Eurotech ReliaGATE 50-21 User manual

ReliaGATE 50-21 Development Kit
Quick Start
110126-9000B November-2012
What’s in the Development Kit?
The development kit includes the following components:
•ReliaGATE multi-service gateway with
oWind River Linux 4.3 operating system
oEveryware™ Software Framework (ESF) and
Denali routing application
oGPS
oWi-Fi (IEEE 802.11)
oCellular (GSM/GPRS or CDMA)
oIEEE 802.15.4/Zigbee®Standard
oFour USB 2.0 host ports
oTwo Gigabit Ethernet ports
oTwo EIA-232/485 port (5-wire)
oTwo CAN2.0 busses
oVGA display output
oLED status indicators
oGeneral-purpose inputs and outputs
(with 12-position terminal block mating connector)
•3-in-1 antenna for GPS, Wi-Fi, and cellular
(Contact Eurotech for use of Zigbee feature.)
•Null modem serial cable
•Ethernet crossover cable
•12 VDC power adapter and AC power cord
(with 2-position terminal block mating connector)
•Mounting option (bumpers and screws) for use when
brackets are not installed.
What Do I Need to Provide?
•Internet access for ReliaGATE (Ethernet – DHCP)
•Development PC with Internet access
•VGA display and USB keyboard
What are the Cellular Options?
ReliaGATE offers a GSM/GPRS or CDMA option for
cellular network connectivity. Contact your Eurotech sales
representative for part numbers.
•To install your activated SIM card for GSM/GPRS,
remove the SIM access panel.
•CDMA versions support activation on Sprint or
Verizon networks.
How Do I Set Up the Development Kit?
Hardware Connections
To prepare your ReliaGATE, complete the following steps:
1. Connect the 3-in-1 antenna provided with your kit as
follows:
oCable labeled 2.4-2.5 / 4.9-6 GHz to Wi-Fi
oCable labeled 2.1-2.5 /4.4-6 GHz to Div
oCable labeled 800-1250 / 1650-2700 MHz to Cell
oCable labeled 3V/5V GPS to GPS
2. Connect a VGA display and USB keyboard.
3. Connect the lower Ethernet port to an Ethernet
network with Internet access.
4. Connect the 12 VDC power adapter to the DC power
input, and then connect the adapter to AC power. The
Power LED lights green when power is successfully
connected.
5. The system will boot the Linux operating system to
the GRUB menu displayed on the graphics console.
6. Press Enter to select the graphics console.
7. After the message startall –force is displayed,
press Enter for the login prompt.
Power LED
Cell Activity LED
User-configurable
LEDs (2)
SIM Access Panel

110126-9000B November-2012
Administrative Login
•You can log into the administrative console from the
graphics console (VGA display/USB keyboard) or
serial console (Serial 1 at 115200, N81), by choosing
an option from the GRUB menu.
•Remote log in via Secure SHell (SSH) is available.
•Username is root and password is IsiTech.
•Shut down the system before disconnecting power.
To shut down, use poweroff.The Power LED will
turn off when the system has successfully shut down.
Feature Configuration
Your ReliaGATE runs the Denali routing application
software which can configure the following networks:
•Ethernet via fixed IP address or DHCP (default)
•Wi-Fi (IEEE 802.11) via fixed IP address or DHCP
•Cellular via the modem option installed
•GPS
To change the configuration, complete the following steps:
1. In the administrative console, type ifconfig eth0.
2. HTTPS is used for secure transfer of configuration
data. On your PC, open a Web browser and enter
https://ip_address where ip_adress is the inet address
displayed in step 1.
3. Your browser may display a warning about the
certificate. Select the option in your specific browser
to continue past the security warning.
4. In the dialog box, enter the User Name eurotech
and Password eurotech.
5. The Denali Setup Web page is displayed.In the
appropriate tab, make any necessary configuration
changes and submit the new configuration. Changes
to the network settings take effect immediately. It is
not necessary to reboot.
How Do I Connect to the Everyware
Cloud?
ReliaGATE leverages ESF, plus the power of Denali, to
provide a complete, cloud-ready development platform.To
connect to the Everyware Cloud, you must
•Request an account by contacting your Eurotech
sales manager or email [e-mail].
•Configure Denali on your ReliaGATE with your
account credentials (URL, username, and password).
What are the Hardware Features?
USB Host Ports
The four USB 2.0 ports are general-purpose USB host
ports (500 mA max).
Gigabit Ethernet Ports
In Linux, the lower Ethernet port is assigned to eth0, while
the upper port is assigned to eth1.Note that the upper
Ethernet port is implemented by a high-speed USB 2.0 to
10/100/1000 Ethernet Controller.
Serial Ports
By default, Serial 1 and Serial 2 are 5-wire, EIA-232.
These ports can be configured for EIA-485 mode by
changing the settings in the BIOS Setup utility.
CAN
The pin assignment on the CAN connector is:
Pin
Type
Description
1
IO
CAN 2-
2
IO
CAN 1-
7
IO
CAN 1+
8
IO
CAN 2+
Note: Other pins are not connected.
General-Purpose Inputs and Outputs
The 12-position terminal block provides analog inputs
(A1-A2), isolated digital inputs (D1-D4), isolated digital
outputs (DO1-DO2), and a sleep/wake input (IGN).
Where Do I Find User Documentation?
See the following documents for additional details:
•ReliaGATE User Manual at
http://support.eurotech-
inc.com/forums/topic.asp?topic_id=3057
•Denali User Manual at
http://support.eurotech-
inc.com/forums/topic.asp?topic_id=3040
•Everyware Cloud Developer’s Guide at
http://everywarecloud.eurotech.com/doc/ECDevGuide
•Everyware Software Framework Developer’s Guide at
http://esf.eurotech.com/doc/ESFDevGuide
Eurotech Technical Support
The Eurotech support site includes errata reports, the
latest versions of user documents, and developer’s forums.
These resources are available to registered developers at:
http://support.eurotech-inc.com/
Contact Us
EUROTECH
Toll-free +1 888.941.2224
Tel. [phone]
Fax [phone]
E-mail: [e-mail]
E-mail: [e-mail]
Web: www.eurotech-inc.com