Equinox Systems Power Par Series User manual

Order codes:
Power Par 36 - EQLED112
Power Par 54 - EQLED113
Power Par Series
User Manual

www.prolight.co.uk Power Par Series User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Oneyearfromdateofpurchase.

www.prolight.co.uk Power Par Series User Manual 3
Product overview & technical specications
Theseextremelypowerfulxturesfeature3Wtri-colourLEDsandproduceavariedrangeofeffectsincluding
colourchangeandfadeeffectscontrollableinautoandsoundactivemodesalongwithDMX.Adualbracketis
includedallowingthexturetobehungorstoodontheoor.
Power Par 36
Power Par 54
• 36x3Wtri-colourLEDs
(RGB)
• Beamangle:25°
• 1459Lux@2m(fullon)
• DMXchannels:6
selectable
• Auto,soundactiveand
master/slavemodes
• 0-100%dimmingand
variablestrobe
• 4pushbuttonmenu
withLEDdisplay
• Bracketallowsformultiple
riggingoroorstanding
applications
• IECpowerinput/output
• 3-PinXLRinput/output
• Fancooled
• 54x3Wtri-colourLEDs
(RGB)
• Beamangle:25°
• 2530Lux@2m(fullon)
• DMXchannels:6
selectable
• Auto,soundactiveand
master/slavemodes
• 0-100%dimmingand
variablestrobe
• 4pushbuttonmenu
withLEDdisplay
• Bracketallowsformultiple
riggingoroorstanding
applications
• IECpowerinput/output
• 3-PinXLRinput/output
• Fancooled
Power Par Series
Specications Power Par 36
Powerconsumption 110W
Powersupply 100~240V,50/60Hz
Fuse F3A250V
Dimensions 290x265x100mm
Weight 1.5kg
Ordercodes EQLED112
290mm
265mm 100mm
MENU DOWN
FUSE: F3A 250V
POWER INPUT/OUTPUT:
100~240V, 50/60Hz
DMX INPUT
DMX OUTPUT
UP ENTER
POWER PAR
www.prolight.co.uk
01
06
01
03
04
05
08
09
07
02
10
02
01-Hangingbracket
02-Hangingbracket
adjustmentknob
03-LEDdisplay
04-Functionbuttons
05-IECpowerinput
06-IECpoweroutput
07-Fuse:F3A250V
08-3-PinDMXinput
09-3-PinDMXoutput
10-Fan
Inthebox:
1 x xture,
1 x power cable
& 1 x user manual
Specications Power Par 54
Powerconsumption 165W
Powersupply 100~240V,50/60Hz
Fuse F3A250V
Dimensions 290x265x100mm
Weight 1.5kg
Ordercodes EQLED113

www.prolight.co.uk Power Par Series User Manual 4
Operating instructions
DMX mode:
OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes
tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthe
xtureandeachxtureindependently.
ToaccesstheDMXaddressmode,pressthe“MENU”buttononthefrontoftheunittoshowA001
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
requiredDMXaddress.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
RGB colour mix mode:
Inthismodeyoucansetthexturetoanycolourandanybrightness.
Toaccessthecolourmixmodepress“MENU”untilthedisplayshowsPr--ontheLEDdisplay.
Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectPr00.
Pressthe“ENTER”buttontoshow r---with3digitsafterontheLEDdisplay.
Pressthe“ENTER”buttontoconrm.
Therrepresentsred,G=greenandb=blue.
The3digitsafterarethebrightnesssettingfrom000~255.
For example:
Ifyousetr,G,balltozero,yourunitwillhavenoLEDslitup(blackout).
Ifyousetr000tor255andGandbtozero,yourunitwillshowonlyredLEDs.
Pressthe“ENTER”buttontoconrmthesettingandmovetothenextcolour.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
6 channel mode:
Channel Value Function
CH1 000-255 Reddimmer(0-100%)
CH2 000-255 Greendimmer(0-100%)
CH3 000-255 Bluedimmer(0-100%)
CH4
000-027 Nofunction
028-055 Strobe(useCH6forspeed)
056-083 Strobewithcolourchange
(useCH6forspeed)
084-111 Red
112-139 Green
140-167 Blue
168-195 Yellow
196-223 Purple
224-251 Cyan
252-255 White
CH5
000 Nofunction
001-012 Redfadein/out
(useCH6
forspeed)
013-025 Greenfadein/out
026-038 Bluefadein/out
039-051 Yellowfadein/out
052-064 Purplefadein/out
065-077 Cyanfadein/out
078-090 Whitefadein/out
091-116 Autocolourfadein/out
117-142 Colourfade
143-168 Colourchange
169-181 Colourchangewithstrobe
182-207 Allautoshows
208-255 Soundactiveash(whenCH6is000)
208-255 Soundactive(whenCH6is001-255)
CH6 000-255 Speed(slow-fast)/Sensitivity(low-high)

www.prolight.co.uk Power Par Series User Manual 5
Built-in program mode:
Toaccessbuilt-inprogrammodepress“MENU”untilthedisplayshowsPr--ontheLEDdisplay.
Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectbetweenPr00~Pr13.
Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectthespeedbetween
SP00~Sp20.Pressthe“ENTER”buttontoconrm.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Sound active mode:
Toaccessthesoundactivemode,pressthe“MENU”buttononthefrontoftheunittoshowSoudon
theLEDdisplay.Nowpressthe“ENTER”buttonandthedisplaywillshowSens.Pressthe“ENTER”
buttonagainandusethe“UP”and“DOWN”buttonstoselectthesensitivitylevelfrom000-100.
Pressthe“ENTER”buttontoconrmthesetting.
Value: 000 - 100 (000 = low,100 = high)
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Master/slave mode:
Tosetthemasterunit,pressthe“MENU”buttonontherearofthemasterunittoselectyour
desiredprogram(soundactiveorRGBcolourmix).
Tosettheotherunitsinslavemode,pressthe“MENU”buttonontherearoftheunittoshowSLav
ontheLEDdisplayandpressthe“ENTER”buttontoconrmthesetting.Theunitswillnowrunin
sequencewiththemasterunit.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Built-inprogrammode
Pr00-Pr13
Pr00-RGBcolourmixmode
r000~r255R
G000~G255G
b000~b255B
Pr01-R
Pr02-G
Pr03-B
pr04-RG
Pr05-RB
Pr06-GB
Pr07-RGB
Pr08-Colourfadein-out(3colours)
Pr09-Colourfadein-out(7colours)
Pr10-Colourfade
Pr11-Colourfadein-out(7colours)&colourfade
Pr12-Colourchange(3colours)
Pr13-Colourchange(7colours)
Slavemode SLAV
Soundactivemode SOUd
Sens
000~100
DMXmode 6CH
Addresssetting A001~A512
Menusystem

www.prolight.co.uk Power Par Series User Manual 6
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Also remember that DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.prolight.co.uk Power Par Series User Manual 7
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterferance.itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk Power Par Series User Manual 8
Operating instructions & WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.