ESP Safety IPES Series User manual

ESP SAFETY INC
IPES IR3-AL: Multispectrum IR, Aluminum (Red), P/N 100-0017-01
IPES IR3-SS: Multispectrum IR, Stainless Steel, P/N 100-0016-01
IPES IR/UV-AL: Dual Channel IR/UV, Aluminum (Red), P/N 100-0003-01
IPES IR/UV-SS: Dual Channel IR/UV, Stainless Steel, 100-0010-01
IPES FLAME DETECTOR
IPES FLAME DETECTOR
QUICK INSTALLATION GUIDE
1
COMPONENTS:
2
8
3
45
6
7
The typical IPES delivery set consists of the following components
1. Visor (Qty 1), P/N 125-0005
2. Magnetic Collar (Qty 1), P/N 120-0006 *one provided per 1-10 IPES
3. Mounting Bolts (Qty 4), P/N 125-0019
4. M20 to 3/4” NPT Adapter (Qty 1), P/N 420-0208
5. M20 Threaded Plug (Qty 1), P/N 420-0209
6. Mounting Bracket (Qty 1), P/N 125-0003
7. 4mm Hex Wrench (Qty 1), P/N 120-0077 *one provided per 1-10 IPES
8. IPES Flame Detector (Qty 1)
IR3 (aluminum) P/N 100-0017-01
IR3 (stainless steel) P/N 100-0016-01
IR/UV (aluminum) P/N 100-0003-01
IR/UV (stainless steel) P/N 100-0010-01
The following items for the IPES may be ordered:
Accessories:
Visor, P/N 125-0005
Mounting Hardware, P/N 125-0019
ITES Test Lamp, P/N 120-0007
Magnetic Collar, P/N 120-0006
Contact ESP Safety:
USA
555 North First Street
San Jose, CA 95112
USA
Tel: [phone]
Fax: [phone]
email: [email protected]
PAGE 1 PAGE 2
OVERVIEW
This Quick Start Guide provides basic guidelines for mechanical and
electrical installation of the IPES Flame Detector in preparation for product
startup. For detailed testing, troubleshooting and operation instructions,
refer to the IPES Operating Manual for your model.
The IPES Operating Manual can be downloaded from the ESP Safety
website:
www.espsafetyinc.com
Prior to startup of the IPES Flame Detector, review that the following have
been completed:
Pre Startup Checklist:
1. Verify that the IPES Flame Detector has been properly mounted.
2. Verify that all conduit/cable gland entries have been tightened and
sealed, if necessary
3. Verify that all detector wiring has been installed correctly.
4. Verify that the detector is properly earth grounded.
5. Verify that the detector rear cover is securely fastened.
6. Disconnect or power down all output devices and alarms to prevent false
actuation.

PAGE 6
Adjust detector tilt angle.
1. Remove set screws from adjustment arm.
2. Adjust to desired tilt angle.
3. Replace set screws.
Detector
Mounting
Bracket
Nut & Washer
15°
15°
MECHANICAL INSTALLATION (cont’d):
1. Connect the ame detector to the mounting bracket.
2. Secure with supplied nut & washer
PAGE 4
ELECTRICAL INSTALLATION:
Connect wiring to the IPES terminal blocks. Note: The IPES Flame Detector
requires a 24VDC power source (18-32VDC voltage range)
1. Separate the detector body from the rear cover by loosening the 3
screws using the supplied 4mm hex wrench.
Rear Cover
Detector Body
Screw (3ea)
PAGE 5
2. Connect wiring to the appropriate terminals on the terminal blocks.
Refer to diagram on Page 6 for terminal label and function.
3. When completed, reattach the detector body to the rear cover. Secure
with the supplied screws.
4. Run the earth ground wire to the external ground stud on the detector
cover.
The magnetic test collar may be shipped attached to the IPES body. The
test collar blocks all output signals from the IPES and is to be used only for
functional testing of the detector and removed during normal operation.
Additional wiring details can be found on pages 12-16 of the IPES IR3
Operating Manual or pages 13-15 of the IPES IR/UV Operating Manual
MECHANICAL INSTALLATION:
Attaching to a Horizontal Surface:
Bottom Mount
Top Mount
Mounting Bracket
Mounting Surface
ELECTRICAL INSTALLATION:
IPES Terminal Block
TERMINAL BLOCK LABEL FUNCTION
X3 +24V 24V from system power source
X3 GND System Ground from system power source
X3 +4/20 +4 to20mA current loop output
X3 RS485A RS-485 MODBUS
X3 RS485B RS-485 MODBUS
X3 R_WORK Fault Relay, NC when energized
X3 R_WORK Fault Relay, NC when energized
X4 +24V Output to next device if required
X4 GND Output to next device if required
X4 -4/20 -4 to20mA current loop output
X4 RS485A Output to next device if required
X4 RS485B Output to next device if required
X4 R_FIRE Alarm Relay, NO when energized
X4 R_FIRE Alarm Relay, NO when energized
Attaching to a Vertical Surface:
Secure mounting bracket to a stable surface.
PAGE 3
Additional wiring details can be found on pages 12-16 of the IPES IR3
Operating Manual or pages 13-15 of the IPES IR/UV Operating Manual
Additional mounting details can be found on pages 11-12 of the IPES IR3
and IPES IR/UV Operating Manuals
Additional mounting details can be found
on pages 11-12 of the IPES IR3 and
IPES IR/UV Operating Manuals