Ethnicraft Spindle Bed User manual

TEAK SPINDLE BED - QUEEN SIZE - WITH SLATS
ASSEMBLY INSTRUCTIONS FOR BED INSTALLATION
1 / 5
DIRECTION NUMBER OF
PERSONS NEEDED
USE SCREWDRIVER
TO TIGHTEN
USE L KEY
TO TIGHTEN
USE HANDUSE WRENCH
TO TIGHTEN
USE HALFMOON KEY
TO TIGHTEN
X3
NOTICE
IN YOUR PACKAGE :
ASSEMBLY INSTRUCTIONS
HARDWARE (AS LISTED ABOVE)
PARTS TO BE INSTALLED :
1. HEADBOARD 1pc
2. BED HEAD 1pc
3. FOOTBOARD 1pc
4. SIDERAILS 2pcs
5. CENTER SUPPORT 1pc
6. CENTER LEG 1pc
7. SLATS SUPPORTS 2pcs
8. SLATS 1set
SCREWDRIVER
TOOLS
L KEY
( Included in package )
HARDWARE ENCLOSED
BOLT KEY
( Included in package )
HALF MOON
WASHER
(4pcs)
BOLT
M8x100 mm
(4pcs)
DOWEL
Ø12x50 mm
(8pcs)
JCBC SCREW
M6x70 mm
(3pcs)
WRENCH
L BRACKET
(8pcs)
LONG NUT
M6
(2pcs)
(Included in package)
JCBC SCREW
M6x6mm
(8pcs)
(Not included in package)
JF SCREW
M6x50mm
(5pcs)
SPRING WASHER
M6
(2pcs)
WASHER
M6
(22pcs)
NUT
M6
(22pcs)
JF SCREW
M6x80
(18pcs)
WASHER
M6x18
(2pcs)
SYMBOLS
1
(L)
(R)
2
3
4
5
6
4
8
7
7

2 / 5
6
5
CONNECTING SIDERAIL AND HEAD / FOOTBOARD
A.
B.
CONNECTING CENTER LEG TO CENTER SUPPORT
- USE DOWEL Ø12x50 (8X)
- USE HALFMOON BOLT M8x100 (4X)
- USE HALFMOON WASHER (4X)
- TIGHTEN FULLY
4
1 2
3
5
1
4
1
1 2
3
- USE JF SCREW M6x50 (1X)
- TIGHTEN FULLY
1
4(L)
4 (R)
3
ATTACH SIDERAIL
WITH DRILL HOLE
TO HEADBOARD
TEAK SPINDLE BED - QUEEN SIZE - WITH SLATS
ASSEMBLY INSTRUCTIONS FOR BED INSTALLATION

3 / 5
1 2
4
3
3
1 2
TO ADJUST HEIGHT
4
INSTALLING CENTER SUPPORT
C.
- USE L BRACKET (2X)
- USE JCBC SCREW M6x6 (2X)
- USE JF SCREW M6x50 (4X)
- USE WASHER M6 (4X)
- USE NUT M6 (4X)
- TIGHTEN FULLY ALL SCREWS
D.
INSTALLING SLAT SUPPORTS
- USE L BRACKET (6X)
- USE JCBC SCREW M6x6 (6X)
- USE JF SCREW M6x80 (12X)
- USE WASHER M6 (12X)
- USE NUT M6 (12X)
- TIGHTEN FULLY ALL SCREWS
- INSTALLING SLAT SUPPORTS AT THE SAME
LEVEL WITH CENTER SUPPORT
7
7
TEAK SPINDLE BED - QUEEN SIZE - WITH SLATS
ASSEMBLY INSTRUCTIONS FOR BED INSTALLATION

4 / 5
1
INSTALL SCREW ON THE MIDDLE SIDE FIRST
THEN INSTALL SCREW ON THE OTHER SIDE
- USE JCBC SCREW M6x70 (1X)
- DO NOT FULLY TIGHTEN
- USE JCBC SCREW M6x70 (2X)
- USE WASHER M6x18 (2X)
- USE SPRING WASHER M6 (2X)
- USE LONG NUT M6 (2X)
- DO NOT FULLY TIGHTEN
1
2
INSTALLING BED HEAD
E.
2
2
TEAK SPINDLE BED - QUEEN SIZE - WITH SLATS
ASSEMBLY INSTRUCTIONS FOR BED INSTALLATION

5 / 5
2
1
RE-TIGHTEN THE SCREWS
F.
G.
INSTALLING SLATS
TIGHTEN FULLY ALL SCREWS
- USE JF SCREW M6x80 (6X)
- USE WASHER M6 (6X)
- USE NUT M6 (6X)
- SLATS TO BE ASSEMBLED ARE NUMBER 1, 6, AND 13
- TIGHTEN FULLY ALL SCREWS
8
TEAK SPINDLE BED - QUEEN SIZE - WITH SLATS
ASSEMBLY INSTRUCTIONS FOR BED INSTALLATION