EURO EP900UMS User manual

EP900UMS

1
CONTENT
2……………………………………….Notice
3………………………………………..Installation
3…………………………………………Use
4………………………………………..Notice of installation
4………………………………………..Safety Warning
5…………………………………………Maintenance
7…………………………………………Abnormity and Solution

2
NOTICE
1. Thank you for choosing our cooker hood. Please read the
instruction manual carefully before use.
2. The installation work must be undertaken by a qualified and
competent fitter.
3. The manufacturer disclaims all liability for any damage or
injury caused as a result of not following instructions for
installation contained in the following text.
The cooker hood is used on 220/240v, 50Hz.
Contents
1X Rangehood
1X Packet of Screws
1 X Operating Instructions

3
(1) INSTALLATION
1. The cooker hood should be placed at a distance of 65-
75cm (26-30inch) from the cooking surface for the best
effect.
2. Drill a hole in the cupboard, with hole wide 490*265
(mm). Make sure it’s at least 35mm from the edge of the
hole to the cupboard edge.
3. Take down the filter and remove the 2 (M4 x 10mm)screws on the
panel.
4. Use random accessory tighten 8 screws (ST4 x 18mm) fix the hood
into cabinet.
5. Use 2 screws(M4 x 10mm) fix the panel into body and equip the filter.
6. Install one-way valve: put the one-way valve into air outlet,
Put on the one-way valve with air outlet.
（2）USE
1. Push stop button, and the motor will stop.
2. Push the Low button, the motor runs at low speed.
3. Push the Mid button, the motor runs at mid speed.
4. Push the High button, the motor runs at high speed.
5. Push the light button and the two lights will come on. Push it
again and the light will turn off.

4
Explain the instructions:
a. Connection of the appliance to the supply mains.
b. Necessity to allow disconnection of the appliance from the supply
after installation. Disconnection may be achieved by having the
plug accessible or by incorporating a switch in the fixed wiring in
accordance with the wiring rules.
Warning: Failure to install the screws or fixing device in accordance
with these instructions may result in electrical hazards.
(3) NOTICE OF INSTALLATION
1. Before installation, please ensure the area is clean to avoid suction of
the remaining bits of broken wood and dust.
2. The air must not be discharged into a flue that is used for exhausting
fumes from appliances burning gas or other fuels.
3. The bending of ventilation tube should be≥120°, parallel or above
the start point and should be connected to the external wall.
4. After installation, make sure that the extractor is level to avoid grease
collection at one end.
Installation warnings
a. There shall be adequate ventilation of the room when the range hood
is used at the same time as appliances burning gas or other fuels.
b. Regulations concerning the discharge of air have to be fulfilled.
(4) SAFETY WARNING
1. Never let the children operate the machine
2. The cooker hood is for home use only, not suitable for barbecue,
Roast shop and other commercial purpose.
3. Please ask the technical person to do the assembling.
4. The cooker hood and its filter mesh should be clean regularly in order
to keep in good working order.
5. Before cleaning, please switch the power off at the main supply.
6. Clean the cooker hood according to the instruction manual and keep
the cooker hood from the danger of burning.
7. If there is any fault with the appliance, please call the service
department to arrange a service engineer.
8. There is a fire risk if cleaning is not carried out in accordance
with the instructions.
9. Do not flambé under the range hood.

5
CAUTION:
Accessible parts may become hot when used with cooking
appliances.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
(5) MAINTENANCE
1. The cooker hood and its filter mesh should be cleaned regularly in
order to keep in good working order. Because the grease filters are
made of metal, do not clean the filters with detergents that will
corrode metal products.
2. Clean the filters as below:
a) Method one:
Put the filter in the water(40℃-50℃), pour in some grease-
loosening detergent, soak it for about 2-3 minutes and then clean it
with a soft brush. Do not brush too hard, in case to damage the
filter.
b) Method tow:
User can put the filter into a dishwasher with detergent for cleaning.
Set the temperature at around 60℃.
3. To protect the main body from corrosion over a long period of time,
the cooker hood should be cleaned with hot water plus soap or non
corrosive detergent once a week. Do not use grinding detergent, or it
will damage the body.
4. Keep the motor and other spare parts free from water, as this will
cause damage to the appliance.
5. Disassembly and assembly the filter:

6
6. Activated carbon filter can be used to trap odors. In order to install
the activated carbon filter, user have to unscrew and take down the
front panel. Then plug the activated carbon filter into the unit and
turn it in anti-clockwise direction. Repeat the same on the other side.
NOTE:
Make sure the filter is securely locked. Otherwise, it could loosen
and cause damage to the unit.When activated carbon filter attached,
the suction power will be lowered.
7. To change the bulb, press the lamp cup, take out the bulb in the
counter-clockwise.

7
(6) ABNORMITY AND SOLUTION
Fault Cause Solution
Light does not work,
but motor work
The bulb damaged Change bulb
Bulb contact lamp cap bad Fix or change
Light panel switch damage Fix or change
Light work, but
motor does not work
Bulb contact lamp cap Restart later
Motor bearings damage Change motor
Motor burn out Change motor
Motor control switch damage Fix or change
Light does not work,
motor does not work
Plug contact outlet bad Fix or change
Power wire cut off Change power wire
Switch damage Fix or change
Shake of the body
Wind leaves damage Change leaves
Motor screw loosen Screw it tight
Combination screw loosen Screw it tight
Body hang unfixable Tight the body
Insufficient suction
The distance between the body
and the gas top too long Readjust the distance
Cross-ventilation too strong or
too closed in the kitchen
Reduce cross-
ventilation or open the
window
Exhaust pipe too long Adjust the length of
pipe
Air outlet valve not open Check the valve if
flexible
The outside wind is too strong No the technical
problem