Equinox Systems EQLED013 User manual

EQUINOX
SLENDOR BEAM WHITE
User Manual
EQLED013
Contents
1. Safety Instructions
2. Features & Specifications
3. How To Set The Unit
4. Troubleshooting
5. Fixture Cleaning

1. Safety Instruction
WARNING
Please keep this User Guide for future consultation. If you sell the unit to
another user be sure that they also receive this.
Unpack and check carefully that there is no transportation damage before
using the unit.
Before operating, ensure that the voltage and frequency of the power
supply match the power requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to
avoid electric shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least
50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.
Disconnect the mains power before replacement or servicing.
Make sure there are no flammable materials close to the unit while
operating as they may cause a fire hazard.
Always use a safety cable when installing this unit. Do not carry the unit
with its head only, always carry it using the base.
The maximum ambient temperature is: 40℃. Don’t operate it where the
temperature is higher than this.
In the event of a serious operating problem stop using the unit
immediately. Never try to repair the unit by yourself. Repairs carried out
by unskilled people can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center. Always use the same type
spare parts.
Do not touch any power cables during operation as the high voltage may
cause an electric shock.
Warning
To prevent or reduce the risk of electrical shock or fire, do not expose the
unit to rain or moisture.
Do not open the unit within five minutes after switching off.
The housing and lenses must be replaced if they are visibly damaged.
Installation
The unit should be mounted via its screw holes onto the bracket. Always
ensure that the unit is firmly fixed to avoid vibration and slipping while
operating. Make sure that the structure to which you are attaching the unit
to is secure and is able to support a weight of 10 times of the unit’s weight.
Always use a safety cable that can hold 12 times of the weight of the unit
when installing the fixture.
The equipment must be installed by professionals and it must be installed
in a place where is out of the reach of people and no one can pass by or
under it.
2. Features & Technical Specifications
◇Control: Sound active, auto, Master/slave and DMX-512 modes
◇DMX Channels: 1CH/7CH
◇Electronic dimming: 0-100%
◇Compact size and light-weight
Voltage: 100V~240V, 50/60Hz
Fuse: T 2.5A
Power consumption: 23W
Light source: 1 x 10W white led
Dimension: 270 x 160 x 110mm
Weight: 2.5 kg
Pan/Tilt: 540°/180°
Power sockets: IEC
XLR sockets: 3-pin XLR IN/OUT
Please read the instructions carefully as they include important
information about installation, usage and maintenance.

3. How To Set The Unit
3.1 Control panel
Display
Shows the various menus and selected functions
Button
MENU
Selects the programming functions
UP
To go forward in the selected functions
DOWN
To go backward in the selected functions
ENTER
Confirms the selected functions
Mains input
Connection to the power supply.
DMX input/output
For DMX 512 linking. Use a 3-pin XLR cables to link to the controller or to
other units.
3.2 Main Functions
To select any of the given functions, press the MENU button up to where the
required function is showing on the display. Select the function by pressing
the ENTER button and the display will blink. Use the DOWN and UP
buttons to change the mode. Once the required mode has been selected,
press the ENTER button to confirm. To go back to the functions without any
changes, press the MENU button again. Press and hold the MENU button
for one second or wait for one minute to go back to the main menu.
The main functions are as below:
Menu
ADDR
001-512
CHND
1CH/7CH
SLND
MAST
SL1
SL2
SHND
SH1
SH2
SH3
SH4
SOUN
ON
OFF
SENS
000-100
LED
ON
OFF
DISP→INVERT
PAN INVERT
NO
YES
TILT INVERT
NO
YES
TEST
VER
RSET

DMX Address Setting
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to choose the address to
confirm. To go back to the functions without any changes press the MENU
button again. Press and hold the MENU button for one second or wait for
one minute to go back to the main menu.
Channel Mode
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the (1
Channel) or (7 Channel) mode. Once the mode has been selected,
press the ENTER button to confirm. To go back to the functions without any
changes press the MENU button again. Press and hold the MENU button for
one second or wait for one minute to go back to the main menu.
Master Mode or Slave Mode
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
(Slave 1), (Slave 2) or (Master) mode. Once the mode has
been selected, press the ENTER button to confirm. To go back to the
functions without any changes press the MENU button again. Press and
hold the MENU button for one second or wait for one minute to go back to
the main menu.
Show Mode
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
(show 1) or (show 2) or (show 3) or (show 4) mode.
Once the mode has been selected, press the ENTER button to confirm. To
go back to the functions without any changes press the MENU button again.
Press and hold the MENU button for one second or wait for one minute to go
back to the main menu.
Sound Mode
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
(sound on) or (sound off) mode. Once the mode has been selected,
press the ENTER button to confirm. To go back to the functions without any
changes press the MENU button again. Press and hold the MENU button for
one second or wait for one minute to go back to the main menu.
Sound Sensitivity
Press the MENU and use the UP and DOWN buttons to select and
select the sound sensitivity between value 0 and 255. Press the ENTER
button for confirmation after value selection. To go back to the functions
without any changes press the MENU button again.
Led Display
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the (Led
display on) or (Led display off) mode. Once the mode has been
selected, press the ENTER button to confirm. To go back to the functions
without any changes press the MENU button again. Press and hold the
MENU button for one second or wait for one minute to go back to the main
menu.
Display Inversion
Press the MENU button to select . Press the ENTER button to change

the mode (display normal), It will be automatically saved after 8
seconds. Press the ENTER button again to select the mode (display
inversion). To go back to the functions press the MENU button. Press and
hold the MENU button for one second or wait for one minute to go back to the
main menu.
Display normal mode is for floor standing the unit.
Display inversion mode is for hanging the unit upside down.
Pan Inversion
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
(normal) or (pan inversion) mode. Once the mode has been selected,
press the ENTER button to confirm. To go back to the functions without any
changes press the MENU button again. Press and hold the MENU button for
one second or wait for one minute to go back to the main menu.
Tilt Inversion
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
(normal) or (tilt inversion) mode. Once the mode has been
selected, press the ENTER button to confirm. To go back to the functions
without any change press the MENU button again. Press and hold the
MENU button for one second or wait for one minute to go back to the main
menu.
Auto-Test
Press the MENU button to select . Press the ENTER button and the
unit will run a self-test with its built-in programs. To go back to the functions
without any changes press the MENU button again. Press and hold the
MENU button for one second or wait for one minute to go back to the main
menu.
Reset
Press the MENU button to select . Press the ENTER button and all
channels of the unit will return to their standard position.
4. How To Control The Unit
1. Master/slave built-in preprogram function
2. Universal DMX controller
There is no need to turn the unit off when you change the DMX address as
new DMX address setting will be effected at once. Every time you turn the
unit on, it will show “ ”on the display and move all the motors to their
‘home’ position and you may hear some noises for about 20 seconds. After
that the unit will be ready to receive a DMX signal or run the built in
programs.
4.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the
other units to give an automatic, sound activated, synchronized light show.
This function is good when you want an instant show. You have to set the
first unit as master and select show 1, show 2, show 3 or show 4 from
the Show Mode. The other units must be set to either Slave 1 (normal) or
Slave 2 (2 light show) mode. A DMX cable between the units for daisy
chaining is needed.
2-light show
In slave mode, Slave 1 means the unit works normally and Slave 2
means 2-light show. In order to create a great light show, you can set Slave
2on the second unit to get contrast movement to each other, even if you
have two units only.

4.2 DMX Controller
By using a universal DMX controller to control the units, you will need to set
a DMX address from 1 to 512 so that the units can receive a DMX signal.
Press the MENU button until is showing on the display. Press the
ENTER button and the display will blink. Use the DOWN and UP buttons to
change the DMX-512 address. Once the address has been selected, press
the ENTER button to confirm. To go back to the functions without any
changes press the MENU button again. Press and hold the MENU button
one second or wait for one minute to go back to the main menu.
Please refer to the below diagram to address your first 4 units：
Channel
mode
Unit 1
Address
Unit 2
Address
Unit 3
Address
Unit 4
Address
1 channel
1
2
3
4
7 channel
1
8
15
22
4.3 DMX 512 Configuration
1 CHANNEL MODE:
Channel
Value
Function
1
000-007
Blackout
008-067
Show 1
068-127
Show 2
128-187
Show 3
188-255
Random shows
7 CHANNEL MODE:
4.Troubleshooting
Following are a few common problems that may occur during
operation and some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of the power and the main fuse.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX cables to see if linked
correctly.
2. If the DMX address is showing but no response to the controller, check
the address settings and DMX polarity.
3. Try another DMX controller.
C. No response to the sound
1. Make sure the unit is not receiving a DMX signal.
Channel
Value
Function
1
0-255
Pan
2
0-255
Tilt
3
0-255
PAN/TILT Speed
(slow-fast)
4
0-255
Dimmer
5
0-255
Strobe(slow-fast)
6
0-255
NO FUNCTION
7
0-010
NO FUNCTION
011-255
Sound

2. Check the microphone to see if it is good by tapping it. The microphone
is located on the bottom plate of the unit.
5. Fixture Cleaning
The cleaning of external optical lenses must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding
can cause a greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning fluid or mild soapy water.
Always dry the parts carefully.
Clean the external optics at least every 20 days.
---------------------www.prolight.co.uk----------------------------------