Eusso UTG7100-IP Series User manual

UTG7100-IP Series
SIP VoIP Telephone
User Manual
V1.1t
1

2
Table of Content
1. Introductions ................................................................3
2. Features ......................................................................3
3. Standard Compliances ................................................4
4. Packing Contents ........................................................4
5. LED Indicators .............................................................4
6. Installations & SIP Configurations ...............................5
7. Default Reset by Using Keypads.................................5
8. Configurations by Web Browser ..................................6
9. LCD Display with Keypads Settings ..........................39
10. VoIP Application Examples......................................43
11. Trouble Shooting for Web Configurations................47

3
1. Introductions
The UTG7100-IP is an IP Telephone with SIP Protocols for Voice over IP (VoIP) applications.
Connecting to the Internet, the UTG7100-IP can make a VoIP call over the Internet. The UTG7100-IP
provides one WAN port for Internet ADSL connections, and one LAN port for Notebook PC. With an
embedded NAT/DHCP server, UTG7100-IP can be easily configured for different network diagrams
by IE Web browser and telephone keypads. UTG7100-IPE is the same as UTG7100-IP with additional
Power over Ethernet feature. With power supply over Ethernet cable from central Ethernet Switch,
UTG7100-IP may work without external power adapter. It is very convenient for ITSP (Internet
Telephony Service Providers) and SOHO users to make VoIP calls with registrations to IP PBX.
Note that UTG7100-IP requires an IP address, a subnet mask, and its gateway Router IP address for
its own use to connect to Internet. These three are available from your Internet service provider.
UTG7100-IP may enable PPPoE or DHCP features to automatically get an assigned dynamic IP from
the ITSP. Please refer to Section 8 Configurations by Web Browser for detailed information.
2. Features
Equipped with two RJ45 connectors UTG7100-IP is featuring as the following
¾Two LED Indicators: REG for registration, VMS for voice mail
¾RJ45 x 2 for WAN and LAN ports
¾Support Power over Ethernet feature (for UTG7100-IPE only)
¾Configurations by Web Browser and Telephone Keypads
¾Embedded NAT/DHCP Server
¾PPPoE/DHCP Client for Dynamic IP plus NAT, DNS, and DDNS Clients
¾Support STUN server for NAT Traversal
¾Support registrations for up to 3 SIP Servers.
¾Hot Line Mode
¾Dial Plan Settings
¾Speaker Phone, Voice Message (VMS) for incoming IP calls
¾Call Forward/Transfer/Waiting/Hold, and 3-Way Conference Call features
¾Auto Configurations by TFTP, HTTP, or FTP server
¾Remote Firmware Upgraded with HTTP or TFTP server by Web PC
¾Direct IP/URL Dial without SIP Proxy or Dial number via SIP server
¾Telephone features: Volume Adjustment, Phone book, Redial
¾Function Keys: Speed Dial, 3 SIP Registration Lines, DND, VMS, and Pickup
¾Out-Band DTMF (RFC 2833) / In-Band DTMF / Send DTMF SIP Info

4
3. Standard Compliances
The UTG7100-IP VoIP Phone supports for the following standards
VoIP Protocol: IETF RFC3261 and RFC 2543 for SIP
SIP Authentication: IETF RFC2069 and RFC 2617 for MD5
Speech Codec: ITU-T G.711, G.723, G.729A/B, VAD and CNG
Echo Cancellation: ITU-T G.165/168
4. Packing Contents
Inside the package you should find:
(1) One UTG7100-IP SIP Phone
(2) One AC to DC Power Adaptor (9~12VDC/1A)
(3) One User Manual CD
Please check if the packing is damaged or any component is missing. If so, please contact your
distributor.
5. LED Indicators
On the front panel of UTG7100-IP , there are three LED indicators as the following
REG: “Green On” indicates successful registration at SIP server.
VMS: “Red Flashing” indicates there are voice messages for incoming VoIP call.
To hear the message you may press the Speaker Phone key then VMS function key.

5
6. Installations & SIP Configurations
1. Connect UTG7100-IP RJ45 WAN port to NAT Router using a Category 5 LAN cable.
2. Connect RJ45 LAN port to Notebook PC using a Category 5 LAN cable.
3. Connect DC Power Adaptor. The LCD Panel will start displaying ”Loading Program”for about 5
seconds, and the LEDs will be ON and start initializations.
4. . The LCD panel will show Date, Time and No service without SIP registration, or <phone number>
after successful SIP registration.
5. Pick up the phone, and you will hear a dial tone and the LCD panel will show IP Dialing.. 1.If you
hear a busy tone, please check if the WAN port is connected and hang up.
6. Press Menu_7_4, and test (i.e. press 8two times_3three times_7five times_8two times_enter) to
enter password first. Press Menu_4_5 from keypad to read WAN and LAN IP addresses. The
default LAN IP address is 192.168.123.1.
7. Go to Chapter 8 and you may enter this IP address in IE Web browser for web configurations.
Configure and register UTG7100-IP into your SIP server. There are more details and examples
for VoIP application of SIP registrations in Chapter 10.
8. If UTG7100-IP has successfully registered in the SIP server, the LED REG will turn ON.
9. Pick up the phone, and press 123456# to call the party with the number 123456 registered in the
SIP server. Note that #will dial out the number immediately. Dialing without # will not dial out until
the auto dial timer (default=5 seconds) elapsed. In a moment, you should hear a ring back tone,
and wait for answer.
7. Default Reset by Using Keypads
Press Menu / 7.Administrator / 3.Default setting / 1.Load default by using Menu and arrow keys to
reset back to factory defaults, and the LCD panel will show Set Default…. In 5 seconds, the LCD will
start showing Loading Program and System Initialized. The UTG7100-IP will reset to default and
restart.
Press Menu / 7.Administrator / 7.Restart to reboot UTG7100-IP . In 5 seconds, the LCD will start
showing Loading Program and System Initialized.

8. Configurations by Web Browser
You may enter the IP address from PC Web browser to configure UTG7100-IP . For example, enter
http://192.168.123.1:9999 from IE web browser to display login page as follows.
8.1. Please enter the default IP address http://192.168.123.1:9999 from PC Web browser.
The following Web page shall be displayed on PC. If you have difficulties accessing the Web page
from the PC Web browser, the subnet IP of PC might be different from 192.168.123.xxx.In this
case, please refer to Chapter 9 for trouble shooting.
8.2. Please enter the username and password into the blank field. The default settings are:
Username: root
Password: test
8.3. Click the “Login” button to enter the System information page for web configurations.
Whenever you change the setting in each Web page, remember to click the “Submit” button in the
page, and click the “Save” button to save into the non-volatile memory and click the “Reboot” button
to activate the new settings.
6

System Information
8.4. The system information shows firmware version, Codec, etc.
8.5. You may click the buttons, for example Phone Book, at the left hand side to configure the
UTG7100-IP .
Phone Book
Phone Book Settings
8.6. You may add/delete Name up to maximum 140 entries in Phone book list.
8.7. To add a phone name, you need to enter the position, the name, and the phone URL. When you
finished a new phone list, just click the “Add Phone” button.
8.8. To delete a phone name, please select the phone name then click “Delete Selected” button.
8.9. To delete all phone names, please click “Delete All” button.
8.10. After dialing a phone number, the UTG7100-IP will first match with the Name in the phone book.
If matched, UTG7100-IP will send out the corresponding URL instead. If not, the same dialed
number will be sent out.
Example 1: Name: 333, URL: 192.168.1.100
Press 333# on telephone, and the phone at 192.168.1.100 will start ringing.
Example 2: Name: 201, URL: 14081234567
Press 201# on telephone, and UTG7100-IP will call the registered number
14081234567.
Example 3: Name: 301, URL: 192.168.1.100:5062
Press 301# on telephone, and UTG7100-IP will call at 192.168.1.100 with port 5062.
Example 4: No Name 401 in phone book.
Press 401# on telephone, and UTG7100-IP will call the registered number 401.
7

8

Speed Dial Phone List
8.11. You can add/delete Speed Dial number up to maximum 10 entries in Speed Dial Phone List.
8.12. If you need to add a phone number into the Speed Dial list, you need to enter the position, the name,
and the URL. Click the “Add Phone” button to finish the setting.
8.13. To delete a phone number, please select the phone number you want to delete then click “Delete
Selected” button. If you want to delete all phone numbers, please click “Delete All” button.
Example 1: Press 2# from keypad to Speed Dial the phone number 2immediately.
Example 2: Press M2 function key will Speed Dial the phone number 2immediately.
9

Phone Setting
Call Forward Setting
8.14. You can select the forward mode and enter the forward URL.
All Forward: All incoming call will forward to the URL you choose.
Busy Forward: The incoming call will forward to the URL when you are busy and on the phone.
No Answer Forward: The incoming call will forward to the URL when no answer.
8.15. You need to set the Time Out ring which will initiate No-Answer forwarding to the number you
choose. When you finished the setting, please click the “Submit” button.
10