EVA Logik WF96SD User manual

Specifications
Plug x 1
Screw x 1
Plastic Anchor x 1
Meet your new smart Plug !
IMPORTANT!
This unit is suitable for outdoor use in damp locations.
Do not expose to rain or immerse in water.
Note:
Your device needs to be installed in the network coverage of your home router.
NOTE: Do not plug an extension cord in this smart plug.
Power: 120VAC, 60Hz
Item Size: 56*80*39mm
Loading : 400W
Wireless Frequency: 2.4GHz
Wireless Standard: IEEE802.11b/g/n
Operating Temperature: -4° F~122° F
Introduction
The EVA LOGIK WF96SD is a 400W MAX Loading smart dimmer plug
designed for use seasonal and landscape lighting, porch light, and
other indoor and outdoor plug-in small appliances. It's compatible
with dimmable LED, halogen, incandescent, and fluorescent bulbs.
Works with Amazon Alexa, Google Assistant. You can use the free
App--Smart Life, or voice control by Alexa and Google Assistant to
operate your devices in your home.
• WF96SD •
RGB LED indicator
For outdoor use
IP65 Rated
1. Please scan the QR code to download the application “Smart Life”.
2. If you cannot download Smart Life app, please search “Smart Life”
on Google Play (for Android phone) or Apple Store (for iOS phone) to
download.
3. The smart switch can be also used with Amazon Echo and Google
Home. Please scan the QR code below and follow the instructions if
you have any trouble pairing with them.
QR code Smart Life
,
please follow the instructions below to set up your smart switch.
(A) Manual / Program button
This is your smart outlet that will be
included in your smart home.
(B) Dimmer Outlet
Insert in connector when not in use.
(C) Protector
Single press: manually turn on/off
your device.
Hold: adjust brightness.
A
B
C
The plug is designed to
be angled 45 degrees,
allowing you to make
the most of your home
wall outlet.
Use our screws
and anchor to
lock it in the
wall.(optional)
Sky-blue: Network configuration mode
Blue: Light status indicator
Red: Network Failure/Overloading Warning
P
urple: AP Network configuration mode
Overloading protection is protection against overheat-
ing of the protected equipment. When the device's
temperature is high, the LED will light up in red and cut
down the power. Please power off the device and use it
When the LED is purple (AP mode), please press the
button 3 times quickly until the LED change to
Sky-blue
and LED blinks--Back to EASY MODE.
APP Connection
Amazon-Echo Google-Home
Wi-Fi
Outdoor Dimmer Plug

OTHER WARNINGS
Risk of Fire
Risk of Electrical Shock
Risk of Burns
CAUTION - PLEASE READ!
This device is intended for installation in accordance with the National Electric
Code and local regulations in the United States, or the Canadian Electrical Code
and local regulations in Canada. If you are unsure or uncomfortable about
performing this installation consult a qualified electrician.
MEDICAL EQUIPMENT
Please DO NOT use this plug to control Medical or Life Support equipment. This
device should never be used to control the On/Off status of Medical and/or Life
Support equipment.
FCC warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must acceptany interference received, including interference that
may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.
8
7
6
5
Tap ‘+’ to add a
device in your app
1 2 3Press the button 3 times
quickly until
“sky-blue”
LED blinks rapidly.
4
Enter the Wi-Fi
Password
Select “Electrician ”-
“Soclet (Wi-Fi)”
Click to “Continue ”
Select “is fast blinking(0.5s/time)”
▶ Easy Mode ◀
Wait for it’s 100%
(LED stays in green 3 seconds.)
100%
Mini Outdoor Dimmer P...
Adjust the brightness of the light.
SETTING
For better performance of
the LED, please set a
maximum /minimum-
brightness value. When the
bulb is at this maximum
/minimum brightness
value, the bulb does not
flicker. The minimum
brightness of different
bulbs may be different.
Locks for the minimum/
maximum value
• Restores State aer Power Failure (This parameter can access you to set the
plug to be on/off aer power failure.)
Value=0 The plug is OFF regardless of the state prior to power failure.
Value=1 The plug is ON regardless of the state prior to power failure
Value=2 (default) Memory state before power failure This switch will be return to
state prior to the power failure aer power is restored.
Operation: Quickly press button 8 times.
Please note: the switching of each value is in order, a quick press button 8 times
will switch once. eg: Switching from value 0 to value 2 needs 2 switchings.
• Light off State Setting (This parameter can access you to set the light fade
out or off immeditaly.)
Value=1 (default) Fade out
Value=2 Instantaneous off
Operation: Quickly press button 10 times
Please note: the switching of each value is in order, a quick press button 10 times
will switch once. eg: Switching from value1 to value 2 needs 1 switching.