ETC ArcSystem Navis 100 User manual

ArcSystem
Navis 100 Sidekick
Installation Guide
Part Number: 7496M2150 Rev C
Released: 2023-02

To view a list of ETCtrademarks and patents, go to
etcconnect.com/ip. All other trademarks, both marked and not
marked, are the property of their respective owners.
ETC intends this document, whether printed or electronic, to be
provided in its entirety.

Table of Contents
Sidekick Installation Guide i
Overview 1
Help from ETC Technical Services 2
Safety 3
Features 4
Installation Accessories 5
Before You Begin Installation 6
Power Disconnect Device 6
Installation Requirements 6
Electrical and Wiring Specifications 7
Recommended ETC Dimmer Settings 8
Installation 8
Prepare the Ceiling 8
Spacing for Wall Wash Luminaires 8
Assemble Navis 100 Sidekick/Luminaire 9
Install the Luminaire 10
Install a Wall Wash Luminaire 12

Power Up Procedure 14
Maintenance 14
Specifications 15
Compliance 15
FCC Compliance 15
ii Sidekick Installation Guide

Sidekick Installation Guide 1
Overview
This guide provides installation instructions for the ArcSystem Navis 100
Sidekick LED driver. The Navis 100 Sidekick LEDdriver is a stand-alone
power supply that attaches directly to a Navis 100 luminaire. The driver
allows you to install a Navis 100 luminaire in a location where connection to
a central LED driver is not convenient.
The Navis 100 Sidekick LED driver is intended for use only with Navis 100
White and Fade to Warm luminaires. The driver is available in a 600mA
constant current (CC) model for use with Navis 100 White luminaires and a
450mA CC model for use with Navis 100 Fade to Warm luminaires. North
American and European variants are available for each model.
Model Number Compatible Navis 100
Luminaire*
Constant Current
(mA) Region
ARCN-SK100-WC White 600 North America
ARCN-SK100-FTWC Fade to Warm 450
ARCN-SK100-WC-CE White 600 Europe
ARCN-SK100-FTWC-CE Fade to Warm 450
*The Navis 100 luminaire is shipped separately from the Navis 100 Sidekick LED driver.
CAUTION: The Navis 100 Sidekick LEDdriver is not
compatible with the Navis 100 Pendant or Surface Cylinder
accessories.
Review the ArcSystem Navis 100 Installation Guide prior to installing the
Navis 100 Sidekick LED driver to familiarize yourself with the luminaire. The
installation guide is provided with the Navis 100 luminaire and is also
available for download free of charge from the ETC website:
etcconnect.com/ArcSystem-Navis/Documentation.

2 Sidekick Installation Guide
Help from ETC Technical Services
If you have questions that are not answered by this document, try the ETC
support website at support.etcconnect.com or the main ETC website at
etcconnect.com. If none of these resources are sufficient, contact ETC
Technical Services directly at one of the offices identified below. Emergency
service is available from all ETC offices outside of normal business hours.
When calling for help, take these steps first:
• Prepare a detailed description of the problem
• Go near the equipment for troubleshooting
• Find your notification number if you have called in previously
ETC, Inc.
Americas
Technical Services Department
3031 Pleasant View Road
Middleton, WI 53562
800-775-4382 (USA, toll-free)
[phone]
[e-mail]
ETC GmbH
Germany, Austria, Switzerland,
Eastern Europe, and Russia
Technical Services Department
Ohmstrasse 3
83607 Holzkirchen, Germany
[phone]
[e-mail]
ETC Austin
High End Systems Products
Technical Services Department
2105 Gracy Farms Lane
Austin, TX 78758 USA
800-890-8989 (USA, toll-free)
[phone]
[e-mail]
ETC France
France
Zone Urbaparc -
Bâtiment E
6 Boulevard de la Libération
Saint-Denis, 93200
[phone]
[e-mail]
ETC Ltd
Europe, Middle East, and Africa
Technical Services Department
26-28 Victoria Industrial Estate
Victoria Road,
London W3 6UU England
[phone]
[e-mail]
ETCAsia
Asia
Technical Services Department
Room 1801, 18/F
Tower 1, Phase 1 Enterprise Square
9 Sheung Yuet Road
Kowloon Bay, Kowloon, Hong Kong
[phone]
[e-mail]

Sidekick Installation Guide 3
Safety
Read the entire guide before using this equipment.
The Navis 100 Sidekick LED driver is not user-serviceable and should only be
serviced by a qualified technician. Contact ETC Technical Services for
assistance.
Symbols used on the product label are defined below:
General warning Avertissement général
This product should not be
discarded as unsorted waste but
must be sent to separate
collection facilities for recovery
and recycling.
Ce produit ne doit pas être jeté
avec les déchets ménagers mais
doit être déposé dans une collecte
de déchets électroniques ou dans
un point de collecte.
This product meets the safety
requirements specified for Class II
equipment according to IEC
61140 or IEC60536.
Ce produit à Protection Classe II
Double isolation est conforme aux
normes IEC 61140 ou IEC 60536.
The product input or output is
suitable for direct current only.
L’entrée et la sortie de ce produit
convient uniquement au courant
continu.
The product input or output is
suitable for alternating current
only.
L’entrée et la sortie de ce produit
convient uniquement au courant
alternatif.
Safety extra low voltage device Dispositif de sécurité à très basse
tension
Independent lighting control gear Appareil de contrôle d’éclairage
indépendant.
The driver is thermally protected
to the value located in the
triangle in degrees Celsius.
Le pilote est protégé
thermiquement à la valeur située
dans le triangle en degrés Celsius.

4 Sidekick Installation Guide
Features
1
2
Navis 100 Sidekick LED Driver
1 Installation screw (T20 Torx, captive)
2 RJ45 plug
3
4
1
3
2
Navis 100 Luminaire
1 In port (RJ45 socket)
2
Threaded screw hole for the
installation screw in the Sidekick
LED driver
3 Mounting clamps (quantity 3)
4 Magnetic trim plate
A
A
A
B
C
C
C
Navis 100 Luminaire with Trim Plate Removed
A
2 mm hex screws or T10 Torx
screws (silver) for mounting
clamps
B
2 mm hex screw or T10 Torx
screw (yellow) to lock the tilt
and rotation
C Magnets that secure the trim plate

Sidekick Installation Guide 5
Installation Accessories
Several installation accessories are available for purchase separate from the
luminaire. Contact ETC or your authorized ETC dealer to purchase these
accessories.
•ArcSystem Recessed Luminaire Ceiling Bracket: The
ArcSystem Recessed Luminaire Ceiling Bracket is
intended for use in new installations or when
additional support is required for hanging a
luminaire. The recessed ceiling bracket can be
secured to the rail system in suspended ceilings or
attached directly to building joists. The bracket and related hardware
are designed to attach to 25mm EMT conduit and 3/4in EMT
conduit, which is cut to size on-site and supplied by others. For more
information, download the ArcSystem Recessed Luminaire Ceiling
Bracket Installation Guide from etcconnect.com or scan the QR code.
•ArcSystem Goof Ring: The ArcSystem Goof Ring is a
trim ring that conceals gaps caused by ceiling holes
that are too large for the luminaire you are
installing. For more information, download the
ArcSystem Goof Ring Installation Guide from
etcconnect.com or scan the QR code.
•ArcSystem C-ring: The ArcSystem
C-ring provides a rigid surface for the
luminaire mounting clamps when the
ceiling material is too soft to support
fully tightened mounting clamps.
Information about using the C-ring is
included in the luminaire's installation
procedure.

6 Sidekick Installation Guide
Before You Begin Installation
Review the following sections before you begin installing the luminaire and
driver.
Power Disconnect Device
Before installation, make sure that you have a readily accessible input
power disconnect device installed ahead of your Navis 100 luminaire and
the driver.
WARNING: RISK OF ELECTRIC SHOCK! Circuits that are
installed without an accessible power disconnect device
cannot be serviced or operated safely.
AVERTISSEMENT : RISQUE DE DÉCHARGE ÉLECTRIQUE! Il est
imprudent d'utiliser ou de réparer les circuits installés sans
qu'un dispositif de déconnexion de l'alimentation ne soit
accessible.
Installation Requirements
WARNING: Navis 100 luminaires are NON-IC rated and
therefore NOT suitable for installation in direct contact with
combustible materials or thermal insulation.
DO NOT INSTALL INSULATION WITHIN 76mm (3in) OF ANY
PART OF THE LUMINAIRE.
AVERTISSEMENT : Les lampes Navis 100 sont classés
NON-IC, ils ne conviennent donc PAS pour une installation en
contact direct avec des matières combustibles ou une
isolation thermique.
NE PAS INSTALLER D’ISOLATION À MOINS DE 76mm (3po) DE
TOUTE PARTIE DE LA LAMPE.
WARNING: The luminaire must be installed at least 0.1 m
(4.0 in) away from all lighted objects.
AVERTISSEMENT : Le luminaire doit être installé à au moins
0,1 m (4,0 po) de tout objet allumé.