Ergotron WORKFIT-DL User manual

of
GrevC•/
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド : 日本語
用户指南 : 汉语
WORKFITDL
Includes
Constant Force™
Technology
" ( mm)
ENGLISH
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide
CAUTION: DO NOT EXCEED
MAXIMUM LISTED WEIGHT
CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
Total Weight Capacity(includes Cable Tray):
Worksurface size
"x" (xcm) lbs. ( kg)
"x" (xcm) lbs. (kg)
Cable Tray Weight Capacity:
 lbs. ( kg)

of
GrevC•/
826-901-00
WARNING
Moving Parts Can Crush And Cut
IMPACT HAZARD
Failure to heed this warning may result in
serious personal injury or property damage!
For More information and instructions visit www.ergotron.com
or contact Ergotron Customer Care at 1-800-888-8458.
Minimize Lift Strength BEFORE:
- Removing Mounted Equipment
and
Insert 4 Stop Screws BEFORE:
- Shipping or Storing (i.e. when Desk is not upright).
To Minimize Lift Strength
Refer to installation manual for instructions on
how to minimize lift strength.
To Insert 4 Stop Screws
Refer to installation manual for instructions on
installing stop screws.
ENGLISH
These symbols alert users of a safety
condition that demands aention. All users
should be able to recognize and under-
stand the significance of the following
Safety Hazards if encountered on the prod-
uct or within the documentation. Children
who are not able to recognize and respond
appropriately to Safety Alerts should not
use this product without adult supervision!
HazardSymbols
Review
Safety
Important!YouwillneedtoadjustthisproductaerinstallationiscompleteMakesureallyourequipment
isproperlyinstalledontheproductbeforeaemptingadjustmentsThisproductshouldmovesmoothly
andeasilythroughthefullrangeofmotionandstaywhereyousetitIfmovementsaretooeasyordifficult
orifproductdoesnotstayindesiredpositionsfollowtheadjustmentinstructionstocreatesmoothand
easymovementsDependingonyourproductandtheadjustmentitmaytakemanyturnstonoticea
differenceAnytimeequipmentisaddedorremovedfromthisproductresultinginachangeintheweight
ofthemountedloadyoushouldrepeattheseadjustmentstepstoensuresafeandoptimumoperation
SymbolSignal Word Level of Hazard
NOTE A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tellsyou how to avoid the
problem.
WARNING A WARNING indicates either potential for property dam-
age, personal injury, or death.
ELECTRICAL
AnElectrical indicates an impending electrical hazard
which, if not avoided, may resultin personal injury, re
and/or death.

of
GrevC•/
WARNING



ENGLISH
Safety
WARNING! TIPPING HAZARD!
When mounting accessories to the WorkFit-D, they must stay
within the foot print. Do not mount accessories past the front
and rear worksurface! Failure to follow this warning may
result in equipment damage and or personal injury.
WARNING!Stopscrewsarepreinstalledinthisproducttosecureitinthecompressedposition
duringshippingandinstallationDONOTREMOVETHESESCREWSUNTILINSTRUCTEDTODO
SOINTHESEINSTRUCTIONSMakesurethesescrewsareinplacebeforestartinginstallation
Failuretofollowtheseinstructionsmaycauselienginetoexpandrapidlyandmayresultin
equipmentdamageandorpersonalinjuryIfanyofthestopscrewsarenotinstalledinthese
locationscontactcustomercarebeforecontinuingwithinstallation
DONOTREMOVESCREWS!
IMPORTANT!
SavethesestopscrewsandinstructionsInstallstopscrewswhenshippingorstoringthisproduct
Failuretofollowtheseinstructionsmaycauselienginetoexpandrapidlyandmayresultin
equipmentdamageandorpersonalinjury
WARNING!
Keep Brake Cables Away from Sync Rod and Crossbars During Installation!
Failure to keep the brake cables away from sync rod and crossbars may restrict
li motion and may cause equipment damage or personal injury! Refer to
instruction manual for more information.

of
GrevC•/
ABCD
1
2
3
4
5
6
Mxmm Mxmm
mm
x/"
x
x
x x x
14mm
14mm
x
x
x
x
x x
x
x
x
x
x
/"
/"
/"
ENGLISH
Components
ToolsNeeded
WoodScrew

of
GrevC•/

ENGLISH
Placetheworksurfaceonacleanfloorwiththetopsidefacingdown
Carefullypositionthelegwiththehandbrakeonthesideoftheworksurfacewiththebrake
mountingholesandtheotherlegontheothersideoftheworksurface
NOTE: The brake cable is aached to both legs. Take care when removing the legs from the packaging to
avoid damaging or pulling the brake cable from the legs.
Brake mounting holes
Rear Edge of Worksurface
Front Edge of Worksurface

of
GrevC•/

x/"
x
/" /"
/"
Aachcablechannel
ENGLISH
WoodScrew

of
GrevC•/

x/"
x
/" /"
/"
ENGLISH
NOTE: Do not fully insert the screws into the worksurface at this time. Leave approximately 1/8” space.
Looselyaachthelegwiththebrakehandletotheworksurface
WoodScrew

of
GrevC•/

WARNING
ENGLISH
Aachthesyncrodtothelegaachedtotheworksurface
WARNING!
Keep Brake Cables Away from Sync Rod and Crossbars During Installation!
Failure to keep the brake cables away from sync rod and crossbars may restrict
li motion and may cause equipment damage or personal injury! Refer to
instruction manual for more information.

of
GrevC•/

WARNING
ENGLISH
Placetheotherlegontheworksurfaceandaachthesyncrodtoit
WARNING!
Keep Brake Cables Away from Sync Rod and Crossbars During Installation!
Failure to keep the brake cables away from sync rod and crossbars may restrict
li motion and may cause equipment damage or personal injury! Refer to
instruction manual for more information.

of
GrevC•/

x/"
x
/" /"
/"
ENGLISH
Looselyaachtheotherlegtotheworksurface
NOTE: Do not fully insert the screws into the worksurface at this time. Leave approximately 1/8” space.
WoodScrew