches will void the warranty for the screen and Remaco will hold
no responsibility for any damages to it. Please consult us if it is necessary to do any adjustment to the
limit switch.
To set screen to your desired “up” and “down” positions.
Stop(Grey)
Down(Pink)

End
Details action and observation:
Connect motors and
power to MPC according
to diagram.
Switch on
power supply
Press and hold the
learning button,
do not release.
Motor will
step-move up
and down
Set AVA -316 RF
remote to CH “1”
Press the
“UP” button
1. Connect motors and power to MPC according to diagram.
2. Switch on power supply.
3. Press and hold the learning button, do not release. Motor will step-move up and down
4. Wait for LED to start flashing, and then release holding the Learning Button .(Wiring Diagram - Page 2)
5. To pair motor 1, set the channel at the AVA-316 RF remote to “1”.
6. Press the “UP” button. Motor 1 will step-move up and down. LED stops flashing. AVA-316 RF remote CH1 is now paired with
motor 1.
7. To pair motor 2, repeat above step 1 to 6
** If nothing is pressed within 20 seconds, motor will revert back to working mode automatically with a step move up and down.
Pairing MPC-851 with AVA-316-RF 15 Ch
MPC-851 compatible with AVA-316 15-Channel Radio Frequency Remote
Stop button
Down button
Channel - Channel +
LCD screen
Up button
AVA-316-RF 15Ch
OPTION 1
Setting Number of Channels Used AVA-316 15-Channel RF Remote
OK
Setting
is OK
5C15 8
Press
Channel ‘<’ & ‘>’
together
The screen
will display C
The screen
will display 15
Press
Channel ‘<’ & ‘>’
together
Select the number of channel required
Example ‘2’ by pressing
‘<’ or ‘>’ Stop X1
The screen
will display 0
Or
15
LED starts
flashing
Release
holding the
learning button
Motor will
step-move
up and down
LED stops
flashing
AVA-316 RF remote CH “1”
is now paired with motor 1
OPTION 2 Control by Network IP Address
Connecting to Network IP
• Connect MPC-852 to the local Ethernet connection
• Connect PC or Laptop or Mobile to LAN or WiFi.
Must be connected to the same network.
• Go to browser (Google Chrome recommended)
• Type in the initial IP Address is 192.168.1.200
• Login Details
User name: admin
Password: mpc852
For more information (Website):
www.remacotech.com > Downloads > Installation Guides > Remote Controls, Electronics & Accessories > MPC-852