eTIGER S4 Cell + Line User manual

www.etiger.com EN
Quick Start Guide
Security Kit - S4 Cell + Line

How do you wish to interact with your control panel?
- Using a landline connection enables a basic interaction with
your alarm system (by phone call).
- Using a SIM card (sold separately) enables a more advance
interaction with your system (by phone call, SMS or app).
- Using both the SIM card and the landline connection oers
an optimal security, as you always have a backup in case your
landline or your cellular network is down.
If you do not wish to use a SIM card, go directly to step 4.
1
Landline or SIM card?

Disable the security of your control panel’s SIM card
The control panel of the Security Kit can interact with you
thanks to a SIM card (sold separately). Before inserting your
SIM card in the control panel, make sure the SIM security is
o. To do so, insert the SIM card in a mobile phone, browse
the settings of the phone and disable the SIM security (if the
SIM security is activated, the PIN code will be required).
A piece of advice
For your control panel’s SIM card, we advise you to choose a
plan with unlimited text and 1 or 2 hours of call.
2
Settings
SIM PIN
Request a PIN code to
unlock the phone.
O
This step only applies if you are using your system with a SIM card.
Control panel’s
SIM card

SIM
3
This step only applies if you are using your system with a SIM card.
Insert the SIM card in the control panel
Open the battery compartment at the back of your control
panel and insert the SIM card in the SIM card slot.
Important
- Insert the SIM card according to the shape of the SIM card
slot.
- The SIM card must be compatible with the GSM network.
Contact your carrier for more information.
If you do not wish to connect your system to a landline, go
directly to step 5.

Connect the control panel to your landline
1. Connect the smaller connector of the telephone cable
(supplied in your kit) to the landline interface in the battery
compartment at the back of the control panel.
2. Connect the other end of the telephone cable to the your
landline socket or to the phone connector of your ADSL box.
4
This step only applies if you wish to connect your system to a landline.

Turn the control panel on
Plug the AC adaptor to an AC socket. Plug the output
connector of the AC adaptor into the adaptor interface in
the battery compartment at the back of the control panel.
Turn the power switch to “ON” and put back the cover of the
battery compartment. The control panel is turning on.
Important
Before turning your control panel on, make sure you have
either inserted a SIM card or connected it to your landline.
5

6
Mount the control panel on a wall
Screw the wall mount onto the wall where you wish to install
your control panel. Fix the control panel on the wall mount.
Some advice
- Make sure the control panel is rmly xed on the wall mount.
Because of the tamper switch, the alarm rings out if the
control panel is separated from the wall mount.
- If you are using a SIM card, make sure the GSM reception of
the control panel is sucient before screwing the wall mount
onto the wall.
UP

7
Change the system language
The language of your system can be changed from the menu of
the control panel:
1. Type your Admin Code + on the control panel.
(Default Admin Code: 123456)
2. Go to System Settings > Language.
3. Select the language and conrm with .
A piece of advice
Type your Admin Code + to enter the menu and navigate
with , , ,(back), or (delete).
System Settings
Language

8
Activate or deactivate the GSM / Landline mode
Ignore this step if you are using the control panel with a SIM card
AND a landline connection.
Using a landline connection only
1. Type your Admin Code + on the control panel.
2. Go to System Settings > GSM Fail Tip. Select NO and press .
Using a SIM card only
1. Type your Admin Code + on the control panel.
2. Go to System Settings > Linecut Alarm. Select NO and press .
System Settings
GSM Fail Tip

Register a phone number
This step enables you to dene the phone number(s) on which
you receive a phone call when the alarm is triggered.
1. Type your Admin Code + on the control panel.
2. Go to Phone number > Phone 1 is and press .
3. Enter your phone number and conrm with .
If you register a phone number and an SMS number, you will be
notied by SMS and by phone call in case of alarm.
If you do not wish to use a SIM card, skip step 10 .
9
Phone 1 is:
057890033

Register a SMS number
This step enables you to dene the phone number(s) to which an
SMS is sent when the alarm is triggered. Only stored numbers can
control and congure the system by SMS and App.
1. Type your Admin Code + on the control panel.
2. Go to Phone number > SMS Num 1 is and press .
3. Enter your phone number and conrm with .
10
This step only applies if you are using your system with a SIM card.
SMS Num 1 is:
067890033

Now what happens if the alarm is triggered?
1. The siren of the control panel rings out.
2. You receive a phone call1. Pick up the call: you hear a voice
prompt giving you a list of options (stop the siren, disarm the
system, start audio surveillance etc.)
3. If there is a SIM card in your control panel, you also receive an
SMS notifying you that the alarm has been triggered.
A piece of advice
The memo at the end of this Quick Start Guide gives you the
most common commands you can send to your control panel
by SMS or phone call. Detach it and keep it with you at all
times.
1If you are using a landline connection and a SIM card, the call will be made
from the landline.
Your system is ready.
Advanced setup
For more settings, please refer to the user manual of
the control panel, available for download on
www.etiger.com/us/support

This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Manufactured in China.
Connect more sensors
1. Type your Admin Code + on the control panel.
2. Go to Wireless Sensors and press .
3. Select the type of zone and press .
4. Within the next 15 seconds, trigger the sensor.
5. You hear one beep: the accessory is registered.
Change the Access Codes
The User Code enables you to disarm your system from the
panel.
1. Type your Admin Code + on the control panel.
2. Go to System Settings > Access Code > User Code > .
3. Change the code and press (the code must consist of 4
digits).
The Admin Code can be changed using the same procedure
(under System Settings > Access Code > Admin Code).
Advanced settings

Memo
by phone call
Arm the system 1
Disarm the system
(stop the siren automatically) 0
Start audio surveillance
(stop the siren automatically) *
Start the conversation 3
Start the siren 9
Stop the siren 6
by SMS
Arm the system 1
Disarm the system 0
Home Mode 2
System status 00
To enable the control by phone call, please refer to
the full user manual on www.etiger.com
Memo
Detach it and keep it with you at all time
ETIGER USA, Inc.
1500 Fashion Island Blvd., Suite 102, San Mateo, CA 94404, USA
[e-mail]
A piece of advice Save time and use our Android and iOS apps to interact with your control panel (SIM card required).
S4-CL-QSG-EN20150602-1.3-W
Landline phone nb.
(SMS not supported)
SIM card’s phone nb.