Exodraft RSVG User manual

Your energy. Optimized.
Chimney Fan
RSVG
UK |Read and save these instructions!

RSV og GSV og RSVG

Your energy. Optimized.
Chimney Fan | RSVG
Content
Product information 7
Scope of supply 7
Accessories and spare parts 7
Technical specications 8
Precautions and user instructions 11
Mechanical installation 12
Transportation safety bracket 12
Minimum distance 13
Installation onto a brick chimney 14
Installation onto a steel chimney 16
Multiple fans on chimney 19
Electrical installation 20
Isolation switch 20
Startup and conguration 21
System testing 21
Operating the replace using the EFC21 controller 21
Commissioning of the chimney fan 22
Maintenance and troubleshooting 23
Care and cleaning 23
Troubleshooting 24
UK Conformity Assessed 25
Declaration of Conformity 26

Disposal
Electrical and electronic equipment (EEE) often contain materials, components and substances
that may harm the environment or be hazardous to your health. Products (WEEE) marked with
the ‘crossed-out wheeled bin’ symbol should be disposed of separately from other waste at
the end of its life. Though legislation may differ from country to country we strongly advise
that electrical and electronic waste is separated from other waste and disposed of according to
national legislation to protect the environment and personnel that may come into contact with
waste.
How to use this manual
This manual has been prepared based on the specific product and
contains relevant technical information and installations guides.
Accessories and spare parts are not covered by this manual.
Please refer to the individual manuals of these components.
This installation manual does not contain any system design documentation.
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
Errors and omissions excepted.

Disposal
Electrical and electronic equipment (EEE) often contain materials, components and substances
that may harm the environment or be hazardous to your health. Products (WEEE) marked with
the ‘crossed-out wheeled bin’ symbol should be disposed of separately from other waste at
the end of its life. Though legislation may differ from country to country we strongly advise
that electrical and electronic waste is separated from other waste and disposed of according to
national legislation to protect the environment and personnel that may come into contact with
waste.
How to use this manual
This manual has been prepared based on the specific product and
contains relevant technical information and installations guides.
Accessories and spare parts are not covered by this manual.
Please refer to the individual manuals of these components.
This installation manual does not contain any system design documentation.
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
Errors and omissions excepted.
Symbols
The following symbols may be used in the manual
to draw attention to danger or risk of personal
injury or damage to the product.
General prohibition
Failure to observe instructions marked with the prohibited
symbol may result in extreme danger or serious personal injury.
General warning
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
General attention
Marks a dangerous situation that, in the worst-case scenario,
can cause serious personal injury or significant damage to the product.
Electricity hazard/High Voltage
Marks a situation in which caution is advised due to the risk of high voltage electric
shock which can cause serious personal injury or significant damage to the product.
Connect an earth terminal to the ground
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
Permitted and approved
Permitted and approved method of installation.
Prohibited and not approved
Prohibited and not approved method of installation.

Warning
To minimise the risk of fire, electric shock, personal injury
and/or damage to the product please observe the following:
• Please always read the manual and only use the product in accordance with the
manufacturer’s instructions. If in doubt, contact one of the Exodraft specialized dealers.
• All installations must be carried out by properly qualifi ed personnel in accordance with
national legislation and regulations.
• This product must be earthed. Get assistance from an qualifi ed electrician when in doubt.
• The chimney fan must always remain switched on when the fireplace is in use.
• Ensure that the chimney has been swept before mounting the fan to avoid chimney fires.
• Prior to servicing the product, disconnect the power and ensure that it cannot accidentally
be reconnected.
• Exodraft always recommends the use of a smoke alarm when a solid fuel fireplace is
installed.
• If the Exodraft fan system has been designed for solid fuel/multi fuel installations, please
ensure that the design meets the requirements of BS EN15287-1. If this cannot be achie-
ved, a smoke alarm must be installed in the same room as the heat appliance.
• Note! Fans serving biomass boilers must be cleaned more often due to extensive residue/
soot building. It is essential that a regular inspection and cleaning schedule is implemen-
ted, especially in the early days of usage, to experience how often regular inspections and
cleaning should be carried out.
UK
Your energy. Optimized.

UK |7
3112004_RSVG_UK
Warning
To minimise the risk of fire, electric shock, personal injury
and/or damage to the product please observe the following:
• Please always read the manual and only use the product in accordance with the
manufacturer’s instructions. If in doubt, contact one of the Exodraft specialized dealers.
• All installations must be carried out by properly qualifi ed personnel in accordance with
national legislation and regulations.
• This product must be earthed. Get assistance from an qualifi ed electrician when in doubt.
• The chimney fan must always remain switched on when the fireplace is in use.
• Ensure that the chimney has been swept before mounting the fan to avoid chimney fires.
• Prior to servicing the product, disconnect the power and ensure that it cannot accidentally
be reconnected.
• Exodraft always recommends the use of a smoke alarm when a solid fuel fireplace is
installed.
• If the Exodraft fan system has been designed for solid fuel/multi fuel installations, please
ensure that the design meets the requirements of BS EN15287-1. If this cannot be achie-
ved, a smoke alarm must be installed in the same room as the heat appliance.
• Note! Fans serving biomass boilers must be cleaned more often due to extensive residue/
soot building. It is essential that a regular inspection and cleaning schedule is implemen-
ted, especially in the early days of usage, to experience how often regular inspections and
cleaning should be carried out.
UK
Your energy. Optimized.
Product information
An Exodraft RSVG chimney fan is designed with vertical discharge.
The fan must be installed on top of a chimney and creates a negative pressure (suction) along the full
length of the ue.
The fan is developed with a fail-safe ue system, specically for gas replaces and individual gas-red
boilers.
The fan is part of an Exodraft system and should be connected to an EFC21 Exodraft controller for
optimal effect.
Please check out this site for advice about other Exodraft products:
www.exodraft.com
Scope of supply
• Exodraft RSVG chimney fan
• Mineral wool mat for vibration-free mounting
• Packet with location brackets, safety wire, bolts and nuts
(wing screws included - to be used where allowed)
• Armoured hose
• Installation manual and user instructions
Accessories and spare parts
The table below shows the accessories and spare parts available for the RSVG-models.
Accessories* Spare parts
Flanges (for steel chimneys) Motors
Cover Plates (for steel and brick chimneys) Impellers and axial vanes
RSD - Dilution bolts (for brick chimneys) Mineral wool mats
Rainshield SVD-RS - Vibrations dampers (for anges on steel chimneys)
Capacitors
PDS - Pressure differential switch
*This manual does not describe the specic use of accessories. We refer to the separate manuals for such components.
For more details contact your Exodraft dealer.

8|UK
Your energy. Optimized.
Warranty
All Exodraft products are covered by a 2-year guarantee as per European consumer rights legislation. For
some countries an extended period of guarantee may apply depending on either national legislation or
other clearly stipulated conditions. Customer complaints must be handled by a specialised dealer or
wholesaler (preferably where the Exodraft product has been bought originally). An updated list of Exodraft
specialised dealers can be found on our website for the country in question.
Exodraft products must always be installed by properly qualied personnel. Exodraft reserves the right to
change these guidelines without prior notice.
The warranty and liability does not cover instances regarding personal injury or damage to property or the
product that can be ascribed to one or more of the following causes:
• Failure to follow this installation and operation manual
• Incorrect installation, start-up, maintenance or servicing
• Improper repairs
• Unauthorised structural modications made to the product
• Installation of additional components that have not been tested/approved with the product
• Any damage resulting from continued use of the product despite an evident defect
• Failure to use original spareparts and accessories
• Failure to use the product as intended
• Exceeding or failure to meet the limit values in the technical data
• Force majeure
Technical specications
The RSVG fan is designed for vertical discharge. It is available in three sizes.
The body and casing are manufactured in cast aluminium and equipped with a centrifugal impeller.
Chimney fan Axial vane
RSVG200-41
RSVG250-41
RSVG315-41
Cast aluminium impeller
All models can be opened for service and cleaning purposes.
The chimney fan has a built-in fail-safe system consisting of a pressure differential switch (PDS) and two
pressure sensors, ensuring correct airow when the re is used. Drainage holes have been built into the
base plate of the RSVG.
The sound level is below 60 dB (measured at a distance greater than 2.5 metre away from the fan) if
installed correctly. Further information about sound levels available in our technical brochure/datasheet.
The RSVG chimney fan is designed to operate with a maximum ue gas temperature of 250 °C.
The run capacitor is considered a wear part and will need to be replaced depending on usage.

UK |9
3112004_RSVG_UK
Technical data
Model Motor specications Weight Dimension [mm]
rpm V Amp kW* kg A B C [Ø] DE [Ø]
RSVG200-41 1400 1 x 230 0.4 0.07 18 280 390 310 200 80
RSVG250-41 1400 1 x 230 0.8 0.16 27 335 485 385 250 100
RSVG315-41 1400 1 x 230 1.8 0.37 37 380 580 465 315 115
*Effect at the motor shaft at ambient temperature of 20 °C
• The RPM of the above fan models are innitely adjustable
• Motor protection IP rating IP54
• Insulation class F
A
B
D
E
C
RSV og GSV og RSVG

10 |UK
Your energy. Optimized.
Construction and components
1 Top section
2 Bottom section
3Motor
4 Centrifugal impeller
5 Inlet ring
6 Safety hinge
7 Safety mesh
8Handle
9
Screws to secure top and bottom section.
Alternatively, use supplied wing screws
where conditions allow.
10 Pressure differential switch (PDS)
11 Fixed air pressure sensors
12 Armoured cable and connecting cable
13 Mineral wool mat
14 Safety wire
15 Location brackets, bolts and nuts etc.
13
15
14
12
3
4
6
7
8
9
1
2
10
11
5