EURO EP900ISS User manual

- 1 -
Range hood
Instruction Manual
EP900ISS
EURO APPLIANCES BY EUROSTYLE GROUP

- 2 -
CONTENT
1……………………………………….Notice
2……………………………………….Feature
3………………………………………..Installation
4………………………………………..Notice of installation
5………………………………………..Safety Warning
6…………………………………………Use
7…………………………………………Maintenance
8…………………………………………Abnormity and Solution
9…………………………………………Warranty card

- 3 -
NOTICE
1. Thank you for choosing our cooker hood. Please read the
instruction manual carefully before use.
2. The installation work must be undertaken by a qualified and
competent fitter.
3. The manufacturer disclaims all liability for any damage or
injury caused as a result of not following instructions for
installation contained in the following text.

- 4 -
(2)FEATURE
1. The cooker hood uses high quality materials, and is made with a
streamlined design.
2. Equipped with a large power low noise electric motor and
centrifugal leaf, it produces strong suction, low noise, non stick
grease filter and easy to clean.
3. With the isolated low voltage circuit board control, 12vAC
input, the lights are therefore safer.
4. Special wind tunnel construction and oil collector design, free
dirt will be absorbed in a second.

- 5 -
(3). Installation
1. The ceiling must can bear at least 40kgs weight, and the
thickness of the ceiling must be ≧30MM, see pic 2, drill
1*170mm round hole in the ceiling.
2. According to the hanging board, drill 12 holes in the ceiling, see
pic 2, 12pcs of ST6*40mm big flat screws will be used to fix the
hanging board on the ceiling, and then 8pcs of M4*10 screws
and M4 nut with gasket will be used to connect the angle iron
into the hanging board, see pic 1, calculated the length of the
angle iron, and 16pcs M4*10 big flat screws and M4 nut with
gasket will be used to connect the angle iron and another angle
iron ( the overlap length of angle iron can not less 100MM)
3. Let the one side of the extensible pipe go outside through the
hole of 170MM, see pic 3.
4. 4pcs ST4*8 big flat screws will be used to connect the internal
chimney into the hanging board, then put one the external
chimney, two hooks will be used to put up the external chimney
in order to the next installation, see pic 4.
5. 4pcs ST4*8 big flat screws will be used to install the outlet, see
pic 5.
6. Hold up the hood, 16pcs M4*10 big flat screws will be used to
connect the hood body into angle iron, see pic 6.
7. Put the extensible pipe on the outlet; after ensure all the things
ok, put down the hook, take from the external chimney, all the
installation is finished, see pic7& 8.

- 6 -

- 7 -
(4) NOTICE OF INSTALLATION
1. Before installation, please ensure the area is clean to avoid
suction of the remaining bits of broken wood and dust.
2. It cannot share the same air ventilation tube with other
appliance such as gas tube, warmer tube, and hot wind tube.
3. The bending of ventilation tube should be≤120°, parallel or
above the start point and should be connected to the external
wall.
4. After installation, make sure that the extractor is level to avoid
grease collection at one end.
(5) SAFETY WARNING
•
••
•Never let the children operate the machine
•
••
•The cooker hood is for home use only, not suitable for
barbecue, Roast shop and other commercial purpose.
•
••
•Please ask the technical person to do the assembling.
•
••
•The cooker hood and its filter mesh should be clean regularly
in order to keep in good working order.

- 8 -
•
••
•Before cleaning, please switch the power off at the main
supply.
•
••
•Clean the cooker hood according to the instruction manual and
keep the cooker hood from the danger of burning.
•
••
•If there is any fault with the appliance, please call the service
department to arrange a service engineer.
（
（（
（6）
））
）Speed adjustment .See pictures
1. Turn on the power; the buzzer will buzz five times. The sound
shows that the appliance is powered.
2. Push the low button, the indicating light 1 on, the buzzer will
buzz once, and the motor runs at low speed. Push it again and
the motor will stop.
3. Push the middle button, the indicating light 2 on, the buzzer
will buzz once, and the motor runs at mid speed. Push it again
and the motor will stop
4. Push the high button, the indicating light 3 on, the buzzer will
buzz once, and motor runs on high speed. Push it again and the
motor will stop
5. Push the light button; the indicating light 4 on, and the two
lighting lamps will come on. Push it again and the lamps will
turn off, with every push the buzzer will buzz one time.

- 9 -
(7) MAINTENANCE
7.1 The cleaning of the carbon grease filter mesh
The filter mesh is made of high-density stainless steel. Please do not
use the corrosive detergent on it. Keeping this filter clean will keep
the appliance running correctly. Please strictly follow the guidelines
below.
Method 1: Put the mesh into 40-50 c clean water, pour on detergent,
and soak for 2-3 mins. Wear gloves and clean with a soft brush.
Please do not apply too much pressure, as the mesh is delicate and
will damage easy.
Method 2: If instructed to do so, it can be put into a dishwasher, set
the temperature at around 60 degrees.
7.2 Notice of cleaning cooker hood
A. To protect the main body from corrosion over a long period of
time, the cooker hood should be cleaned with hot water plus
non corrosive detergent every two months.
B. Please do not use abrasive detergent for it will damage the
body.
C. Keep the motor and other spare parts free from water, as this
will cause damage to the appliance.
D. Before cleaning the appliance please remember to cut off
power
E. The carbon filter shouldn’t be exposed to heat.
F. Please don’t tear open the fixed bar around the carbon filter
G. If the plug or cord is damaged, please replace it with special
soft cord.

- 10 -
8. Abnormity and Solution
Fault
Cause Solution
Light on, but motor
does not work
The leaf blocked Get rid of the blocking
The capacitor damaged Replace capacitor
The motor jammed bearing
damaged
Replace motor
The internal with of motor off or
a bad smell from the motor
Replace motor
Light does not work,
motor does not work
Beside the above mentioned, check the following:
Light damaged Replace lights
Power cord looses Connect the wires as per
the electric diagram
Oil leakage
One way valve and the air
ventilation entrance are not
tightly sealed
Take down the one way
valve and seal with glue
Leakage from the connection
of U-shaped section and
cover
Take U-shaped section
down and seal with soap
or paint
Shake of the body The leaf damaged and causes
shaking
Replace the leaf
The motor is not tightly
hanged
Lock the motor tightly
The body is not tightly
hanged
Fixed the body tightly

- 11 -
Insufficient suction The distance between the
body and the gas top too long
Readjust the distance
Too much ventilation from
open doors or windows
Choose a new place and
resemble the machine
The machine inclines The fixing screw not tight
enough
Tighten the hanging
screw and make it
horizontal
The hanging screw not tight
enough
Tighten the hanging
screw and make it
horizontal

- 12 -
Eurostyle Group trading as Euro Appliances
Service Line: [phone]
Fax: [phone]
Email: [email protected].au