eTIGER S4 Combo Secual User manual

www.etiger.com
Quick Start Guide
S4 Combo Secual / S4 Combo Vid Secual

EN

4
How do you wish to interact with your control panel?
- Using a landline connection enables a basic interaction with
your alarm system (by phone call).
- Using a SIM card (sold separately) enables a more advance
interaction with your system (by phone call, SMS or app).
- Using both the SIM card and the landline connection oers
an optimal security, as you always have a backup in case your
landline or your cellular network is down.
If you do not wish to use a SIM card, go directly to step 4.
1
Landline or SIM card?
This step only applies
if you are using your system with a SIM card.

5
EN
Disable the security of your control panel’s SIM card
The S4 control panel can interact with you thanks to a SIM
card (sold separately). Before inserting your SIM card in the
control panel, make sure the SIM security is o. To do so,
insert the SIM card in a mobile phone, browse the settings of
the phone and disable the SIM security (if the SIM security is
activated, the PIN code will be required).
A piece of advice
For your control panel’s SIM card, we advise you to choose a
plan with unlimited text and 1 or 2 hours of call.
2
Settings
SIM PIN
Request a PIN code to
unlock the phone.
O
This step only applies
if you are using your system with a SIM card.
Control panel’s
SIM card

6
SIM
3
Insert the SIM card in the control panel
Open the battery compartment at the back of your control
panel and insert the SIM card in the SIM card slot.
Important
- Insert the SIM card according to the shape of the SIM card
slot.
- The SIM card must be compatible with the GSM network.
Contact your carrier for more information.
If you do not wish to connect your system to a landline, go
directly to step 5.
This step only applies
if you are using your system with a SIM card.
This step only applies
if you wish to connect your system to a landline.

7
EN
Connect the control panel to your landline
1. Connect the smaller connector of the telephone cable
(supplied in your kit) to the landline interface in the battery
compartment at the back of the control panel.
2. Connect the other end of the telephone cable to the your
landline socket or to the phone connector of your ADSL box.
4
This step only applies
if you are using your system with a SIM card.
This step only applies
if you wish to connect your system to a landline.

8
Turn the control panel on
Plug the AC adaptor to an AC socket. Plug the output
connector of the AC adaptor into the adaptor interface in
the battery compartment at the back of the control panel.
Turn the power switch to“ON”and put back the cover of the
battery compartment. The control panel is turning on.
Important
Before turning your control panel on, make sure you have
either inserted a SIM card or connected it to your landline.
5

9
EN
6
Mount the control panel on a wall
Screw the wall mount onto the wall where you wish to install
your control panel. Fix the control panel on the wall mount.
Some advice
- Make sure the control panel is rmly xed on the wall mount.
Because of the tamper switch, the alarm rings out if the
control panel is separated from the wall mount.
- If you are using a SIM card, make sure the GSM reception of
the control panel is sucient before screwing the wall mount
onto the wall.
UP

10
7
Change the system language
The language of your system can be changed from the menu of
the control panel:
1. Type your Admin Code + on the control panel.
(Default Admin Code: 123456)
2. Go to System Settings > Language.
3. Select the language and conrm with .
A piece of advice
Type your Admin Code + to enter the menu and navigate
with , , ,(back), or (delete).
System Settings
Language

11
EN
System Settings
Language
8
Activate or deactivate the GSM / Landline mode
Ignore this step if you are using the control panel with a SIM card
AND a landline connection.
Using a landline connection only
1. Type your Admin Code + on the control panel.
2. Go to System Settings > GSM Fail Tip. Select OFF and press .
Using a SIM card only
1. Type your Admin Code + on the control panel.
2. Go to System Settings > Linecut Alarm. Select OFF and press .
System Settings
GSM Fail Tip

12
Register a phone number
This step enables you to dene the phone number(s) on which
you receive a phone call when the alarm is triggered.
1. Type your Admin Code + on the control panel.
2. Go to Phone number > Phone 1 is and press .
3. Enter your phone number and conrm with .
If you register a phone number and an SMS number, you will be
notied by SMS and by phone call in case of alarm.
If you do not wish to use a SIM card, skip step 10.
9
Phone 1 is:
057890033
This step only applies
if you are using your system with a SIM card.

13
EN
Phone 1 is:
057890033
Register a SMS number
This step enables you to dene the phone number(s) to which an
SMS is sent when the alarm is triggered. Only stored numbers can
control and congure the system by SMS and App.
1. Type your Admin Code + on the control panel.
2. Go to Phone number > SMS Num 1 is and press .
3. Enter your phone number and conrm with .
10
SMS Num 1 is:
067890033
This step only applies
if you are using your system with a SIM card.

14
Your system is ready.
Now what happens if the alarm is triggered?
1. The siren of the control panel rings out.
2. You receive a phone call. Pick up the call: you hear a voice
prompt giving you a list of options (stop the siren, disarm the
system, start audio surveillance etc.)
3. If there is a SIM card in your control panel, you also receive an
SMS notifying you that the alarm has been triggered.
Advanced setup
The control panel of your alarm system features an LCD display
that enables you to navigate through the menu of the control
panel and set up your alarm system.
For more settings, please refer to the user manual of the
control panel, available for download on
www.etiger.com.
Advanced settings
For the installation of your accessories, please check the full
manual of www.etiger.com.
Connect more sensors
1.Type your Admin Code + on the control panel.
2.Go to Accessories > Wireless Sensors and press .
3.Select the type of zone and press .
4.Within the next 15 seconds, trigger the sensor.
5.You hear one beep: the accessory is registered.
Change the Access Codes
The User Code enables you to disarm your system from the
panel.
1.Type your Admin Code + on the control panel.
2.Go to System Settings > Access Code > User Code > .
3.Change the code and press (the code must consist of 4
digits).
The Admin Code can be changed using the same procedure
(under System Settings > Access Code > Admin Code).

15
EN
Advanced settings
For the installation of your accessories, please check the full
manual of www.etiger.com.
Connect more sensors
1.Type your Admin Code + on the control panel.
2.Go to Accessories > Wireless Sensors and press .
3.Select the type of zone and press .
4.Within the next 15 seconds, trigger the sensor.
5.You hear one beep: the accessory is registered.
Change the Access Codes
The User Code enables you to disarm your system from the
panel.
1.Type your Admin Code + on the control panel.
2.Go to System Settings > Access Code > User Code > .
3.Change the code and press (the code must consist of 4
digits).
The Admin Code can be changed using the same procedure
(under System Settings > Access Code > Admin Code).

16
Precautions
For a safer use of the product and to optimize the lifespan of the
product, we recommend you to follow the precautions below:
- The wireless accessories must be connected to the control panel.
- Low power voltage may aect transmission distance.
- Do not press the SOS key on the remote control if it is unnecessary
to avoid disturbing neighborhood.
- Check the system regularly to make sure the system works
properly.
- The control panel is neither waterproof nor moisture-proof, install
it in a shady, cool and dry place.
- The case of the control panel is made of ABS plastic. Keep away
from bright light for a longer lifespan.
- The control panel is not explosion-proof. Keep away from re and
ames.
- Install the control panel away from objects such as heater,
air conditioner, microwave oven etc. that generate heat or
electromagnetic elds.
- Dispose of the batteries according to local regulations.
- Dismantling of this product must be done by professional
personnel only.

17
EN
ATTENTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sucient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
To prevent re or shock hazards, do not expose this product to rain
or moisture. Apparatus shall not be exposed to dripping or splashing
and no object lled with liquids, such as vases, shall be placed on the
apparatus.

18
Standards
This product bears the selective sorting symbol for waste electrical
and electronic equipment (WEEE). This means that this product must
be handled pursuant to European Directive 2012/19/EU in order to be
recycled or dismantled to minimize its impact on the environment.
For further information, please contact your local or regional authorities.
Electronic products not included in the selective sorting process are
potentially dangerous for the environment and human health due to the
presence of hazardous substances.
In compliance with European laws. This product is in compliance with
the essential requirements and other relevant provisions of Directive
2014/53/EU.
This product was designed and manufactured in compliance with
Directive 2011/65/EU of the European Parliament and of the Council on
the restriction of use of certain hazardous substances in electrical and
electronic equipment (RoHS Directive - RoHS) and is deemed to comply
with the maximum concentration values set by the European Technical
Adaptation Committee (TAC).
Manufactured in China.
Images, illustrations and text are non-contractual. eTIGER and the eTIGER
logo are registered trademarks and the property of eTIGER.
Copyright © 2019 eTIGER. All rights reserved.

FR

20
Comment souhaitez-vous interagir avec la centrale ?
- Connexion ligne xe : permet une interaction basique avec
votre système (par appel téléphonique)
- Avec carte SIM (vendue séparément) : interaction complète
avec le système (par appel, SMS ou application)
- Connexion ligne xe ET carte SIM : sécurité optimale, vous
êtes toujours en contact avec votre alarme, même en cas de
coupure de ligne xe ou de panne réseau.
Si vous ne souhaitez pas utiliser de carte SIM, rendez-vous
directement à l’étape 4.
1
Ligne xe ou carte SIM ?
Cette étape s’applique uniquement
si vous utilisez une carte SIM.