eTIGER S2 User manual

S2
S2 U20130719V1
TL SECUAL
Security Alarm System
EN Thanks for purchasingTL SECUAL alarm.
FR Merci d’avoir achet l’alarme TL SECUAL.
ETIGER EUROPE – Rue de la Loi 25 - 7100 La Louvière – Belgium
[e-mail] - www.etiger.com
Copyright © ETIGER EUROPE 2013

Table of Contents
Included Accessories
Control Panel Layout
Preparation before Use
3~4
4~5
6
Power on
Connect PSTN Land Line
Installation
Alarm Control
Access Control System
Dialing Calls
Voice Memo
Function Setting
Alarm Phone Number Setup
Add/Delete /Edit Accessories
System Settings
Date and Time
Entry/Exit Delay
Backlight Time
Timed Arm / Disarm
Edit Greeting Message
Remote Phone Control
Linecut Alarm
Control Panel Operation 7~8
LCD Display Contents
LCD Display Menu
Settings
9
10~11
12~22
Add CMS Phone Number
Delete CMS Phone Number
User ID
Upload Arm/Disarm Report
Contact ID Reports
Precautions
FA
Wireless Remote Control
Wireless Door/Window Contact
Wireless PIR Motion Detector
24
25
25
26
27~28
28~30
Specications
Access Code
Ringing Times for Phone Remote Control
Alarm Voice
Siren Setup
User ID for CMS
Upload Arm Report
Upload Disarm Report
Reset
Keypad Tones
Check Event Logs
Connect to Electronic Lock 23
Connect to CMS Center 23~24
2
1
PSTN/LCD/RFID
Touch Alarm System
Features
100% wireless conguration, installationD.I.Y.
Fashion design with digital touch keypad
LCD display with guide menu, easy for programming
ARM + Auror high quality CPU
Built-in 1, 000, 000 RF codes combination maintains high reliability
Support 10 remote controls, 50 wireless sensors and 50 RFID tags
Store 6 alarm phone numbers and 2 CID CMS numbers
10 seconds voice memo and recordable alarm voice message
Disarm the system by RFID tags and unlock the electronic door
Support low power feedback and tamper alarm for wireless sensors
Support maximum 150 alarm event logs
Control panel can dial calls directly
Remote arm, disarm and monitor by phone operation
Duress code enables sending out alarm notication mutely
One group of timing arm and disarm
Support exit/entry delay
Rename all zones and RIFD tags
Voice prompt during phone remote control
EN Please read this user manual carefully
before using,Please kindly keep this
user manual for your reference
when necessary.

Brackets (wall-mounted and
desktop) for control panel x 2
Bracket for PIR Motion
Detector x 2
Double-sided tape for
Door/Window Contact x 2
Screws x 6
User Manual x 1
RFID Tag Reader /
Play Voice Memo
Home Mode (Part Arm)
Disarm
Arm
Voice Memo Button
Status Indicator
LCD Display
Esc
Up/Down
Enter
SOS
Clear
Call
Front Side
Control Panel Layout
4
3
Included Accessories
The control panel is known as the “heart and brain” for
alarm system, which is used for receiving and processing
signals from wireless sensors and remote controls. Users
can make settings freely with the keypad and LCD display.
In case of emergency, the panel hoots on site and dials
the pre-stored alarm phone numbers automatically.
When users pick up the phone, they are able to hear
alarm voice message and choose to monitor on site or
disarm the system.
The wireless PIR Motion Detector is an
intelligent passive infrared motion sensor,
designed to detect human movements
within an approximate range of 6 to 8
meters from the detector. The detector
includes fuzzy logic to minimize false alarms
from unwanted heat sources. With power
saving feature, the detector will enter
sleeping mode after the second activation
within 3 minutes to save power.
S2 Control Panel x1
Wireless PIR Motion Detector x 2
The Door/window contact can be installed
on doors, windows and any other objects
that open and close. The sensor transmits
signals to the control panel when a magnet
mounted near the sensor is moved away.
The RFID tag is for disarming,The system
and unlocking the electronic door lock (if
connected).
Supply power to the control panel. In case of power
failure, two built-in backup batteries in the panel will
support 5-hour standby.
The remote control is compact and
portable; it is convenient to carry it to arm,
disarm, part arm the alarm system and also
make an emergency call.
Wireless Remote Control x 2
Wireless Door/Window Contact x 2
Telephone Cable x 1 AC Adapter x 1
RFID Tag x 2
Connect PSTN land line to the control
panel.In case of emergency, the panel
will hoot on site and call the pre-stored
alarm phone number to notify users.

6
5
Preparation before Use
Turn the power switch from OFF to ON.
1. Power on
1
2
3
2. Connect PSTN Land Line
1
2
1
2
3. Installation
1) Wall Mounting
Fix the wall mounting bracket on the wall with screws. Wedge the panel on the
bracket, make sure they t well.
2) Standing on the Desk
Mount the desktop bracket, and then put it on the desk.
3
1
2
Plug the output connector of AC adapter
into the adapter interface of control panel.
Plug the AC adapter to wall power socket.
S2 is a PSTN alarm system which will auto dial the
pre-stored phone number when the system
detects intruders.
Please make sure the panel has been
connected to PSTN land line to ensure safety.
Connect the smaller connector of provided telephone cable to the PSTN land line
interface at the back side of the pane.
Connect the other end of the telephone cable to the signal output
provided by PSTN land line operator.
Rear Side
Buzzer Tamper Switch Speaker
Backup Batteries
AC Adapter Interface
Power ON/OFF
PSTN Land Line Interface
Interfaces for
Wired Sensors
MIC
Output Wired Siren
(500mA)≤
Output for Electronic
Lock
NC Input for
Wired Sensor
(24H Zone)
NC Input for
Wired Sensor
(Normal Zone)

8
7
Control Panel Operation
1. Alarm Control
Arm (Away Arm)
Home Mode (Part Arm)
Disarm
Emergency Call
Hold the button for 3 seconds when the LCD
display is activated, the system goes into emergent
alarming state with siren hooting, meanwhile the
Panel will auto dial pre-stored alarm phone numbers.
[ ]
Input user code or admin code rst, then press
the button, the system enters Disarm
state when one beep is heard and the Disarm LED
Indicator lights on.
[Disarm ]
Press thebutton on the
control panel, the system enters Home Mode when
one beep is heard and the Home Mode LED
Indicator lights on. All the Normal Sensors are
armed except the Home Mode Sensors which
are disarmed so that users can move freely at home.
[Home Mode]
Press the button on the control panel,
the system enters Arm state when one beep is
heard and the Arm LED Indicator lights on.
[Arm ]
If Entry/Exit Delay is activated, all zones except the
24-hour zone will enter Arm state after the set delay
time.The Delay Sensors will enter Arm state after the
set delay time.
Note!
2. Access Control System
3. Dialing Calls
The control panel has a built-in call module. Make sure the PSTN land line
is connected and the credit is enough, you can use the panel to make calls.
When the control panel is in Disarm or Home Mode state, input the phone
number and pressbutton, the line will get through. If you input
wrong numbers, press button and input again. Press button to
cancel dialing or press button to end a conversation.
[Call ]
[Esc] [Esc]
[Call ]
4. Voice Memo
5. Function Setting
Input the admin code, and then press to enter setting menu.
Up Conrm
Down petstsalotkcaB
[Enter]
Enter
Esc
The control panel has a RFID reader for unlocking the electronic door lock
by disarming the system. Just place the RFID tag close to the RFID reader,
the green LED indicator ashes once.
The system is disarmed and the electronic door lock is open (If
connected).
Hold 3 seconds button to record 10 seconds voice message. The
Play Voice Memo circle will be ashing in blue to notify you. Users can
touch the center of circle to listen to the voice memo. The LED indicator
blacks out when the voice memo has been played. Replay by touching it
again.
[]

LCD Display Contents
System Status Display content
Stand-by
Arm or Disarm
Alarm
Line Disconnect
AC Power Failure
Panel Low Battery
System
Arm
System
Disarm
System
Home Arm
Remote
Arm
Remote
Disarm
Remote
Home Arm
RFID 1-50(RFID Name)
Disarm
Alarm
SOS
Alarm
Linecut
Alarm
Panel Tamper
Alarm
Sensor Tamper
Alarm
Wired Sensor
Alarm
Sensor 1-50(Sensor Name)
10
9
Wh
ent
L
A
en LCD is activated, input the admin code, and then press to
er setting menu.
[Enter]
CD Display Menu
Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3
ccessories
Alarm Number1-6
CMS Number1-2
Alarm Number1-6
CMS Number1-2
Add
Delete
Add
Delete
Edit Name
Add
Delete
Edit
Add Phone
Number
Del Phone
Number
Remote &
Keypad
RFID Tag
Wireless
Sensors
Test Mode
ALL
Remote (01-10)
ALL
RFID (01-50)
RFID (01-50)
ALL
Sensor (01-50)
Sensor (01-50)
Edit Sensor Type (Normal Sensor,
24 Hour Sensor, Delay Sensor,
Home Sensor)
Edit Sensor Name
Phone
Numbers

12
11
System
Settings
Date And Time
Entry Exit Delay
Backlight Time
<00S>
Auto Arm/
Disarm
Edit Welcome
Control by
Phone
Linecut Alarm
Keypad Tones
Access Code
Ringing Times
Date
Date Format
Time
Entry Delay <000S>
Exit Delay <000S>
Auto Arm Time
<00:00:00>
Auto Disarm Time
<00:00:00>
On
O
Admin Code
User Code
Duress Code
On
O
On
O
Input 6 Digits
<Default Code 123456>
Input 4 Digits
<Default Code 1234>
Input 4 Digits
<Default Code 1111>
Alarm Voice Record
Play
History
Siren Setup
User ID<1234>
Arm Upload
Disarm Upload
Reset
Wired Siren
Wireless Siren
Built-in Siren
Siren Alert Time
<300S>
Input 4 Digits
On
O
On
O
Siren Switch <On/O>
Arm/Disarm Tone <On/O>
Siren Switch <On/O>
Arm/Disarm Tone <On/O>
Siren Switch <On/O>
Arm/Disarm Tone <On/O>
Settings
1. Alarm Phone Number Setup
User can set 6 user phone numbers and 2 CMS phone numbers. When connecting to
CMS, system will dial CMS phone number to upload Contact ID reports while alarming
and then dial 6 user phone numbers in sequence one by one. System will dial all the user
phone numbers in 3 cycles until the phone is answered or any press on phone buttons.
Log on the menu, choose “Phone Numbers”, press .
Press or , choose“Add Phone Number”, press .
Press or , choose“Alarm Number1~6”, press .
Input alarm phone numbers in order, press. If group extended telephone number is
used, 0# or 9# need to be added in front of the phone number.
[Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
Add Alarm Phone Number
Delete Alarm Phone Number
Note!
If user wants to set CMS center phone number, please refer to“Connect to CMS Center”.
Log on the menu, choose “Phone Numbers”, press .
Press or , choose“Delete Phone Number”, press .
Press or , choose“Alarm Number1~6”, press .
Delete the alarm phone numbers in order, press again
[Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
1
2
3
4
When LCD is activated, input the admin code, and then press to enter setting
menu.
[Enter]
1
2
3
4
Log on the menu, press or , choose“Accessories”, press .
Press or , choose“Remote & Keypad”, press .
Press or , choose“Add”, press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
2. Add/Delete/Edit Accessories
Add/Delete Remote Controls or Wireless Keypads
Add
1
2
3
4
If user want to check or edit the stored phone number, enter “Alarm Number1~6”to
checkand edit.
Note!
The control panel only receives signal from accessories after they are connected to the
control panel.
LCD display will show “Please connect”, press any button from the remote control to
enable signal transmitting to the control panel. When a beep is heard, LCD display will
show “Remote (01-10)”, connection succeeded.

14
13
1
2
3
4
Log on the menu, press or , choose“Accessories”, press .
Press or , choose“RFID Tag”, press .
Press or , choose“Add”, press .
LCD display will show “Please connect”, put the RFID tag close to the RFID
reader on the control panel. When a beep is heard, LCD display will show
“RFID (01-50)”, connection succeeded.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
Delete
3
Add/Delete/Edit RFID Tags
Add
Note!
If three beeps is heard when coding , the accessory is coded already.
Delete
3
Edit
3
Add/Delete/Edit Wireless Sensors
1
2
3
4
Log on the menu, press or , choose“Accessories”, press .
Press or , choose“Wireless Sensors”, press .
Press or , choose“Add”, press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
Add
If user wants to delete the added remote controls or RFID wireless keypads,
please choose “Delete” in the step as above and press . Then
choose to delete all or specic remote controls or wireless keypads, press
again.
[Enter]
[Enter]
Note!
When adding wireless keypad to control panel, please enter access code and
then press "arm" or "disarm" button on the wireless keypad. When a "beep' is
heard, the keypad is successfully connected to the panel.
If user wants to rename the added RFID cards or tags, please choose “Edit
Name”in the step as above and press , then input the name. [Enter]
If user wants to delete the added RFID cards or tags, please choose “Delete”
in the step as above and press . Then choose to delete all or specic
RFID cards or tags, press again.
[Enter]
[Enter]
LCD display will show “Please connect”, trigger the detector once to make
it send wireless signal to the control panel. When a beep is heard, LCD
display will show “Sensor (01-50)”, connection succeeded.
1
2
3
4
5
6
Delete
3
Edit
Type of Sensors
Names of Sensors
5
1
2
3
Test Mode
Test if the sensors are connected successfully to the control panel.
Log on the menu, press or , choose“Accessories”, press .[ ] [ ] [Enter]
If user wants to rename the sensors, please choose “Edit Sensor Name” in the
step and press . Then input the sensor name.[Enter]
If user wants to delete the added sensors, please choose “Delete” in the
step as above and press . Then choose to delete all or specic
wireless sensors, press again.
[Enter]
[Enter]
Log on the menu, press or ,choose “Accessories”, press .
Press or , choose “Wireless Sensors”, press .
P r ess o r , choose “ E dit ”, p r ess .
Press or , choose “Sensor 01-50”, press .
Press or , choose “Edit Sensor Type”, press .
Press or , choose one type of “Normal Sensor/ 24 Hour Sensor/
Delay Sensor/ Home Sensor”, press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [En t er]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ]
[Enter]
Normal Sensor:
24 Hour Sensor:
Delay Sensor:
Home Sensor:
In armed mode, when normal sensors are triggered, alarm
system will alert. In disarmed mode, when normal sensors are triggered,
alarm system will not alert.
Under any circumstances, when 24 Hour Sensors are
triggered, alarm system will alert at once.
If user wants to use the entry and exit delay, related sensors
need to be set in entry and exit delay zone. When set is done, after set
delay time, those sensors will make system alert. Refer to Entry and Delay
Setup for details.
In home mode, only normal sensors will be triggered for
alarming while home sensors will not be triggered. This will allow user to
move freely at home.
Press or , choose “Test Mode”, press . LCD display will show
“Yes?”, Press again to start testing mode.
Please trigger coded sensors in order, the sensors will transmit signals to
control panel. When 3 beeps are heard, LCD display will show the
collected triggering occurences. Then you can count the correctly
connected sensors based on the numbers displayed on the LCD screen.
Exit by pressingbutton.
[ ] [ ] [Enter]
[Enter]
[Esc]

16
15
3. System Settings
3.1 Date and Time
1
2
Date Format
1
2
Time
The default time is on 24 hours standard.
1
2
Date
Note!
The entry and exit delay is only for delay sensors.
Press or , choose“Date and Time”, press .
Press or , choose“Date”, press .
Input date, press
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter].
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose“Date and Time”,press .
Pressor , .
Press or , .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
choose“Date Format”,press
choose format, press
Log on the menu, press or ,choose ”System Settings “ , press .[ ] [ ] [Enter]
Press or , choose“Date and Time”, press .
Press or , .
Input , press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
choose“Time”,press
current time
Log on the menu, press or , .[ ] [ ] [Enter]choose ”System Settings “ , press
3
4
3
4
3
4
3.2 Entry and Exit Delay
Entry Delay
If user is not used to taking along with the remote control, entry and exit delay
could be set in the system. Following is the operation instruction for arming
and disarming.
When entry and exit delay is set, user could exit the house in set time period,
then system will be armed automatically; when user is back without disarming
the system, entry delay will allow time for user to disarm the system.
Otherwise, the system will treat this as an intrusion and it will be triggered and
send out alarming alert.
Entry delay is set to give time to user for disarming the system before the
triggered sensors send signal to control panel after the set time.
Log on the menu, press or , choose“System Settings”, press .[ ] [ ] [Enter]
Press or , choose“Entry Exit Delay”, press .
Press or , choose“Entry Delay”, press .
Input time for entry delay; press for conrmation.
Entry delay time is calculated on seconds; default is 0 second (o ); setup
range is 0-999 seconds.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
1
2
3
4
Exit Delay
Log on the menu, press or , .[ ] [ ] [Enter]choose“System Settings”, press
1
2
3
4
Press or , choose“Entry Exit Delay”, press .
Press or , choose“Exit Delay”, press .
Input time for exit delay; press for conrmation.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
Log on the menu, press or , .[ ] [ ] [Enter]choose“System Settings”, press
1
2
3
4
Press [ ] or [ ] , choose“Backlight Time”, press [Enter].
Input time for backlight time; press [Enter].
Backlight time is calculated on seconds; default is 20 seconds; setup range is
01-99 seconds.
3.3 Backlight Time
3.4 Timed Arm / Disarm
User can set timed arm and disarm according to daily schedule to
avoid repeated operation.
Timed Arm
1
2Press or , choose“Auto Arm/Disarm”, press .
Press or , choose“Auto Arm Time”, press .
Input exact time for arming; press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
3
4
Exit delay is set to give time to user for arming the system and then exit
within the set time.
Exit delay time is calculated on seconds; default is 0 second (o );
setup range is 0-999 seconds.
Once delay time is set, when arm the system, one beep will be heard every
second to remind the user to leave, the reminding rhythm willspeed up in
the last 15 seconds.
User can set standby time for the backlight on the blue LCD display
accordingly.
Log on the menu, press or ,
.
[ ] [ ]
[Enter]
choose “System Settings”,
press

18
17
Remote Phone Control Instruction Table
Turn On/O Line Cut Alarm
1
2
3
Press or , choose“Linecut Alarm”, press .
Press or , choose“On” or “O”, press .
“On” is to turn on the linecut alarm; “O” is to turn o the linecut alarm. Default
setting is“On”, the linecut alarm is on.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
Phone
Buttons Function Explanation
][sserP
][sserP
][sserP
][sserP
][sserP
][sserP
][sserP
][sserP
Arm the system
Disarm the system
Monitor on site
Turn on siren
Turn o siren
Turn on relay
Turn o relay
To exit Remote Phone Control
Phone voice prompt“Arm Succeed”
Phone voice prompt“Disarm Succeed”
Press [*] to prolong monitor time
Deter the intruders
Siren stops ringing
Available for the system with RS-1000
relay module
Or hang up the phone
User can turn on/o keypad tone accordingly.
1
2
3
4
4
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Turn On/O Keypad Tone
Log on the menu, press or ,
.
[ ] [ ]
[Enter]
choose “System Settings”, press
Press or , choose“Keypad Tone”, press .
Press or , choose“On” or “O”, press .
“On”is to turn on the keypad tone; “O” is to turn o the keypad tone. Default
setting is“On”, keypad tone is on.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
3.8 Keypad Tone
Timed Disarm
1
2
3
4
Press or , choose “Auto Arm/Disarm”, press .
Press or , choose “Auto Disarm Time”, press .
Input exact time for disarming; press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
1
2
3.5 Edit Greeting Message
3.6 Remote Phone Control
Turn On/O Remote Phone Control
1
2
3
Remote Phone Control Operation
Method 1
Method 2
User dials alarm system telephone number; after getting through, alarm
system will guide you to input access code.
Input access code (user code or admin code); Press [ ].
Alarm system plays the voice prompt twice to explain the functions.
Userchooses the related instruction to make remote control operation.
Instruction Table Below)
1
2
3
4
Note!
Alarm system will hang up after 30 seconds with no operation.
Log on the menu, press or , choose “System Settings”, press
for conrmation.
[ ] [ ]
[Enter]
When greeting message is set; turn on the alarm system or activate the
touch keyboard; the greeting message will be shown on LCD display.
Log on the menu, press or , choose “System Settings”, press
.
Press or , choose “Edit Welcome”, press to dene the
greeting message. means to delete, means to space, means
to move backward, means to move forward.
[ ] [ ]
[Enter]
[ ] [ ] [Enter]
[ ] [ ] [ ]
[ ]
Users can set to turn on/o remote phone control to get free access to
the alarm system for arming, disarming and on site monitoring by dialing
telephone number of the system.
Log on the menu, press or , choose “System Settings”, press
.
Press or , choose “Control by Phone”, press .
Press or , choose “On” or “O ”, press .
“On”is to turn on phone remote control; “O” is to turn o phone remote
control.
Default setting is “o”, Remote Phone Control o.
[ ] [ ]
[Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
When alarm system is triggered, the control panel will dial pre-stored user
phone numbers. When pick up the phone, users can follow the prompt
voice to control the panel remotely after recorded voice is heard. (See
Instruction Table Below)
3.7 Linecut Alarm
When linecut alarm function is on, the control panel will alert once the PSTN land
line is cut or pulled out.
(See

All the alarm panels are with default user code, admin code and duress
code. Please change all codes before using and keep your codes secret.
Admin Code
1
2
3
4
With admin code, user can arm and disarm, make system settings as well
as reset codes etc.
Log on the menu, press or , .[ ] [ ] [Enter]choose“Syetem Settings”, press
Press or , choose“Access Code”, press .
Press or , choose“Admin Code”, press .
LCD display will show “Input 6 Digits”, then input 6 digits for code, press
.(Default Admin Code: 123456)
Input the new admin code, press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
[Enter]
5
1
2
3
4
User Code
With user code, user can set arm, home mode and disarm the alarm system.
Log on the menu, press or , .[ ] [ ] [Enter]choose“Syetem Settings”, press
Press or , choose“Access Code”, press .
Press or , choose“User Code”, press .
LCD display will show “Input 4 Digits”, then input 4 digits for code, press
.(Default User Code: 1234)
Input the new user code, press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
[Enter]
5
1
2
3
4
Duress Code
In case of emergency, when user is violently requested to disarm the system, it's
recommended to use the duress code to disarm the alarm system. The panel will
silently dial stored alarm telephone numbers.
Log on the menu, press [ ] or [ ] , choose“System Settings”, press [Enter].
Press or , choose“Access Code”, press .
Press or , choose“Duress Code”, press .
.(Default Duress Code: 1111)
Input the new duress code, press .
[ ] [ ] [Enter]
[ ] [ ] [Enter]
LCD display will show“Input 4 Digits”, then input 4 digits for code, press
[Enter]
[Enter]
5
3.10 Ringing Times for Remote Phone Control
After the ringing times setting, user can send commands from remote calling,
such as arming/disarming the system.
1
2
Log on the menu, press or , .[ ] [ ] [Enter]choose“System Settings”, press
Press or , choose“Ringing Times”, press .
Input 5~9 for ring times, press .
Default setting is 5 times.
[ ] [ ] [Enter]
[Enter]
3
3.11 Alarm Voice
1
2
3
4
5
20 19
3.9 Access Code
1
2
3
4
Record Alarm Voice
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose “Alarm Voice”, press .
Press or , choose “Record”, press .
LCD display will show “Record 10s Voice”to remind you of the 10 seconds
voice recording, press .
Start voice recording for 10s until the system stops automatically, or press
to stop recording.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
[Enter]
Play Recorded Voice
Log on the menu, press or , .[ ] [ ] [Enter]choose“System Settings”, press
Press or , choose“Alarm Voice”, press .
Press or , choose“Play”, press .
The voice record will be played automatically.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
3.12 Siren Setup
Wired Siren
Wired siren is connected to the control panel by wire.
Turn On/O Wired Siren
Log on the menu, press or , press
.
[ ] [ ]
[Enter]
choose “System Settings”,
Press or , choose“Siren Setup”, press .
Press or , choose“Wired Siren”, press .
Press or , choose“Siren Switch”, press .
Press or , choose“On” or “O”, press
“On”is to turn on the wired siren; “O” is to turn o the wired siren. Default
setting is“On”; the wired siren is on.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
1
2
3
4
5
User can leave 10 seconds voice message when control panel makes call to
user's stored phone number, voice record will be repeatedly played to notify
the intrusion.
Users can turn on/o wired siren, wireless siren, built-in siren as well as
arm/disarm beep, and set siren ringing time.

22
21
3.16 Reset
Note!
All system settings will be restored to default setting. Reset will not delete the
accessories that has already been coded to the control panel.
1
2
Log on the menu, press or , .[ ] [ ] [Enter]choose “System Settings”, press
Pressor, choose “Reset”, press to reset the system to
default setting.
[ ] [ ] [Enter]
Turn On/O Arm/Disarm Beep for Built-in Siren
Log on the menu, press or , .[ ] [ ] [Enter]choose “System Settings”, press
Press or , choose “Siren Setup”, press .
Press or , choose “Built-in Siren”, press .
Press or , choose “Arm/Disarm Beep”, press .
Press or , choose “On” or “O”, press
“On” is to turn on arm/disarm beep for built-in siren; “O” is to turn o
arm/disarm beep for built-in siren. Default setting is “On”; arm/disarm
beep is on.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
1
2
3
4
5
Siren Ringing Time
Set Ringing Time for All Sirens
Press or , choose “Siren Setup”, press .
Press or , choose “Siren Alert Time”, press .
Input the ringing time, press .
Siren ringing time is calculated as seconds, default setting is 300 seconds.
If 0 second is set, siren will not ring
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
Log on the menu, press or , .[ ] [ ] [Enter]choose“System Settings”, press
1
2
3
4
Please see details at Page 23: Connect to CMS
3.14 Upload Arm Report
Please see details at Page 23: Connect to CMS
3.15 Upload Disarm Report
Please see details at Page 23: Connect to CMS
If user forgot the admin code and cannot setup the system, please contact local
distributors.
Check Event Logs
1
2
3
Log on the menu, press or , choose “ History”, press .[ ] [ ] [Enter]
Users can check the event logs freely. 150 event logs are traceable.
Press or , choose the event log you need to track, press .
Relevant event log time and alarm way will be shown.
[ ] [ ] [Enter]
3.13 User ID for CMS
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Turn On/O Arm/Disarm Beep for Wired Siren
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Pressor,choose“Siren Setup”, press .
Pressor,choose“Wired Siren”, press .
Pressor,choose“Arm/Disarm Beep”, press .
Press or , choose“On” or “O”, press
“On”is to turn on arm/disarm beep for wired siren; “O” is to turn o arm/
disarm beep for wired siren.
Default setting is“On”; arm/disarm beep is on.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
Wireless Siren
Wireless siren is connected to control panel through wireless connection.
Turn on/o wireless siren
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose“Siren Setup”, press .
Press or , choose“Wireless Siren”, press .
Press or , choose“Siren Switch”, press .
Press or , choose“On” or “O”, press
“On”is to turn on the wireless siren; “O” is to turn o the wireless siren.
Default setting is“On”; the wireless siren is on.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
Turn On/O Arm/Disarm Beep for Wireless Siren
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose“Siren Setup”, press .
Press or , choose“Wireless Siren”, press .
Press or , choose“Arm/Disarm Beep”, press .
Press or , choose“On” or “O”, press
“On” is to turn on arm/disarm beep for wireless siren; “O” is to turn o
arm/disarm beep for wireless siren.
Default setting is “On”; arm/disarm beep is on.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
Built-in Siren
Built-in siren is the siren inside the control panel
Turn On/O Built-in Siren
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose“Siren Setup”, press .
Press or , choose“Built-in Siren”, press .
Press or , choose“Siren Switch”, press .
Press or , choose“On” or “O”, press
“On”is to turn on the built-in siren; “O” is to turn o the built-in siren.
Default setting is“On”; the built-in siren is on.
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
1
2
3
4
5

24
23
Contact ID Reports
Arm
Disarm
Disarm by RFID tag
PIR detector alarm
Door contact alarm
Emergency call
Duress alarm
Home mode (part arm)
Control panel tamper alarm
Sensor tamper alarm
Normal zone alarm
24H zone alarm
Sensor low battery
Control panel low battery
Control panel AC failure
Event Code Event Event Event Code
3401
1401
1409
1132
1131
1100
1120
3456
1137
1144
1140
1133
1384
1302
1301
Precautions
To prevent ha rm to users or o ther peop le dur ing usage o f the produc t and to
extend th e li fesp an of th e p roduc t, please fol low the p recauti ons below :
General Instruction
The wireless accessories should be connected to the control panel before use.
Low power voltage would aect transmitting distance range.
2 cells of 3.7V/800mAh battery backup or standard power adapter for power supply.
All accessories from our company are compatible with this control panel.
Do not press SOS key if there is no emergency to avoid disturbing neighborhood.
Check the system regularly to ensure the system works properly in case of emergency.
The control panel is neither waterproof nor moisture-proof, please install it in a shady,
cool and dry place.
The case of the control panel is made of ABS. Please keep it away from strong light
for a longer lifespan.
Forbiddance
The control panel is non explosion-proof. Please keep it away from re, ame sources.
Install the control panel away from objects such as heater, air conditioner, microwave
oven etc. that produces heat or electric-magnetic.
Forbiddance of Decomposition
Take the control panel for disposal of recycling according to the local regulation.
Disassembly for this product can not be done by non-professionals.
Connect to Electronic Lock
Please ignore this if user is not intended to put this alarm as access control. This alarm
only sends on/o signal to electronic door lock, please refer to related electronic door
lock manual for details.
Connect to CMS Center
Please ignore this step if users don't need to connect to CMS center. When connected
to CMS center, control panel will upload contact ID to CMS center automatically once
intrusion is detected.
Add CMS Phone Number
When CMS center phone number is stored, the control panel will auto dial to CMS center
automatically when alarm.
1
2
3
4
Press or , choose “CMS Number1”or“CMS Number2”, press .[ ] [ ] [Enter]
Input CMS phone no, press . If group extension telephone number
is used to connect to the CMS center, please add 0# or9# before the phone
number you plan to store.
Log on the menu, choose “Phone Numbers”, press .[Enter]
Press or , choose“Add Phone Number”, press .[ ] [ ] [Enter]
[Enter]
Note!
If user wants to check or edit the pre-stored phone no., enter“CMS Number
1~2” to check or edit.
Delete CMS Phone Number
1
2
3
4
Log on the menu, choose “Phone Numbers”, press .
Press or , choose“Del Phone Number”, press .
Press or , choose in order “CMS Number1~2”, press .
Delete stored CMS phone no., Press .
[Enter]
[ ] [ ] [Enter]
[ ] [ ] [Enter]
[Enter]
1
2
3
User ID
It is supplied by CMS center. After it is stored, CMS center can exactly know user’s
location according to the ID number.
Log on the menu; press or , choose“System Settings”, press .[ ] [ ] [Enter]
Press or , choose“User ID”, press .
LCD display will show“Input 4 Digits”, input 4 digits user ID, press .
[ ] [ ] [Enter]
[Enter]
Upload Arm/ Disarm Report to CMS Center
1
2
3
When this function is enabled, all arm/disarm reports will be uploaded
automatically to CMS center, so that CMS center can know the status of the alarm
system.
After the User ID is set, press or to choose “Arm Upload”or
“Disarm Upload”, press .
Press or , Choose“On”, press .
When choosing“O” during setup , press , arm/ disarm report
will not be uploaded to CMS center.
[ ] [ ]
[Enter]
[ ] [ ] [Enter]
[Enter]
2

26
25
FAQ
Phenomena Cause of Malfunction Troubleshot Method
No response from
control panel
operation
Accessories cannot
connect to control
panel
No response from
the control panel
by operating
remote control
RFID card/tag fail
to disarm
Touch keyboard fail
to make related
setting
Power switch is o
A/C Power failure
Lithium battery backup
power exhausted
Panel not in learning
status
Accessories not triggered
for learning
When learning, 3 beeps
are heard from panel
Remote control is not
learned to control panel
Out of range between
remote control and panel
RFID card/tag not connected
to the panel
Not logged onto the
setting menu.
Open battery compartment,
turn on the power
Contact local main power
supply bureau
Connect to main power with
adapter
Make sure the panel set in
learning status
Make sure the triggered
accessories transmit signal
to panel for learning
This means accessory has
been coded already
Follow the manual and connect
the remote control to panel
No more than 80 meters in
open area
(no interference)
Signal repeater could be added
Follow the work manual and
code RFID card/tag to the panel
Input the correct admin code,
press and log on menu
setting
[ Enter ]
Specications
Product Name
Model No.
Power Supply
Standby Current
Alarm Current
Backup Battery
Internal Siren Volume
Radio Frequency
PSTN/LCD/RFID Touch Alarm System
S2
Input: AC 110V-240V, 50/60Hz
Output: DC 12V 500mA, 6Wh
≤ 90mA
≤ 300mA
2 Cells of 3.7V 800mAh Li-ion Battery(BL-5B)
95dB
315MHz or 433MHz (±75KHz)
Maximum Stored Phone No.
Maximum Remote Controls
Maximum Sensors
Maximum RFID Tags
Maximum Event Logs
Housing Material
Operation Condition
Dimension (L x W x H)
6 alarm Phone No. and 2 CMS No.
10 pcs
50 pcs
50 pcs
150 events
ABS plastic
Temperature: -10°C~ 55°C
Humidity: 80%RH (non-condensing)
185x130x27mm
Wireless Remote Control
LED Indicator
Disarm
Arm
Stay
Panic
Arm
The delay sensors will be armed after delay time.
Press button on the remote control, the system enters Arm state
when one beep is heard and the Arm LED Indicator lights on.
mrA ][
Note! If Exit Delay is activated, all zones except the 24-hour zone will
enter Arm state after the set delay time.
Disarm
Press the [Disarm ] button on the remote control, the system enters
Disarm state when two beeps are heard and the Arm LED Indicator goes
out.
When alarm is activated, the siren will hoot. Press the button,
the system is disarmed after two beeps are heard, and the Disarm LED
Indicator lights on. But the LED indicator of triggered zone keeps ashing
for further checking.
Press button again, the alarming zone indicator goes out.
[Disarm ]
[Disarm ]
Home Mode
Press button on the remote control, the system enters Home
Mode when one beep is heard and the Home Mode LED Indicator lights on.
All the Normal Sensors are armed except the Home Mode Sensors which
are disarmed so that users can move freely at home.
[ Stay ]
Mute Mode
Emergency Call
In any condition, once the button on the remote control is pressed,
the system goes into emergent alarming state with siren hooting,
meanwhile the panel will autodial pre-stored alarm phone numbers.
SOS ][
When arm or disarm the system, the control panel will beep once or twice.
If siren beep is not needed, operationas follows :
Press button on the remote control, then press
or button. The system is armed or disarmed in mute without
disturbing other people.
[] [Arm ]
[Disarm ]
Stay

28
27
Wireless Door Window Contact/
Appearance
Features
LED indicator
Transmitter Magnet
AA 1.5V LR6
LED Indication
Tamper switch
PCB Layout
LED ashes once:
Door/window is opened and transmitter sends signal to the control panel.
Low power indication, please change battery as soon as
possible.
LED ashes quickly(after triggered):
Note!
Tamper switch only works when the system is in Arm State.
Installation & Notice
Remove the battery activation strip, the sensor
will enter working state immediately.
Mount the sensor on the door frame and the
magnet on the door.
Make sure the magnet is on the right side of
the transmitter.
Place the transmitter in the desired location,
mount the magnet no more than 1cm away
from the transmitter and secure transmitter
and magnet with double-sided tapes or screws.
Avoid mounting sensors in areas with a large
quantity of metal or electrical wiring, such as
a furnace or utility room.
Specications
Power supply
Static current
Alarm current
Transmitting distance
Radio frequency
DC 1.5V (AA 1.5V LR6 Battery x 1pc)
≤ 30uA
≤ 40mA
≤80m (in open area)
315MHz or433MHz (±75KHz)
Housing material
Operating Condition
Transmitter dimensions (LxWxH)
Magnet dimensions (LxWxH)
ABS plastic
Temperature -10°C~55°C
Relative humidity ≤80%RH (non-condensing)
71 x 34 x 17.5mm
51 x 12 x 13.5mm
Appearance
1
23
1. Detection window
2. LED indicator
3. Bracket
Wireless PIR Motion Detector
LED Indication
Flash continuously:
Flash once:
Flash twice:
Under the self-testing state.
Intruder is detected.
Self-testing is nished, enters
batteries immediately.(User will get alert SMS about the low battery if the PIR detector is connected
to the GSM alarm system.)
PCB Layout
AA 1.5V LR6 AA 1.5V LR6
Infrared sensor
LED ON / OFF
Tamper switch
Infrared sensor:
Tamper switch:
It detects
touch the surface and always keep it clean.
Once the case is opened in working state, the tamper switch will be
triggered and then generates an alarm signal.
the infrared rays released by human body motion, please don’t
The SAC-03 is a Door/Window Contact that can be installed on doors, windows, and any other
objects that open and close. The sensor transmits signals to the control panel when a magnet
mounted near the sensor is moved away. External input for wired accessory is available at the
N/C interface. The tamper protection ensures that sabotage attempts to move the contact will
result in an alarm activation.
Features
SAC-01 is a high performance wireless P.I.R. motion detector. It consists of digital dual-core
fuzzy logic infrared control chip and intelligent analysis which eectively identify interference
signals from body movement signals and reduce false alarm rate. With automatic
temperature compensation and anti-air turbulence technology, it easily adapts to
environmental changes. The detector also has the advantages of energy saving, reliability
and easy installation.

30
29
Usage
Remove the battery activation strip to activate batteries. It will start self-testing
for one minute.
Mode Setting
Test Button
Connect to alarm panel
Press the connect key on the alarm panel, and then press the test button of the
sensor twice to send alarm signal. When one beep is heard, they are connected. To
check if they are connected successfully, arm the system, and trigger the sensor
again, if there is an alert, the connection is successful.
2m
Ground
The detector is more sensitive to the cross movement than to the vertical
movement, so th e per forma n ce of de tec to r is best wh e n th e de tec tion
direction is vertical to the walking direction of people.
Installation & Notices
Avoid mounting the detector close to windows, air conditioner, heater, refrigerator,
oven, sunshine and places where the temperature changes fast or the air stream ows
frequently.
If two detectors are installed in the same detection scope, please adjust the locatio to
avoid interference and false alarm.
Top view Side view
Testing (Walk Test)
A. After installation, power on the detector. After one minute self-testing, press the
test button, walk in the scope (from left to right or from right to left) and watch the
LED indicator to make sure the detector is working.
B. The LED indicator ashes once when body movement is detected.
C. Adjust the detector angle accordingly to achieve the best detection eect.
Testing mode:
After self-testing, press the test button, the sensor enters testing mode, and
detects once every 10 seconds. After 3 minutes, the LED ashes twice, and the
sensor enters the working mode.
Working mode:
In working state, if the sensor is triggered twice within 3 minutes, it will enter
sleeping mode to save power. After no movement within next 3 minutes, the
sensor goes back to the working mode.
Fix the bracket on the wall with screws and attach the detector to the bracket.
Adjust installation height or bracket to change the detection distance and
angle. It is recommended to mount it at the height of 2m from the ground.
Directive
Detection Scope
2m 4m 6 m 8m0m
0m
2m
110°
Top viewSide view
Specications
Power supply
Static current
Alarm current
Detection scope
Transmitting distance
DC 3V (AA 1.5V LR6 Battery x 2 pcs)
≤ 50uA
≤ 9.5mA
8m/110°
≤ 80m (in open area)
Radio frequency
Housing material
Operation Condition
Detector dimensions (L x W x H)
Bracket dimensions (L x W x H)
315MHz or 433MHz (± 75KHz)
ABS plastic
Temperature: -10°C~55°C
Humidity: ≤80%RH (non-condensing)
108 x 52 x 36.8 mm
52 x 30 x 26.5 mm
This product bears the selective sorting symbol for waste electrical and electronic
equipment(WEEE).This means that this product must be handled pursuant to European.
2002/96/EC in order to be recycled or dismantled to minimize its impact on the environment.
For further information,please contact your local or regional authorities.
Electronic products not included in the selective sorting process are potentially dangerous for
the environment and human heath due to the presence of hazardous substances.
In compliance with European’s law.
This product was designed and manufactured in compliance with Directive 2002/95/EC of the
European Parliament and of the Council on the restriction of use of certain hazardous substances in
electrical and electronic equipment (RoHS Directive - Rohs) and is deemed to comply with the
maximum concentration values set by the European Technical Adaptation Committee(TAC).
Standards

Caractéristiques
34 ~35
33 ~34
42 ~52
53 ~54
40 ~41
58 ~60
57 ~58
37 ~38
36
39
53
54
55
55
56
32
31
PSTN/LCD/RFID
Système d'alarme tactile
FR Veuillez lire attentivement ce manuel
avant d’utiliser votre système d’alarme.
Veuillez conserver ce manuel
d’utilisation pour une éventuelle
consultation ultérieure.
Conguration sans l, à installer soi-même en toute simplicité
Design élégant avec clavier tactile numérique
Écran LCD avec menu de navigation, facile à programmer
Processeurs ARM + Auror de haute qualité
1 000 000 de combinaisons de codes radio intégrés pour une grande abilité
Utilisable avec 10 télécommandes, 50 détecteurs sans l et 50 badges RFID
Mémorisation de 6 numéros de téléphone d'alarme et 2 numéros de centre de surveillance
10 secondes de mémos vocaux et message vocal d'alarme enregistrable
Désarmement du système par badge RFID et déverrouillage de la porte électronique
Faible consommation d’énergie et alarme anti-sabotage pour les détecteurs sans l
Jusqu’à 150 journaux d'événements d'alarme pris en charge
Appels passés directement depuis le panneau de contrôle
Armement, désarmement et surveillance à distance par une simple opération téléphonique
Le code sous contrainte permet d’envoyer une notication d’alarme en toute discrétion
Programmation de l’armement et du désarmement
Prise en charge des délais d’entrée et de sortie
Possibilité de renommer toutes les zones et badges RIFD
Contrôle à distance par téléphone guidé par des commandes vocales
Table des matières
Accessoires inclus
Présentation du panneau de contrôle
Préparation en vue de l’utilisation
Mise sous tension
Raccordement à la ligne téléphonique (réseau RTC)
Installation
Utilisation du panneau de contrôle
Contrôle de l’alarme
Accès au système de contrôle
Composition des appels
Mémo vocal
Réglage des fonctions
Contenu de l’écran LCD
Menus de l’écran LCD
Conguration
Conguration des numéros de téléphone d'alarme
Ajouter / Supprimer/ Modier des accessoires
Conguration système
Date et heure
Délai d’entrée et de sortie
Durée du rétro-éclairage
Armement / Désarmement automatique
Modication du message d’accueil
Alarme ligne téléphonique déconnectée
Tonalité des touches du clavier
Codes d’accès
Nombre de sonneries avant contrôle à
distance par téléphone
Message d'alerte
Conguration des sirènes
Vérier les journaux d'événements
Connexion de la serrure électronique
Connexion au centre de surveillance
Ajouter un numéro de téléphone de centre de surveillance
Supprimer le numéro de téléphone de centre de surveillance
Identiant utilisateur
Transmettre le rapport d’armement/désarmement au centre de surveillance
Rapports des identiants de contact
Précautions
Foire aux questions
Caractéristiques techniques
Télécommande sans l
Détecteur d'ouverture sans l
Détecteur de mouvement sans l

Vis x 6
Guide
d’utilisation x 1
Mode Maison
Désarmement
Armement
Touche mémo vocal
Témoin lumineux
Écran LCD
Échappe
Haut/Bas
Entrer
SOS
Eacer
Appel
Vue frontale
Présentation du panneau de contrôle
34
33
Accessoires inclus
S2 Panneau de contrôle x 1
Télécommande sans l x 2
La télécommande est compacte et
portative. Il est recommandé de
l’emporter avec soi pour armer,
désarmer ou armer partiellement le
système d'alarme ou pour passer un
appel d'urgence.
Badge RFID x 2
Le badge RFID permet de désarmer le
système et de déverrouiller la serrure
électronique (si connectée).
Câble téléphonique x 1
Connecter la ligne téléphonique
(réseau RTC) au panneau de contrôle.
En cas d'urgence, le panneau
déclenche la sirène sur place et appelle
le numéro de téléphone d'alarme
mémorisé pour avertir les utilisateurs.
Le panneau de contrôle est connu comme le « cœur et le
cerveau » du système d'alarme. Il sert à recevoir et traiter
les signaux provenant des détecteurs sans l et des
télécommandes. Les utilisateurs peuvent le congurer
facilement grâce au clavier et à l'écran LCD. En cas
d'urgence, le panneau déclenche la sirène sur le site et
compose automatiquement les numéros de téléphone
d'alarme mémorisés. Lorsque les utilisateurs décrochent le
téléphone, ils entendent un message vocal d'alarme et ont
la possibilité d’activer la surveillance du site ou de
désarmer le système.
Détecteur d'ouverture sans l x 2
Le détecteur d'ouverture peut être installé sur les portes,
fenêtres ou tout autre dispositif pouvant s’ouvrir et se fermer.
Le détecteur envoie des signaux au panneau de contrôle
lorsque l’aimant monté à proximité de l'émetteur s’éloigne.
Détecteur de mouvement sans l x 2
Le détecteur de mouvement sans l est un
détecteur de mouvement infrarouge passif
intelligent, conçu pour détecter les
mouvements humains dans un périmètre de 6
à 8 mètres environ. Le détecteur est doté d’une
logique oue numérique pour réduire les
fausses alarmes dues à des sources de chaleur
indésirables. Grâce à sa fonction d'économie
d'énergie, le détecteur se met en veille dans les
3 minutes après la seconde activation.
Détecteur d'ouverture sans l x 2
Le détecteur d'ouverture peut être installé sur
les portes, fenêtres ou tout autre dispositif
pouvant s’ouvrir et se fermer. Le détecteur
envoie des signaux au panneau de contrôle
lorsque l’aimant monté à proximité de
l'émetteur s’éloigne.
Supports (mural ou de
bureau) pour le
panneau de contrôle x 2
Support pour le
détecteur de
mouvement PIR x 2
Ruban adhésif double
face pour le détecteur
d'ouverture x 2
Lecteur de badge RFID /
Lecture des mémos vocaux

36
35
Préparation en vue de l'utilisation
1. Mise sous tension
1
2
3
2. Raccordement à la ligne téléphonique (réseau RTC)
1
2
1
2
3. Installation
3
1
2
Vue postérieure
Buzzer
Batteries de secours
Interface d'alimentation
Mise sous tension /
Mise hors tension
Interface de raccordement
à la ligne téléphonique
(réseau RTC)
Microphone
Interrupteur
anti-sabotage Haut-parleur
Interface de raccordement
des détecteurs laires
Sortie pour sirène laire
(≤500mA)
Sortie pour serrure
électronique
Interface détecteur
laire (Zone 24 h)
Interface détecteur
laire (Zone normale)
Brancher le connecteur de sortie de
l'adaptateur secteur dans l'interface
d'alimentation du panneau de contrôle.
Brancher l'adaptateur secteur à la prise murale.
Mettez le bouton de mise sous tension en
position ON.
Le S2 est un système d'alarme connecté au réseau RTC
qui compose automatiquement le numéro de
téléphone mémorisé lorsqu’une intrusion est détectée.
Veuillez vous assurer que le panneau de contrôle
est bien raccordé à la ligne téléphonique pour
garantir votre sécurité.
Raccorder le plus petit connecteur du câble téléphonique fourni à l'interface de la
ligne téléphonique située à l’arrière du panneau de contrôle.
Raccorder l'autre extrémité du câble téléphonique à la sortie du signal fournie par
l'opérateur de la ligne téléphonique.
1) Montage au mur
Fixer le support mural sur le mur avec des vis. Fixer le panneau sur le support et
s’assurer qu’il est bien intégré.
2) Montage sur un bureau
Monter le support pour bureau puis installer le panneau sur le support.

38
37
Utilisation du panneau de contrôle
1. Contrôle de l’alarme
Armement (utilisateurs à
l’extérieur)
Mode Maison
(Armement partiel)
Disarm
Emergency Call
2. Accès au système de contrôle
3. Composition des appels
4. Mémo vocal
5. Réglage des fonctions
[Enter]
[Arm ]
Appuyer sur la touche du panneau de
contrôle. Le système est armé lorsque vous
entendez un bip et que le témoin lumineux de
l’armement s’allume.
Attention !
Si un délai d’entrée et de sortie est activé, le
système passera en mode Armement dans toutes
les zones, à l'exception de la zone 24 h, après la
durée du délai dénie. Les détecteurs fonction-
neront dès ce délai passé.
[Home Mode]
Appuyer sur la touche du panneau
de contrôle. Le système passe en mode Maison
lorsque vous entendez un bip et que le témoin
lumineux du Mode Maison s’allume. Tous les
détecteurs normaux sont armés à l’exception des
détecteurs de la zone Mode Maison an que les
utilisateurs puissent se déplacer librement chez eux.
[Disarm ]
Saisir le code d'utilisateur ou le code administrateur
puis appuyer sur la touche . Le système
est désarmé lorsque vous entendez un bip et que le
témoin lumineux de désarmement s’allume.
[ ]
Maintenir enfoncée pendant 3 secondes la touche
.lorsque l’écran LCD est allumé. Le système
entre en état d’alerte et la sirène retentit. Pendant
ce temps le panneau de contrôle appelle
automatiquement les numéros de téléphone
mémorisés.
Le panneau de contrôle est équipé d’un lecteur de badge RFID pour le
déverrouillage de la serrure électronique de la porte lorsque vous
désarmez le système. Il sut de placer le badge à proximité du lecteur
RFID, le témoin lumineux vert clignote une fois.
Le système est désarmé et la serrure électronique de la porte est
déverrouillée (si connectée).
[Esc]
[Esc]
[Call ]
[Call ]
Le panneau de contrôle est équipé d’un module d’appel intégré.
Assurez-vous de bien avoir raccordé la ligne téléphonique (réseau RTC)
au panneau de contrôle et de disposer d’un crédit d’appel susant pour
pouvoir utiliser cette fonction.
Lorsque le panneau de contrôle est en mode Désarmement ou en mode
Maison, composez un numéro de téléphone et appuyez sur la touche
pour passer un appel. En cas d’erreur de saisie, appuyez sur
et recomposez le numéro. Appuyez sur pour annuler la numérotation
ou sur la touche pour raccrocher.
Saisissez le code administrateur, puis appuyer sur pour entrer
dans le menu de conguration.
[]
Appuyez 3 secondes sur la touche pour enregistrer un message
vocal de 10 secondes. Le cercle Lecture du mémo vocal clignote en
bleu pour notier un message. Les utilisateurs peuvent écouter le
mémo vocal en touchant le centre du cercle. Le témoin lumineux
s'éteint après la lecture du mémo vocal. Vous pouvez le réécouter en
appuyant à nouveau sur le centre du cercle.
Bas
Enter
Esc
Haut Conrmer
Retour à l’étape précédente