eTIGER S3b Sim Secual Operator's manual

www.etiger.com
S3b Sim Secual / S3b Sim Vid Secual
GSM Alarm System
EN

Features
-GSM frequency: 850 / 900 / 1800 / 1900 MHz
- Supports up to 10 remote controls, 50 wireless accessories and 50 RFID tags
- Can store up to 5 phone numbers, 5 SMS numbers
-Radio-frequency security of the accessories: more than one million code combinations
- Arm / disarm the system by SMS, phone call, or App (on iOS or Android)
- Can be disarmed by RFID tag
- Built-in siren (100dB) and call function from the panel
- SMS alerts for power failure, power recovery and low battery
- Audio surveillance of the site from distance
-2 x 800 mAh lithium batteries included (8h battery life in standby mode)
Specications
Product name
S3b Sim Secual
SKU
S3b-S
Control panel power supply
Input: AC 110-240V / 50-60 Hz
Output: DC 12V / 800 mA
GSM operating frequency
850 / 900 / 1800 / 1900 mHz
Radio-frequency
433 MHz (±75 KHz)
Standby current
110 mA
Alarm current
340 mA
Backup batteries
Lithium batteries: 3.7 V / 800 mAh x 2 (BL-5B)
Internal siren
100 dB
Housing material
ABS plastic
Operating conditions
Temperature: -10°C~55°C
Humidity: ≤ 80% (non-condensing)
Control panel dimensions (L x W x H)
188 x 132 x 26 mm
Box Content
S3b Control Panel x1
Motion Detectors x2
Door / Window Contacts x2
Remote Controls x2
RFID Tags x2
AC Adaptor x1
Documentation x1
S3b Sim Vid Secual
+ IP Camera x 1 (with AC Adaptor and manual)

Quick Start-up

Accessories Safety and Troubleshooting
4
Quick start-up Control Panel Operations SMS Operations
Control Panel Layout (Front)
GSM Signal Indicator
Searching GSM network: Blinks once every second
GSM signal is normal: Blinks once every two seconds
Touch Keypad
Status Indicator
Record Voice Memo /
Connecon Buon
Stay Arm (Home Mode)
RFID player /
Play Voice Memo
Call
Arm
Disarm
Control Panel Layout (Back)
LoudspeakerMIC
Baery compartment
Tamper switch
SIM card Slot Power
On/O
Output for
wired sensors
Wired sensors
(24h zone)
Adapter interface
Electronic lock
Wired siren 500mA
Wired sensors
(Normal zone)

Accessories Safety and Troubleshooting
5
Quick start-up Control Panel Operations SMS Operations
Connect your System
Open the battery case at the back of the control panel and insert a SIM card in the control
panel.
Important
Before using the S3b Sim Secual, you need to purchase a SIM card that works on the GSM
network with 850 / 900 / 1800 / 1900 MHz frequency. We recommend you to subscribe to a
plan with unlimited texts and one hour of voice. For more information, please contact your
local reseller.
Important
Make sure the SIM card does not require any PIN code. For more information, please contact
your local reseller.
Turn your System On
1. Plug the AC adaptor to an AC socket.
2. Plug the output connector of the AC adaptor into the
adaptor interface in the battery compartment at the
back of the control panel.
3. Turn the power switch to "ON" (in the battery
compartment at the back of the control panel).
Mount the Control Panel
Before mounting the control panel on the wall, make sure the reception of the GSM signal is
sucient.
Fix the wall-mounting bracket on the wall with screws. Wedge the panel on the bracket, make
sure they t well.

Accessories Safety and Troubleshooting
6
Quick start-up Control Panel Operations SMS Operations
First Operations
Store a phone number
To interact with the control panel by SMS, by phone call and/or from the app, at least one phone
number for SMS notications must be stored in the control panel. Please refer to the instructions
page 13 of this manual.
Change the language
By default the language of the S3b control panel is set to English. If you wish to change the
system language, refer to the instructions page 18 of this manual. "System language" refers
to the language of the SMS you receive from the control panel.
Arm / Disarm the System
The alarm system can be armed or disarmed on the control panel, by SMS, by App and by phone
call.
On the control panel: Refer to the instructions on page 9 of this manual.
By SMS
To arm the system: Send “1”by SMS to the number of your system’s SIM card.
To disarm the system: Send “0”by SMS to the number of your system’s SIM card.
By RFID tag (disarm only): Swipe the RFID tag in front of the RFID reader of the control panel.
To start receiving SMS notications when the system is disarmed by RFID tag, you must store an
SMS number as explained on page 13 of this manual. If you have stored several SMS numbers,
only the rst number stored will receive SMS notications when the system is disarmed by RFID tag.
By app
In the app, click on“Arm”or“Disarm”to respectively arm or disarm the system.
The app is available for download on the App Store and Google Play (more information on etiger.com).
Register Wireless Accessories & RFID Tags
1. Type your password followed by the Connection button " " on the control panel to enter the
Connection Mode.
2. Trigger the accessory once within the next 15 seconds (for the RFID tag, swipe it in front of the
blue circle of the control panel). You hear one beep: the registration is successful.
Default password is 1234. To change the password, refer to instructions on page 18.
If the accessory has already been registered, the control panel will beep twice.The rst accessory
registered is assigned to zone 1, the second accessory registered is assigned to zone 2, etc. Zones
1 to 9 can be renamed. Zones 10 to 50 cannot be renamed (refer to the instructions on page 15
to learn how to rename zones).

Accessories Safety and Troubleshooting
7
Quick start-up Control Panel Operations SMS Operations
Speed Dial
This function is only available when the system is disarmed.
Press the Call button“ ”on the control panel for 3 seconds: the panel auto-dials the rst stored
phone number. Press the Call button“ ” to end the call.
Hands-Free Phone Call from the Panel
This function is only available when the system is disarmed.
Type the phone number you wish to call and press the Call button“”.
Record / Play a Voice Memo
Long press the RecordVoice Memo button { } to record a 10-second voice message.The PlayVoice
Memo Button blinks when a message has been recorded.
Touch the centrer of the circle on the control panel to listen to the voice memo. The LED in-
dicator turns o when the voice memo is being played. Touch it again to replay the memo.
Hard Reset
Turn the control panel on (if the control panel is already on, turn it o and turn it on again).
Press the tamper switch at the back of the control panel 5 times within 5 seconds after having
turned it on.
Settings will be restored to default values. Stored phone numbers and connected accessories
will be cleared.

Control Panel Operations

Accessories Safety and Troubleshooting
9
Quick start-up Control Panel Operations SMS Operations
Arm the System
Press the Arm button " " on the control panel. The control panel beeps once: the system is
armed.
Note
If the Entry / Exit Delay is activated, only the Delay zone will be armed after the delay set (refer
to instructions on page 17 of this manual “Entry / Exit Delay”).
Disarm the System
Type your password and press the Disarm button " " on the control panel. The control panel
beeps twice: the system is disarmed.
Home Mode
Press the Stay button " " on the control panel. The control panel beeps twice: the system is
armed in Home Mode.
In Home Mode, all the sensors are armed except those assigned to the Home zone. Sensors
assigned to the Home Mode zone are disarmed: they cannot trigger an alarm.
For more information on zone setup, please refer to the instructions on page 29 of this
manual.

Accessories Safety and Troubleshooting
10
Quick start-up Control Panel Operations SMS Operations
Control by Phone Call
Method 1
When an alarm has been triggered, the control panel dials the pre-stored phone numbers.
When you take the call, you can control the panel from distance according to the instructions
in the table below.
Method 2
1. Dial the telephone number of the SIM card in your control panel.
2. Enter your password followed by ”#”. *
3. Select the operations to control the panel (see instructions in the table below).
Note
The call will end automatically if you do not send any command within 30 seconds.
*Default password is 1234.
Table of commands for control by phone call
Command Function Comment
Press“1“ Arms the system -
Press“0“
- Disarms the system and turns the siren o
- Stops monitoring without hanging up
- Ends the phone call without hanging up
-
Press“ “Audio monitoring -
Press“3“ Phone call with control panel -
Press“6“ Turns the siren o -
Press“9“ Turns the siren on -
Press“#“ - Disarms the system and turns the siren o
- Exits control by phone call
Hanging up also exits the
control by phone call.

...
SMS Operations

SMS Operations
IMPORTANT: BEFORE USING FOR THE FIRST TIME
INSERT A SIM CARD IN THE CONTROL PANEL.
MAKE SURE THE SIM CARD DOES NOT REQUIRE ANY PIN CODE.
SAVE A PHONE NUMBER FOR SMS NOTIFICATIONS. Refer to instructions on the opposite page)
Only stored numbers can control and congure the system.
Each SMS operation dened in this user manual will be illustrated as follows.
You send:
6
The control panel replies:
SMS numbers:
1.
2.
3.
4.
5.
The rst blue speech bubble is the SMS
command sent by the user.
The rst grey speech bubble is the reply sent
by the control panel.
The speech bubbles that follow are the
dialogue between the user and the control
panel (SMS sent by the user are in blue, SMS
sent by the control panel are in grey).
The system is in English by default. To change the system language, refer to page 19
of this manual.
Important
When replying to the control panel by SMS, make sure no space follows punctuation marks
like "." or ":". For examples, to store SMS numbers, your SMS must be formatted as follows:
SMS numbers:
1.067890033
2.067890022
3.067890011
4.067890000
5.
No space after "1."
Accessories Safety and Troubleshooting
12
Quick start-up Control Panel Operations SMS Operations

Accessories Safety and Troubleshooting
13
Quick start-up Control Panel Operations SMS Operations
Store Phone Numbers for SMS
notications
Send:
6
SMS numbers:
1.
2.
3.
4.
5.
Copy, paste, then edit
(case sensitive):
SMS numbers:
1.067890033
2.067890022
3.067890011
4.067890000
5.
Ok
Note
The rst SMS number will receive SMS
notications when the system is disarmed
by RFID tag.

Accessories Safety and Troubleshooting
14
Quick start-up Control Panel Operations SMS Operations
Disarm the System
Send:
0
System disarmed.
Arm the System
Send:
1
System armed.
Home Mode
Send:
2
System in home mode.
Settings Enquiry
Send:
00
System:Disarmed
AC power:on
Note
The values indicated hereinabove will
change after having set up the system.

Accessories Safety and Troubleshooting
15
Quick start-up Control Panel Operations SMS Operations
Store Phone Numbers
Send:
5
Phone numbers:
1.
2.
3.
4.
5.
Copy, paste, then edit
(case sensitive):
Phone numbers:
1.067890033
2.067890022
3.067890011
4.067890000
5.
Ok
Rename Zones
Send "91~99". For example for zone 1, send:
91
Zones names:
1.
Copy, paste, then edit
(case sensitive):
Zones names:
1.Entrance door sensor
Ok
Note
Zones 1 to 9 can be renamed. The name of
the zone cannot consist of more than 30
Latin characters. Zones 10 to 50 cannot be
renamed.

Accessories Safety and Troubleshooting
16
Quick start-up Control Panel Operations SMS Operations
SMS Alert for Accessory Low Battery
(available for two-way acessories such as
Motion Detectors)
For accessories assigned to zones that have
been renamed, an SMS will be sent under the
format“Zone number +zone name + Low BAT”.
Zone 10 Bedroom PIR Low BAT
For accessories assigned to zones that have
not been renamed, an SMS will be sent
under the format“Zone number + Low BAT”.
Zone 10 Low BAT
SMS Alert for Accessory Tamper
Alarm
(available for two-way acessories such as
Motion Detectors)
For accessories assigned to zones that have
been renamed, an SMS will be sent under the
format“Zone number +zone name +Tamper”.
Zone 10 Bedroom PIR Tamper
For accessories assigned to zones that have
not been renamed, an SMS will be sent
under the format“Zone number + Tamper”.
Zone 10 Tamper
Rename RFID Tag
Send:
10
Rename RFID tags:
1.
2.
3.
4.
Copy, paste, then edit
(case sensitive):
Rename RFID tags:
1.Tom
2.Nurse
3.Nancy
4.David
Ok
Note
The rst SMS number will receive SMS
notications when the system is disarmed
by RFID tag.
If the RFID tag that disarms the system has
been renamed, the SMS notication will
be "Tag 01 Tag name Disarm". ("01" is the
number of the tag)
Other tags will be attributed a number
based on the order of registration to the
control panel; the SMS notications will in
such case be "Tag-04 Disarm" ("04" is the
number of the tag). Refer to the instructions
on page 28 to learn how to register an
RFID tag in the control panel.

Accessories Safety and Troubleshooting
17
Quick start-up Control Panel Operations SMS Operations
Entry and Exit Delay Time
Send:
11
Entry delay time(0-300sec):0
Exit delay time(0-300sec):0
Copy, paste, then edit
(case sensitive):
Entry delay time(0-300sec):10
Exit delay time(0-300sec):20
Ok
Note
This function will only aect detectors
assigned to the Delay zone. Refer to the
instructions on page 29 of this manual to
learn how to set up your sensor to the Delay
zone.
This function can be used if you do not want to
bring a remote control or a RFID tag with you.
When you arm the system, the system
will be armed after the delay set. When
you disarm the system, the system will be
disarmed after the delay set.
When arming the system, you hear one
beep every second to remind you to leave.
The beep rhythm speeds up during the last
10 seconds. If an intruder is detected, the
alarm will be delayed accordingly.
Siren Volume and Ringing Time
Send:
12
Siren volume(0=Mute,1=High):1
Siren ringing time(1-9min):3
Copy, paste, then edit
(case sensitive):
Siren volume(0=Mute,1=High):0
Siren ringing time(1-9min):1
Ok

Accessories Safety and Troubleshooting
18
Quick start-up Control Panel Operations SMS Operations
Change the Password
Send:
13
Disarm password (4 digits):
1234
Copy, paste, then edit
(case sensitive):
Disarm password (4 digits):
8888
Ok
Change System Language
Send the code corresponding to the
language you want to set. For example, for
English, send“0001”.
0001
Ok
Refer to the table below for the full list of
language codes:
0001 English
0002 French
0003 Russian
0004 Danish
0005 Dutch
0006 Italian
0007 Swedish
0008 German
0009 Spanish
0010 Finnish
0011 Norwegian
0012 Arabic
0013 Farsi
Languages available may vary depending
on the version of your product.

Accessories Safety and Troubleshooting
19
Quick start-up Control Panel Operations SMS Operations
Restore System to Factory
Settings by SMS
Send:
0000
Ok
The settings will be restored to default
values. Stored phone numbers and
connected accessories will also be deleted.
Note
Only stored numbers can send the SMS to
restore factory settings.

Accessories