ETC echoflex ELED1 User manual

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC) ELED1
Corporate Headquarters nMiddleton, WI, USA |[phone]
Web echoflexsolutions.com |Email [email protected] |Support [email protected]
©2022 Echoflex Solutions, Inc. Trademark and patent info:echoflexsolutions.com/ip
Product information and specifications subject to change.
Echoflex intends this document to be provided in its entirety.
8189M2100 Rev D Released 2022-08
Overview
The LED Fixture Controller (120-277 VAC) (ELED1) provides wireless
control of an individual fixture or single zone lighting based on
occupancy state, manual switch action, ambient light levels, and gateway
commands.
ELED1-DUN
ELED1-DUS
This document covers installation of all the ELED1 models. The Echoflex
LED Fixture Controller ELED1(H) Configuration Guide is available for
download at echoflexsolutions.com.
The product package includes the controller, installation guide, and
mounting strap (for ELED1-DUS model).
Prepare for Installation
To ensure optimal function, consider the installation environment and the
following guidelines:
•
Avoid spaces with high density construction materials and large
metal appliances or fixtures as they may disrupt wireless reception.
•
For optimal performance, switches and sensors should be installed
within a 24 m (80 ft) unobstructed view of the controller. Consider
adding a repeater to extend the wireless signal, if required.
•
Mount the controller to an electrical junction box (preferably non-
metallic) or a panel in a location and at a height where it is not
subject to tampering by unauthorized personnel.
•
Make sure the antenna wire is unrestricted and not in contact with
any metal surface.

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
Supplies required to install the controller (not provided):
•
Appropriately sized wire nuts
•
Wire insulation and small cable ties
•
Two 3/8 inch #8 metal screws (for surface mounting strap only)
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
WARNING: RISKOFELECTRICSHOCK! This device utilizes
high voltage and should only be installed by a qualified
installer or electrician. Follow all local codes for
installation. Before terminating the AC power wiring verify
that the main breaker is in the off position and follow the
proper lockout/tag out procedures required by NFPA
Standard 70E.
AVERTISSEMENT : RISQUE DE DÉCHARGE ÉLECTRIQUE!
Cette appareil utilise une haute tension et ne doit être
installé que par un installateur qualifié ou un électricien.
Suivez tous les codes locaux pour l'installation. Avant de
raccorder le câblage du courant alternatif, vérifiez que le
disjoncteur principal est en position d'arrêt et suivez les
procédures de Consignation/Déconsignation prescrites par
la norme NFPA 70E.
WARNING: For indoor use only! Must install to an
electrical junction box or wireway.
AVERTISSEMENT : Uniquement pour usage d'intérieur!
Doit être installé sur une boîte de raccordement électrique
ou un chemin de câbles.
•
This product is suitable for use in dry locations where the ambient
temperature is -10°C to 60°C (14°F to 140°F).
•
Do not use outdoors.
•
Do not mount near gas or electric heaters.
•
Equipment should be mounted in locations and at heights where it is
not subject to tampering by unauthorized personnel.
•
The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
•
Do not use this equipment for other than its intended use.
•
Servicing should be performed by qualified service personnel.
•
Pollution Degree: 2.
SAVE THESE INSTRUCTIONS
LED Fixture Controller (120-277 VAC) Page 2 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
Installation
Ensure that the junction box is clean and free of obstructions and that all
wiring is installed correctly. Review these instructions completely before
installing the controller.
Note: Follow applicable NEC and local electrical code
requirements when installing and powering the controller.
Install ELED1 with Nipple
Mount the controller directly to the exterior of the junction box or panel
either at the electrical load or before the load in the circuit.
1. Locate the circuit breaker panel and terminate power to the circuit.
2. Remove the cover plate and other hardware from the junction box to
access the wiring.
3. Mount the controller.
4. Refer to the Wiring Diagram on the next page to connect the
controller to line power, neutral, and load wires. Use wire nuts on all
connections and individually cap any bare wires, except the orange
antenna wire.
5. Connect the gray and the violet wires to the driver or ballast’s
dimming interface (optional).
6. Replace the electrical box cover plate and restore power to the circuit.
Install ELED1 with Mounting Strap
Mount the controller to the exterior of a lighting fixture or appliance
using the supplied mounting strap.
Note: Mounting inside a fixture or other metal cabinet will
reduce radio range performance.
1. Locate the circuit breaker panel and terminate power to the circuit.
2. Slide the mounting strap over the controller housing with the orange
antenna wire facing up. Hold the controller in place. The tooled strap
prevents the controller from sliding out.
3. Use a power drill to drive a 3/8 inch #8 screw through one of the
bracket’s mounting holes into the fixture. Repeat for the other
mounting hole.
4. Refer to the wiring diagram to connect the controller to line power,
neutral, and load wires. Use wire nuts on all connections and
individually cap any bare wires, except the orange antenna wire.
5. Ensure the antenna wire is not close to any metal surface (for
example: the lighting fixture metal housing).
LED Fixture Controller (120-277 VAC) Page 3 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
6. Connect the gray and the violet wires to the driver or ballast’s
dimming interface (optional).
7. Restore power to the circuit.
Note: The USB port is for factory use only. Do not attach cables
or accessories to this port.
Wiring Diagram
Max. Switching Load:
11.5A @ 120-277 V, 50/60 Hz
Electronic Ballast or LED Driver
LED Driver
ELED1
Antenna (orange)
Do not cut
or cap
Load (red),
Switched Line (Hot)
Dimming 0-10 V (violet)
Dimming COM (gray)
Neutral (white)
Max. Dimming Load: 100 mA sinking
Max. Impulse Voltage: 4000 V
Internal Relay: Type 1.C
Dimming output is Class 1 circuit
Independently mounted control for
panel mount/surface mount
Line Hot (black),
120-277 V
Diagram for Emergency Fixtures 1 of 2
ELED1
LED Driver
LED Driver Neutral
Normal Control Sense
Dimming +
Dimming +
Normal
Emergency
Load
UL924 Emergency
Bypass Relay
(Echoflex EREB-AD)
Normal Neutral
Emergency Line (Hot)
Emergency Neutral
Normal Line (Hot)
Dimming -
Dimming -
LED Driver Hot
ELED1
Load Control
Normal
Luminaires
LED Fixture Controller (120-277 VAC) Page 4 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
Diagram for Emergency Fixtures 2 of 2
Normal Line (Hot)
Normal Neutral
ELED1
Dimming + Dimming -LED +LED -
LED -
LED
Emitter
Board
LED
Driver
LED +
Battery
Backup
LED Driver HotLED Driver Hot
LED Driver NeutralLED Driver Neutral
ELED1 Load
Control
ELED1 Load
Control
Electrical Terminations
Power to the controller is connected between the white (neutral) and the
black line power (120–277VAC). The Class 1 power limited dimming
lines (violet and gray wires) can be used to provide 0–10V intensity
control of a dimming ballast or LED driver. The orange wire is an antenna:
Do not cut, cap, or connect this wire. Use only UL-approved wire when
making connections to the controller.
Connection Color Specification
Load Red 14AWG, 600V
Neutral White 14AWG, 600V
Line (hot) Black 14AWG, 600V
Dimming 0–10V Violet 18AWG, 600V
Dimming COM Gray 18AWG, 600V
User Interface
Note: Garibaldi Pro software is the ideal tool to set up your
project and configure settings, or even to make edits if your
project has been pre-commissioned. Garibaldi Pro is available for
download at echoflexsolutions.com.
Two buttons on the controller can be used to activate features and set
specific configurations directly on the device. Two LEDs beside the
buttons provide feedback about stored information and activities.
LED Fixture Controller (120-277 VAC) Page 5 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
Learn Button
The [Learn] button initiates Link mode for manually linking compatible
Echoflex devices to the controller. See the relevant switch or sensor
documentation for information on linking. Link mode times out after
60seconds of inactivity.
Devices can be linked to a controller manually, using Garibaldi Pro, or
during the Echoflex pre-commissioning process.
Remote Linking Solution
Use the following method to link the first switch if you cannot access the
[Learn] button on a controller that has not been pre-commissioned and
you do not have Garibaldi Pro software.
This method only works if there are no switches linked to the controller.
You cannot link a scene station using this method.
1. Ensure you are within wireless range of the controller and have a
wireless paddle switch.
a. If the controller has a linked sensor, you must press the [Teach]
button on the sensor and complete step 2 within 60 seconds.
2. Click the switch paddle ON three times, OFF three times, and ON
three times quickly, for a total of nine consecutive clicks. The relay
will toggle and the Power LED will indicate the switch is linked.
Clear Button
The [Clear] button can be used to reset the controller either to its pre-
commissioned state or to its factory default state.
To reset to pre-commissioned state:
1. Press and hold the [Clear] button until the red Power and green Learn
LEDs start blinking.
2. Release the [Clear] button. The Power LED blink codes indicate the
type and count of devices linked at pre-commissioning.
To reset to factory default state:
1. Press and hold the [Clear] button until the red Power and green Learn
LEDs start blinking, and continue to hold for 15 seconds until the
LEDs stay on solid.
2. Release the [Clear] button. The Power LED displays solid red to
indicates factory default state.
LED Fixture Controller (120-277 VAC) Page 6 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
Blink Indications
The tables below describe the LED codes that identify linked devices and
the LED indications that describe linking activities.
Device Count Codes
The following codes provide a visible report of the devices that are linked
to the controller. The Power LED repeats a code of blinks that represent
the type and number of linked devices. Long blinks = type. Short blinks =
count. If the controller does not have any linked devices, the Power LED
remains on solid.
Device Type Power LED LearnLED
Switches 1 long blink followed by short blinks
that count the switches Off
Occupancy sensors 2 long blinks followed by short blinks
that count the sensors Off
Photo sensor
(maximum of 1)
3 long blinks followed by short blink
that counts the sensor Off
Gateways and TimeClocks 4 long blinks followed by short blinks
that count the devices Off
Demand response 5 long blinks followed by short blinks
that count the devices Off
Entry door sensors 6 long blinks followed by short blinks
that count the sensors Off
Window sensors 7 long blinks followed by short blinks
that count the sensors Off
Keycard switches 8 long blinks followed by short blinks
that count the switches Off
Linking Activities
Activity Power LED LearnLED Light Response
Linkmode Blinking On solid Cycles ON and OFF
StorelinkID On for 4 seconds, and then
blinking On solid ON for 4 seconds, and then cycles
ClearlinkID Off for 4 seconds, and
then blinking On solid OFF for 4 seconds, and then cycles
LED Fixture Controller (120-277 VAC) Page 7 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
Test the Controller
Echoflex provides the controller in either a pre-commissioned state or a
factory default state.
•
Pre-commissioned devices are linked, configured, and labeled
according to customer specifications. When powered up, the red
Power LED repeats a blink code to indicate the type and number of
devices currently linked to the controller. To test, press the [Learn]
button or use a linked switch.
•
In factory default state, when powered up, the Power LED displays
solid red to indicate the controller has no linked devices. To test,
press the [Learn] button or link a switch. See relevant switch
documentation.
A maximum of 20 switches or sensors can be linked to one controller.
LED Fixture Controller (120-277 VAC) Page 8 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
Compliance
For complete regulatory compliance information, see the Echoflex LED
Fixture Controller (120-277 VAC) datasheet at echoflexsolutions.com.
FCC Compliance
Echoflex LED Fixture Controller (120-277 VAC)
(For any FCC matters):
Echoflex Solutions, Inc.
3031 Pleasant View Road
Middleton, WI 53562
[phone]
echoflexsolutions.com
This device complies with Part 15 of the FCCRules. Operation is subject to the following two
conditions:(1) this device may not cause harmful interference, and (2)this device must accept
any interference received; including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. Any modifications or changes to this product not expressly approved by
Electronic Theatre Controls, Inc. could void the user’s authority to operate the product.
Operation of this equipment in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at their own expense.
Contains FCC ID: SZV-STM300U
ISED Compliance
This device contains a license-exempt transmitter/receiver that complies with Innovation,
Science, and Economic Development Canada’s license-exempt RSSs. Operation is subject to
the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Contains IC ID: RSS 210
Conformité ISDE
Cet appareil contient un émetteur/récepteur conforme aux CNR d'Innovation, Sciences et
Développement économique Canada (ISDE) applicables aux appareils radio exempt de licence.
Son fonctionnement est soumis aux deux conditions suivantes:
1. L'appareil ne doit pas produire d'interférences.
2. L'utilisateur de l'appareil doit accepter toute interférence, même si l'interférence est
susceptible d'en compromettre le fonctionnement.
Contient ID IC: RSS 210
LED Fixture Controller (120-277 VAC) Page 9 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
LED Fixture Controller (120-277 VAC) Page 10 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
LED Fixture Controller (120-277 VAC) Page 11 of 12 Echoflex

Echoflex Installation Guide
LED Fixture Controller (120-277 VAC)
LED Fixture Controller (120-277 VAC) Page 12 of 12 Echoflex