EVA Logik ZW36 User manual

ZW36
Z-Wave Smart Plug
(1 channel)
Specifications:
Power: 120VAC, 60Hz
Loading: 10 Amp Max Smart Outlet
15 Amp Max Always-On Outlet
Total(Both Outlets): 15 Amp Max
Frequency: 908.42MHz
FCC ID: OXGZW36
IC: 10460A-ZW36
Installation Manual
One Z-Wave controlled AC outlet for standard incandescent
lighting, CFL/LED, fans or small appliances. Total load
capacity for both outlets is 1800W (15A) Resistive.
Put the Z-wave interface controller into
“Add” mode, triple press the Program
button (A).
It will be included to network.
(Once your controller confirmed, refresh
the Z-Wave network to optimize
performance. )
Put the Z-Wave interface controller
into "Remove" mode, triple press the
Program button (A). It will be excluded
to network.
Press and hold button 5S while power on.
Note: This should only be used in the event your network’s
primary controller is missing or otherwise inoperable
Note:
Your device may need to be within 100 feet of the
controller to be included. If so, include the device to the
network within 10 feet of the controller and relocate it to
the desired position in your home. Be sure to refresh the
network if the device is included in this manner.
Add to Z-Wave Network
Remove from Z-Wave Network
1: LED Indicator
Parameter=1, Size=1, Value=0 On when On and Off when Off
Value=1 On when Off and Off when On
Value=2 Always Off
Default =0
2: Auto Turn-Off Timer
Parameter=2, Size=4, Values: 0 - 65535 (M); default 0M
3: Auto Turn-OnTimer
Parameter=3, Size=4, Values: 0 - 65535 (M); default 0M
4: Restores state after power failure
Parameter=4, Size=1, Value=0 out put the state after power
Value=1 output off
Value=2 output on
Default =0
5:Association(Support 2 group, each group max support 5
devices)
Group 1 lifeline
Group 2 Relay on/off send basic set
Special Settings
Press and hold 5 s on Button (A) = Change LED Status
Plug the light you want to control into the Z-Wave Smart plug
controlled outlet .
NOTE: Plug directly into outlet, do not use with extension cords
To return your switch to factory defaults
Parameter Settings
Always On Outlet
Manual / Program button
Single press: manually turn
on/off your device.
This outlet can remotely turn
On/Off the connected device
Smart Outlet
100 feet
INTRODUCTION
The EVA LOGIK ZW36 is a Z-Wave enabled 15A receptacle
designed for most residential lighting and motor applications. It's
compatible with LED, halogen, incandescent, xenon, fluorescent
and compact fluorescent bulbs.The ZW36 fully works with the
Fibaro, Smartthings, Wink hub as well as all other certified Z-Wave
controllers.

GENERIC DEVICE CLASS:
10 - GENERIC_TYPE_SWITCH_BINARY
SPECIFIC DEVICE CLASS:
01 - SPECIFIC_TYPE_POWER_SWITCH_BINARY
COMMANDCLASS:
5E - COMMAND_CLASS_ZWAVEPLUS_INFO
86 - COMMAND_CLASS_VERSION
72 - COMMAND_CLASS_MANUFACTURER_SPECIFIC
5A - COMMAND_CLASS_DEVICE_RESET_LOCALLY
85 - COMMAND_CLASS_ASSOCIATION
59 - COMMAND_CLASS_ASSOCIATION_GRP_INFO
73 - COMMAND_CLASS_POWERLEVEL
25 - COMMAND_CLASS_SWITCH_BINARY
27 - COMMAND_CLASS_SWITCH_ALL
70 - COMMAND_CLASS_CONFIGURATION
8E - COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
55 - COMMAND_CLASS_TRANSPORT_SERVICE
9F - COMMAND_CLASS_SECURITY_2
6C - COMMAND_CLASS_SUPERVISION
7A - COMMAND_CLASS_FIRMWARE_UPDATE_MD
This device complies with part 15 of the FCC and Industry Canada
license-exempt RSSstandard(s). Operation is subjected to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment intoan outlet on a circuitdifferent from
that to which the receiver is connected.
—Consult the dealer oran experienced radio/TV technicianfor help
To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted.
Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user’s authority to
operate the device.
The manufacturer is not responsiblefor any radioorTV
interference caused by unauthorized modifications to this equipment.
Such modifications could void the user’s authority to operate the
equipment.
www.nie-tech.com
Risk of Fire
Risk of Electrical Shock
Risk of Burns
CAUTION - PLEASE READ!
This device (ZW36) is intended for installation in accordance with
the National Electric Code and local regulations in the United
States, or the Canadian Electrical Code and local regulations in
Canada. If you are unsure or uncomfortable about performing
this installation consult a qualified electrician.
Please exercise EXTREME CAUTION when using Z-Wave devices
to control appliances. Reason being is because the appliance you
want to control may be in a separate room and if unintentional
behavior occurs (such as adevice turning on or off - either
intentionally via schedules, or unintentionally via network error)
this event may lead to a hazardous condition. For these reasons,
please note the following suggestions:
1) Do not include Z-Wave devices in Groups or Scenes if they
control appliances.
2) Do not use Z-Wave devices to control electric heaters or any
other appliances which may present a hazardous condition due
to unattended, unintentional, or automatic power control
WARNING - SHOCK HAZARD
TURN OFF THE POWER to the circuit for the switch and lighting
fixture at the service panel (circuit breaker) prior to installation.
ALL WIRING CONNECTIONS MUST BE MADE WITH THE POWER
OFF to avoid personal injury and/or damage to the switch.
Please DO NOT use this switch to congrol Medical or Life Support
equipment. Z-Wave devices should never be used to control the
On/Off status of Medical and/or Life Support equipment.
COMMANDCLASS
OTHER WARNINGS
MEDICAL EQUIPMENT
CONTROLLING APPLIANCES
FCC / IC
FCC NOTE:
NOTE:
Important note:
V2.0 2019/09/02