ETC QuickTouch Preset User manual

ETC User Guide
QuickTouch Preset
Corporate Headquarters nMiddleton, WI, USA |[phone]
Global Offices nLondon, UK |Rome, IT |Holzkirchen, DE |Paris, FR |Hong Kong |Dubai, UAE |Singapore
New York, NY |Orlando, FL |Los Angeles, CA |Austin, TX
Web etcconnect.com |Support support.etcconnect.com |Contact etcconnect.com/contactETC
© 2022 Electronic Theatre Controls, Inc. |Trademark and patent info: etcconnect.com/ip
Product information and specifications subject to change. ETCintends this document to be provided in its entirety.
8063M1200-1.60 Rev A Released 2022-07
Overview
This user guide provides information on how to use the QuickTouch Preset controller. There are
multiple types of users that can log in to the QuickTouch Preset controller. Each user type has their
own purpose and the user interface responds based on who logs in. You can identify the type of
user for your login by the Group designation when you select your user during login.
Use the table below to identify your user type and the actions that you can perform from each
screen:
User Group Manual screen Presets screen Panel
Presets screen Settings screen
Emergency Manual move N/A N/A N/A
User
•
Manual move
•
Target move
•
Trim move
N/A N/A N/A
Preset Operator Go button to run Load preset N/A N/A
Operator
•
Manual move
•
Target move
•
Trim move
•
Load preset
•
Copy preset N/A N/A
Power User
•
Manual move
•
Target move
•
Trim move
•
Set trims
•
Set attached
load
•
Lock a motor
•
Advanced
config
•
Create preset
•
Load preset
•
Edit preset
•
Copy preset
•
Delete preset
•
Set as panel
preset
•
Configure OSC
N/A N/A
Panel Preset
Operator N/A N/A Run preset N/A
Panel User
•
Manual move
•
Target move
•
Trim move
N/A Run preset N/A
Admin N/A N/A N/A
•
Configure
display
•
Manage users

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 2 of 15 ETC
Warnings and Notifications
The operation of ETC Rigging equipment requires responsible use and specific training. Only
authorized, trained personnel should operate this rigging system. Unauthorized use, alteration, or
use for situations other than those for which it was designed may cause damage to the
equipment, other property damage, or injury to persons, potentially of a severe nature. All safety
precautions must be observed and adhered to at all times.
Read and obey the following warning statements to ensure safe and consistent use of your ETC
Rigging system.
WARNING: ETC Rigging systems must not be operated by a user until
installation and configuration have been completed by an ETC trained and
approved technician. Only ETC trained and approved technicians are authorized
to operate equipment during the installation and configuration process.
WARNING: Only properly trained and authorized persons shall operate ETC
Rigging systems.
WARNING: Improper operation may cause serious injury or death.
AVERTISSEMENT : Un fonctionnement incorrect peut provoquer des blessures
graves, voire mortelles.
WARNING: When using the ETC Rigging system, the user must have an
unobstructed view of the entire lineset and its attached load. If the user’s view
is obstructed, a second person (spotter) MUST be used to assist the operator at
all times. The spotter must have an unobstructed view of all moving components
and be able to maintain clear communication with the operator at all times.
If a problem arises while a hoist is moving (such as a mechanical issue or
interference from other objects) stop movement immediately by releasing all
Deadman and [Go] buttons or by using the Emergency Stop button. If a spotter
sees a problem while a hoist is moving, the spotter must signal the user to stop
movement immediately.
WARNING: Devices under control of the ETC Rigging system must only be used
to move a maximum load equal to or less than its rated capacity. Overloading
the device may result in damage to the system, other property damage, serious
injury, or death.
AVERTISSEMENT : Les appareils sous le contrôle du système ETC doivent
uniquement être utilisés pour déplacer une charge maximale équivalente ou
inférieure à sa capacité nominale. Une surcharge de l'appareil peut entraîner
l'endommagement du système et d'autres biens, des blessures graves, voire la
mort.

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 3 of 15 ETC
WARNING: Disconnect power before servicing this equipment.
AVERTISSEMENT : Déconnectez l'alimentation avant d'effectuer l'entretien
de cet équipement.
WARNING: The Working Load Limit (WLL) of any device is the maximum load
capacity that a user may apply to that device or system.
All ETC Rigging hoists have a Working Load Limit. This is identified on the
product label on the back of the hoist and on the batten label. This limit is not
the same for all hoists; be sure to check the Working Load Limit for all hoists in
your system. Prodigy Working Load Limits include a design-safety factor.
If you cannot find a Working Load Limit for any device under the control of the
ETC Rigging system, do not operate and contact your ETC Rigging installer.
NEVER exceed the Working Load Limit for any hoist.
WARNING: Do not exceed point load, Uniform Distributed Load (UDL), or
Working Load Limit (WLL) for any line set. See label on batten for POINT, UDL,
and WLL. Point, distributed, and working load limits may be different for each
device.
Do not suspend persons from the device or any of its components. Do not ride
on the batten.
Stop use of the system immediately if unusual noises are heard or unusual
smells are detected during operation. Contact a qualified ETC Rigging inspector
before resuming use.
In the event of an Emergency Stop (E-stop) cease use of the system, identify
who engaged the E-stop and why, and resolve the issue before restarting the
system.
Never lock or jam the operating buttons in the depressed (“on”) position. These
hold-down buttons must be operated by a competent person at all times. Log
out or remove the enable key of this rigging controller when a competent or
qualified person is not present.
Use a remote unit when the load is obscured from this operator position or have
someone observe the load while it is moving. Never leave the controller when a
hoist is in motion.
Prior to servicing the system, disconnect and lock out/tag out power (according
to NFPA Standard 70E) to any relevant components.
Always inspect and test the ETC Rigging system before each use.
Have certified ETC Rigging inspector perform regular inspection and
maintenance as dictated by the system installer, ETC's specifications, and
warranty agreements. The system must be inspected annually by a qualified ETC
Rigging inspector.

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 4 of 15 ETC
Login
To log in to your controller, press Login from the main screen. When the User Login dialog
appears, select the appropriate user login from the list. This causes the Enter Pin Code dialog to
appear. Enter your user code and press Ok to log in.

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 5 of 15 ETC
Manual
The Manual screen contains rows of channels on the top of the screen and configuration and
movement options on the bottom of the screen.
Move Motors Manually
1. Select one or more channels to move.
2. Adjust the speed slider to the speed you want. The slider is directly to the left of the blue and
green Up and Down buttons. If you move the slider all the way up the motor will move at its
maximum speed.
3. Select the blue Up button or green Down button depending on which way you want to move
the hoist.
4. Press and hold the [GO] button to move the hoist in the direction and at the speed that you've
selected.
5. Release the [GO] button when the hoist reaches the intended destination.
Perform Target Moves
1. Select one or more channels to move to a specific target and then press the editable Target
field in the properties area.
2. In the Edit Target Position dialog that appears, enter the target destination and press Ok.
3. Press and hold the [GO] button to move to the target destination.
Move Channels Using Trims
1. Select the channel you want to move.
2. Press one of the trim buttons from the properties area to select the trim as your destination.
Note that the trim value is now displayed in the Target field.
3. Press and hold the [GO] button to move to the trim.
Set Trims
Set trims for the channels from the trim fields (Low Trim, Trim 1, Trim 2, High Trim) or from the
Trims tab in the Advanced dialog. When you select a trim from either workspace, the Edit trim
dialog appears and lets you set or edit a trim, including renaming the trim. You can also designate
the Low and High trims as limits if you want.

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 6 of 15 ETC
Set Attached Load Position
Set the attached load position so the position readout indicates the bottom of the attached load
(i.e. bottom of the scenery) as opposed to the actual batten position. This allows you to move a
motor to 0'0" so that the scenery touches the stage and the batten remains at the specified
elevation above the stage.
1. Manually move the motor so that the attached load (i.e. scenery) rests at the lowest desired
position.
2. With the channel still selected, press the Load Attached button to open the Scenery Bottom
Position dialog.
3. Enter the position of the bottom of the load:
•
If the load is physically touching the stage, enter 0'0"
•
If the load is floating, enter the measured distance between the stage and the bottom of the
load
4. Press Ok.
Any channel that has a load attached configured displays a horizontal bar below the channel
position. For example, the following image shows the attached load position is set to 40' 0" for
channel 1.
Lock Motors
The Lock button is available only to Power Users and can be found in the lower left part of a
channel's properties area. Press Lock to lock the selected channel and prevent it from moving in
any way. Press Lock again to unlock the channel.

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 7 of 15 ETC
Advanced Configuration
Open the Advanced dialog for any channel to access the following tabs and their respective
functions.
•
Trims: Allows you to set trims for the motor
•
Load: Provides load information for the motor
•
Speed: Provides speed information for the motor
•
Status: Provides system status and history
•
Statistic: Provides statistical information
•
Diagnostic: Provides diagnostic information
Load Profiling
It is highly recommended that you enable load profiling for your motors. This feature allows you to
record a normal profile of what the load should be at any point in the full range of travel, in both
directions. Load profiling then monitors the load during movement and stops movement when
unexpected load conditions occur.
To record these load profiles and subsequently enable load profiling:
1. Select the Load tab and press the Learn button.
•
For standard loads (i.e. scenery or non-electric loads), press the Save button.
•
For loads that change during travel, press the Record button.
-
Record the up and down profiles for the load
-
Save the profiles when you are satisfied
-
Close the Learn Load dialog
2. From the Load tab, you can now select the Enable Profiling button (outlined in gold when
selected).
3. You can also change the sensitivity setting per motor, with Maximum having the lowest
tolerance for deviance from the load profile and Low having the greatest tolerance.
Speed Configuration
Select the Speed tab and press the Max Speed field. In the dialog that appears, enter the
maximum speed at which you would like the motor to run. Press the Min Ramp Time field and in
the dialog that appears, enter the minimum ramp time.

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 8 of 15 ETC
Presets
The Presets screen contains the same rows of channels on the top of the screen and configuration
options for presets on the bottom of the screen. Note that there may be some system presets that
are locked for editing. These can only be created or modified by a system installer.
Create Presets
1. From the Presets screen, press New to open the New Preset dialog.
2. Press the Number field and use the Edit Preset Number dialog if you want to change the preset
number.
3. Press the Name field and use the Preset Name dialog that appears to change the preset name.
4. Press Create.

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 9 of 15 ETC
Add Preset Content
Note: It is recommended that you use trims when building groups, presets, and cues.
Because trims represent a universal way to update a motor position, this allows updates
throughout all references to be simultaneous. If a desired position changes (for example,
due to soft goods stretching), trim-based references can be updated by altering a single
referenced trim position.
1. From the Presets screen, select the preset to which you want to add content.
2. Select a channel that you want to be in the preset. A position dialog box appears.
3. Enter the desired preset position for the motor for this preset.
•
Reference a trim position by selecting from the four available trims or pressing Trims to see
other recorded trims.
•
Press Current to store the current position of the channel.
•
Enter a specified position by selecting the position field.
4. Press Ok to close the motor position dialog.
5. Repeat these steps for any other channels you want to be included in the preset.
Note: Preset content is stored automatically. You do not need to save a preset once it
has been created, nor after content has been updated.
Play a Preset
To play a preset, simply select the preset from the list and press the Load button. This takes you
directly to the Manual tab where you can press the [GO] button to run the preset.
Edit Presets
To edit a preset, select the preset you want to edit and perform the following actions:
•
Add a channel: Select the channel to add and set the desired preset motor position.
•
Remove a channel: Select the channel to open the position dialog and then press Remove.
•
Edit motor position: Select the channel to open the position dialog and then change the
desired motor position.

ETC User Guide
QuickTouch Preset
QuickTouch Preset Page 10 of 15 ETC
Copy Presets
You can copy any existing preset into a new or existing preset.
Copy to a New Preset
1. Select the desired preset from the Presets screen.
2. Press Copy to open the Copy Preset dialog.
3. Press the Number field and use the Edit Preset Number dialog if you want to change the preset
number.
4. Press the Name field and use the Preset Name dialog that appears to change the preset name.
5. Press Create.
Note: When you copy a panel preset, the newly created preset is also designated as a
panel preset. Conversely, when you copy a system preset, the new preset is not
designated as a system preset.
Copy to an Existing Preset
CAUTION: Copying a preset into an existing preset will overwrite any content
in the existing preset entirely. A confirmation dialog will open if you attempt to
overwrite an existing preset.
Overwriting an existing preset that is referenced in the cue stack may severely
modify the look of your show. If you do so, it is important to double check and
most likely re-program the cue stack.
You are about to delete preset content that cannot be recovered.
1. Select the desired preset from the Presets screen.
2. Press Copy to open the Copy Preset dialog.
3. Press the Number field and use the Edit Preset Number dialog if you want to change the preset
number.
4. Press the Name field and use the Preset Name dialog that appears to change the preset name.
5. Press Create. From the Copy Preset # dialog that appears, select Yes or No.
•
Yes overwrites the preset with the copied content.
•
No returns you to the Copy Preset dialog.