EVERSPRING SE203 User manual

SE203
OUTDOOR SIREN
General Introduction
The SE203 is an outdoor siren powered by DC adaptor or battery. By its visible
presence, the external siren indicates that an alarm system is installed and deters
intruders. In case of intrusion, it emits a high-decibel piercing sound to alert the
neighborhood coupled with flashing red light.
It integrates a tamper protection switch for its own protection and will generate a full
alarm should there be any unauthorized attempt to remove it from its location or
open its cover.
Main features:
● IP44 approved for outdoor installation;
● Buzzer sound can be set low (85dB) or high (100dB) sound.
●Alarm duration can be adjusted from control panel.
● Configurable arm/disarm and entry/exit delay beep sound
●Informs about alarm, exit/entry delays and status changing
●Tamper switch to detect removal of its cover
● Power Supply: 9V~12V/1A power adaptor or 4 * 1.5V LR14 batteries
Product Overview
Pairing to Controller
1. Insert 4* LR14 (C-cell) batteries into the battery compartment.
2. Log into the VIAS account from the APP, and enter the controller to system
main control page.
3. Select Menu List>System Setup>ADD DEVICE>choose SE203 Outdoor
Battery Siren.
4. Please follow and complete the instruction on the APP to pairing with central
controller.
5. Locate the learning button. Do not activate pairing on the controller yet.
6. Press and hold the learning button for more than 3 seconds until the LED start
blinking.
7. Quickly activate pairing on the controller. The LED should stop blinking
indicating the pairing process is complete.
Mounting the Outdoor Siren
Choosing a location
The Siren should be mounted:
as high as possible in a prominent position so that it can be easily seen and
heard.
on a flat surface so that the rear tamper switch is not easily activated. Ensure
also that the tamper switch does not fall into the recess between brick
courses as this could prevent the switch from closing and give a permanent
tamper signal.
ideally on a south facing wall to receive optimum amount of sunlight, but an
east or west facing wall will also suffice. Avoid mounting on a north facing
wall, and avoid shadows cast by neighboring walls, trees, and roof
overhangs.
at least 1 meter away from any external or internal metalwork which can affect
its radio transmission.
Installation
1. To install the siren on the wall, first affix its back cover on the wall and then
followed by mounting its main body onto the back cover.
2. Remove the back cover again. Using the back cover itself as a template,
position the back cover on the wall and mark the positions of four mounting
holes.
3. Drill four 6mm holes and insert the wall plugs.
4. Fit two 30mm fixing screws in the top holes leaving approximately 10mm of the
screw protruding.
5. Place the top keyhole slots of the back cover over the screw heads. Adjust the
back cover position and adjust the screws until they form a neat fit with minimal
movement.
6. Secure the back cover in position using the two 25mm fixing screws at the
bottom.
FRONT VIEW
INSIDE VIEW OF SIREN MAIN BODY
(BACK COVER REMOVED)
Strobe light & red LED
1.5V LR14*4
Battery
Learning Button
Tamper Switch
Siren
Adaptor Connector

7. Before mounting the main body, ensure the waterproof cover of the Control box
has been secured back if it was removed earlier.
8. To mount the main body, hinge the front cover tabs over the top edge of the
back cover and carefully push the base of the siren cover into place. Secure the
main body in place by refitting the fixing screw in the bottom edge of the cover.
Do not over tighten the screw as this could damage the thread.
IMPORTANT: Ensure that the rear tamper switch is closed when the main body is
fitted (i.e. listen for the switch to click). If the switch does not close, this will prevent
the Siren from operating correctly. If necessary, remove the main body again and
adjust the screw on the back cover tamper plunger to ensure the switch closes
when the siren is secured in position.
Note: removing the main unit from its back plate will cause the Tamper alarm to
sound. Quickly disarm the alarm panel if this happens.
9. Upon completion of mounting the main body on the wall, the Strobe LED will
flash two times as an indication of normal operation.
Status indication
Status
LED Indication
Beep indication
Buzzer
No ID code
LED flash every 2
seconds
About to learn the
ID code by
pressing the
learning button
LED Illuminates
when pressing the
learning button
within 3 seconds.
LED flashes every
0.5 seconds by
pressing the
learning button for
more than 3
seconds
Under learning
the ID code
LED flashes every
0.5 seconds
repeatedly
Success in
learning the ID
code
LED illuminates for
0.5 seconds then
extinguishing
Failure learning
the ID code
LED flashes 3
times rapidly(0.1
sec. on/0.1 sec.
off)
Clear the ID code
LED illuminates
when pressing the
learning button.
LED extinguishes
after successful
Fit two 30mm fixing screws in
the top holes leaving
approximately 10mm of the
screw protruding
Secure back cover using
two 25mm fixing screws at
the bottom
Back
Cover

clearance.
Standby(Arm
mode)
LED flashes once
every 15 seconds
Entry/Exit Delay
LED flashes with
beep sounds
T>5 second, Beep
once every
second，
T<6 second, Beep
two times every
second
And then beep
rapidly in final 5
seconds
0= quiet
Fully Arm/Partial
Arm the system
Flash 1 time
Long Beep one
time
Disarm the
system
Flash two times
Beep- Beep two
sounds
Alarm
LED & Strobe
flashes
180
seconds(default)
Low battery
LED flashes 20
times
APP Configuration Setting
Go to device list, press and hold SE203 icons for 2secs can get into sensor
information page, press settings on the top right to get into the following selections.
Siren Sound
-High
-Low
Exit/ Entry delay beep sound
-Enable
-Disable
Siren alarm sensor tamper during Disarm
-Enable
-Disable
Beep sound when Arm/Disarm
-Enable
-Disable
Strobe light during alarm
-Enable
-Disable
LED periodic blink whenArm
-Enable
-Disable

Alarm Advanced Setting
The settings for various security delay or timing options can be found.
Please Press central alarm button>go to settings>Choose selection List icon on the
top right corner.
The following actions for siren during alarms can be adjusted on list of security
settings.
Entry Delay/Exit Delay time: 5-180secs
Enable or disable Intruder Siren when alarm
Intruder Siren Duration time from: 5-180 secs
Enable or disable Tamper Siren when alarm
Tamper Siren duration: 5-180secs
Enable or disable Panic Siren when alarm
Panic Siren Duration: 5-180secs
Enable or disable flood Siren when alarm
Flood Siren Duration: 5-180secs
Enable or disable Smoke Siren when alarm
Smoke Siren Duration: 5-180secs
Enable or disable SOS Siren when alarm
SOS Siren Duration: 5-180secs
Power Source and Icons
Power Source
Level
Icon Indication
Battery only
Full
Low Battery
DC+Battery
Battery Full
Low Battery
DC only

Operation
1. Alarm Activation:
When an alarm is activated, the siren will activate its siren and strobe light for
3 minutes (default setting), the icon will show as below.
2. Tamper Protection:
The siren is protected by a tamper switch which is compressed against the
mounting surface when mounted. Whenever the siren is removed from
mounted location, or its cover opened, the tamper switch will be activated and
the siren will send a tamper open signal to remind the user of the condition..
Maintenance
1. When the battery becomes low, the siren will report back to the controller and
LED will flash 20 times. ( The siren will not emit beep-beep sound only LED flashes
20 times when disarm mode.)
2. Once mains power loss, the siren will report to the controller and shift to backup
batteries.
Software reporting commands
Auto report
When battery is inserted, it will report to controller after 2
minutes. It will report tamper/battery/siren and DC adaptor
condition every hour.
Status change
Tamper switch is release: It will report to controller and will
activate alarm sound.
Temperature report
It will report to controller every half of hour.
Power Supply
report
When first power on, it will report power source to controller
after 2 minutes. And then it will report every hour.
Troubleshooting
The troubleshooting table lists some possible causes and solutions. Please contact
your original retailer or nearest service center if the below solutions cannot solve
your problem.
Symptom
Possible Cause
Recommendation
LED on siren not
illuminating
Improper battery
connection or reverse
polarity
Check if 4 batteries are
inserted properly.
Siren is out of order
Do not attempt to open
the casing as it will
invalidate the warranty.
Send it for repair.
LED on siren operating,
but cannot learn the ID
code or take control of
siren
Failure learning the ID
code under Siren
controlled system
According to the
operating instruction,
resume learning the ID
code process.
Ensure it is set at siren
controlled
system
Radio channel
interference
Wait for a moment to start
operating
The siren doesn’t
respond to alerts and
system changes.
The binding process has
failed
Please follow the
instructions about pairing
to controller.
The siren cannot
communicate with the
controller.
Place the siren closer to
the controller.

Reset to factory default:
To reset SE203 back to factory default state:
1. Press and hold the binding button for more than 3 seconds then release the
learning button. The RED LED will flash repeatedly.
2. Press and hold again the learning button, this time for more than 6 seconds
then release. The siren is now reset back to factory default.
Specifications
Operating Temperature
-20°C to 50°C
Main Power Supply
9V~12V/1A
Optional Power Supply
1.5V LR14 battery x 4
Battery Life
Up to 4 years ( alarm trigger one time every month)
RF Range
EU: Up to 800 meters line of sight
US: Up to 400 meters line of sight
Alarm Sound
High: 100dBA@1m; Low: 85 dBA@1m
Protection Class
IP44
Frequency Range
EU: 868 HMz
US: 923 MHz
Specifications are subject to change without notice
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de
distance entre la source de rayonnement et votre corps.
WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old
appliance for disposal at least for free of charge.
www.everspring.com
50 Sect. 1 Zhonghua Rd Tucheng
NewTaipeiCity 236 Taiwan..