Ergotron WorkFit-P User manual

ERGOTRDn®
WorkFit-P
Sit-stand height adjustable workstation
www.ergotron.com
USA 1-800-888-8458
Europe [phone]
China 86-769-86018920

Important!
You will to adjust this product
product before attempting adjustments. product
and stay where set it If movements are too does not stay in desired positions,
adjustment instructions to create smooth
1,,n1,r;r1mn on your product and adjustment, it
take many turns to a difference. time
the of the load, you should
CAUTION! Max weight 10 lbs (4.5 kg). Do
weight capacity. Serious injury or property
Components
i
1x i
1x
1x
1x (r=!
1x
.2.Smm !
Tools Needed
13mm
from this product, resulting in a change in
to ensure safe optimum operation.
1x '@ ~1x
1x
1x~
~
2x~
M6x14mm
8mm r.s------\\\
1xQ~fJ4"
ix\f •4mm
m

Set-up Steps
1
DESK THICKNESS
~
,.6r. Warning: Bec~use mounting surface materials can
vary widely, it is imperative that you make sure mounting surface
is strong enough to handle. mounted product and equipment.
CLAMP
GROMMET
DESK THICKNESS
0.78"-2.56"(20-65mm)
0.78"-1.78"(20-4Smm} 1.70"-2.56"{43-65mm)
ct==
fe .4mm
Smm~
0 ij________-11) f /4"
r b
C 1x8
1x --·--~
d 1x~1x~
&
• •• · CAUTION: Bolt must be
centered In hole.
0.5"-2.5"

Set-up Steps
2
*
2x~
M6x 14mm
« e4mm
5
4
5
1x 1x
t3' ~
«• 4mm
I
I
3a L___________----rlm::J" ',0 s--------7
b c

Adjustment StJ!p
Important! Yo~ will need to adjust this product after installation is complete.
Make sure all xour equipment is properly installed on the product before
attempting ad~ustments. This product should move smoothly and easily
through the fyll range ofmotion and stay where you set it. If movements are
too easy or difficult or ifproduct does not stay in desired positions, follow the
adjustment in~tructions to create smooth and easy movements. Depending on
your product 9nd the adjustment, it may take many turns to notice a difference.
Any time equi~ment is added or removed from this product, resulting in a
change in the '(veight of the mounted load, you should repeat these adjustment
steps to ensur~ safe and optimum operation.
!
I
- I
Increase Lift Strength
If the mounted weight is too heavy or this product does not stay up
when raised, then you'll need to increase Lift Strength:
a
Decrease Lift Strength
If the mounted weight is too light or this product does not stay
down when lowered, then you'll need to decrease Lift Strength:

Adjustment Step
!
i"
: Increase Friction
-ff • If this product moves too easily fiom side-to-side, then you'll
1
need to increase friction:
' .Ma Decrease Friction
-- • If this product is too difficult to move from side-to-side, then
.
you'll need to decrease friction:
i
I
~
~w
13mm
WARNING! Sto ed Energy Hazard: The arm mechanism is
under tension a d will move up rapidly, on its own, as soon
as attached eq ipment is removed. For this reason, DO NOT
remove equipm nt unless the arm has been moved to the
highest position! Failure to follow this instruction may result
in serious persopal injury and/or equipment damage!
r .2.Smm
z

Features
\ :_ --
L~t Your Workstation to Work For YOU!
Height: Position top of screen slightly below eye level.
Po$ition keyboard at about elbow height with wrists flat.
Di~tance: Position screen an arm's length from face-at least 20" (508mm}.
Po$ition keyboard close enough to create a 90" angle in elbow.
An!lile: Tilt screen to eliminate glare.
TiltTthe keyboard back 10° so that your wrists remain flat.
'
Tq Reduce Fatigue
Breathe - Breathe deeply through your nose.
Bli~k - Blink often to avoid dry eyes.
Break •2 to 3 minutes every 20 minutes
•1 ~to 20 minutes every 2 hours.
For service and warranty visit www.ergotron.com
NOTE: When contacting
Ergotron
about Warranty
find ID Label here.
Si desea informaci6n de servicio y garantfa, visite www.ergotron.com ,
Pour toute question concernant la garantie ou le service client, consultez wijvw.ergotron.com
Weitere lnformationen zu Service und Gewahrleistung erhalten Sie unter www.ergotron.com.
Ga voor service en garantie naar www.ergoton.com '
Per assistenza e la garanzia visitare www.ergotron.com
Ga in pa www.ergotron.com for service och garanti ,
if-t'X;ts~U-f*filH<:".)\, \'"[~L,(l;t www.ergotron.com ~L:''l<f1:;!\,1o
fj;¥;JJ!t%-;f!Jf'ij~, i~ijj(ii) W"'W· ergotron. com
~j--R:/1
8
©101~Ergotron,lnc
J t::l"fCJ4. All rlg,tmserved.
While Ergotron, Inc.makeseveryeffort to provide accurate and complete informJ>ction o~ the installt1tioo
and use of its products, it will not be held liable for any editorial errors: or omissions \indOOing those
made in the process of tra.nslation from En.glish to anothet language), or f.or incid~tal, special or
consequential damages of any nature resulting from furnishing this instruction and rformance of
equipment In connection with this instruction. Ergotron, lnc. reserves the right to ma dlanges in the
product design and/or product documentation without notification to its ~ers. Fort~ most current
product tnformation, or
to know if this document Is available in languages other t~n those herein,
please contactfrgotron. No-part ofthis publication may
be reproduced,stored in a ret ·eval system,or
transmitted
In any form or by any means,elertron!c, mechanical, photocopying, recordi g orotherwise
Without
the prior written con!.>ent of Ergotron, ln<:.,1 t81 irapp i'klad, Eagan, Mlnnes4ita, 55121, USA
Patents Pending and Patented U.S. &Foreign, Ergotron is a registered tr3demark of Ergo ron, Inc
Amed&as Sales and
Corporate Headquarters
St. Paul, MN USA
[phone]
[phone]
www,ergolron.com
[email protected]
APACSales
EMEAsates
Amersfoort, The Nelflerlamls
[phone]
www.ergotron.com
info.eu@el'gotroo.com
Worldwide OEM Sales
Tokyo, Japan www.ergotron.com
www.ergotron.com info.oem®ergotroo.com
[email protected]