Exodraft RSHG User manual

UK
DE
RSHG
UK Read and save these instructions!
DE Lesen Sie diese Anleitung und bewahren sie sie auf!

1. UK – Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Construction and design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Commissioning of the chimney fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5 Service and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.6 Technical specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.7 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. DE - Produktinformationen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Konstruktion und Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Installationsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3 Verdrahtung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4 Inbetriebnahme des Abgasventilator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5 Wartung und Reinigung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6 Wichtiger Hinweis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.7 Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3. Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3000126-RSHG-UK-DE 20200204
2

1. UK – Product information
The exodraft Chimney Fan type RSHG is used as part of the fail-safe ue system for open ued gas
appliances, such as stoves and domestic boliers. The RSHG gives a horisontal discharge of the ue
gases. Max. 200 °C
All installations must be carried out by competent personnel
inaccordance with national laws and regulations
Warning!
Avoid chimney res – ensure that the chimney has been swept
before mounting the fan.
The chimney fan must always be operating when the replace is
in use.
Please always read the installation instructions for the exodraft
control unit, before installation of the chimney fan.
1.1 Construction and design
Construction
The body and casing are manufactured in cast aluminium, tted with a stainless steel vane and
non-moving airpres-sure sensors linked to a pressure dierential switch (PDS), ensuring correct
airow when the re is used. The chimney fan can be opened for service and cleaning purposes.
Main parts
The RSHG has the following main components
a Motor housing
b Bottom section
c Motor
d Cooling plates
e Vane
f Safety hinge
g Safety net
h Armoured motor cable
i Mineral wool mat
j Safety wire with bolt and rawlplug
k Location brackets, bolts and nuts
l Pressure dierential switch
m Non-moving airpressure sensors
3000126-RSHG-UK-DE 20200204 UK • 3

1.2 Installation instructions
Before tting onto a chimney
If ... then ...
the fan is to be mounted onto a brick chimney the chimney must have location brackets – see below
the fan is to be mounted onto a steel chimney a ange is required (supplied as an extra ) -see below
it is an RSHG014
remove the transport safety bolt on the hinges
before mounting.
Before tting onto the brickwork of a chimney
Step Action
1 Measure the inside diameter of the chimney and
cut the size of the hole in the mineral wool mat
accordingly.
Note that there must always be a minimum of
20 mm of mat surface at any point around the
circumference of the hole.
2 Mount and fasten the location brackets in the
underside of the base plate by means of the bolts
and nuts supplied.
Please notice that the bolt is to be inserted from
beneath.
3 Adjust the distance between the location brackets
to t the inside diameter of the chimney, and then
tighten the nuts. Note that there should be a 2-4
mm gap between the brackets and the chimney so
as to avoid transmitting vibrations from the fan to
the chimney.
A and B measurements – please refer to step 1.
3000126-RSHG-UK-DE 20200204
4• UK

Before tting onto a steel chimney
Step Action
1 A ange (C) is used, tted so that the spigot end sits
inside the chimney (D). A
B
C
D
2 Place the mineral wool mat (B) on the ange (D) and cut
a hole in the mineral wool mat (the hole being the same
diameter as the ange hole).
3Cut the corners of the mineral wool mat, so there is room
to t the vibration dampers (B).
If a temperature sensor is to be installed with the
chimney fan, make room for it by cutting a piece of the
mineral wool mat. This also ensures that the mat sits
level on the chimney.
4 Fit the ange to the chimney fan, with the use of
vibration dampers supplied with the ange.
5 The fan can now be tted onto the chimney.
Fitting the chimney fan onto the chimney
Step Action
1 The chimney fan can now be tted into place. Place the
mi¬neral wool mat on top of the chimney (it can be used
with either side facing the fan), and place the fan on top.
3000126-RSHG-UK-DE 20200204 UK • 5

Step Action
2 Mount the safety wire in the chimney (1). Use the
supplied screw and rawl-plug in brick chimney and the
self-cutting screw in steel chimney. Then mount the wire
through the hole in the base plate and into the wire lock.
Tighten the safety wire slightly and tighten the wire lock
(2), so that the chimney fan is secured when opened for
service and cleaning purposes.
The isolation switch should be tted onto the side of the
chimney (3), so it is easily accessible when servicing the
fan. The armoured cable should be connected into the
underside of the isolator and up into the switch via the
coupling.
3 Before starting up, make sure that:
- the nuts in the location brackets are tightened (4)
- the chimney fan is closed and the screw
tightened (5)
- the safety wire is clamped to the chimney (6)
- the safety wire and the wire lock are tightened (7)
- the grommet on the armoured cable is fastened (8)
- the end-user is aware of the fact that the chimney fan
must always be operating when the replace/boiler is
in use
3000126-RSHG-UK-DE 20200204
6• UK

1.3 Wiring
Fan and motor specications are provided on the fan’s type plate. All the single-phased models are
adjustable.
Wires are to be connected as per the wiring diagram. For further details, please see guidelines for
the exodraft control units. All exodraft fans require extra safeguards in accordance with power
current regulations.
Any lightning conductor connected to the fan must respect current applicable legislation.
exodraft-motor Grundfos-motor
87 6 5 4 321
AUX
MAIN
t°
P
BN
BK
BU
4
5
3
1
2
1
2
3
4
NO
NC
C
N
L1 5
YEGN
POWER SUPPLY
1 x 230 V ~ 50 Hz
6 x 0,75
BK
BN
BU
3 x 0,75
YEGN
Isolation switch
In accordance with the provisions of the EU Machinery Directive* a chimney fan
must always have an isolation switch tted. The isolation switch must comply with national wiring
standards.
The isolation switch must be ordered separately, as it is not part of the standard exodraft chimney
fan delivery.
*Please refer to Machine Directive (2006/42/EF/-EEC/-EWG/-CEE) – Appendix 1 item 1.6.3 “Separation of the sources of
energy.
1.4 Commissioning of the chimney fan
The chimney draught must be checked when
commissioning the fan. The pressure dierential switch
(PDS) might need adjusting during commissioning. The
PDS must be set so that the fail-safe system will cut out
when the volume of ue gases falls below a set level.
During such a test, all windows and doors must be
closed and any ventilation fans switched on. Please refer
to the relevant exodraft Gas Fan Controller Installation
Instructions for guidance.
As illustrated, remove the top cover and adjust the (PDS)
to the required value.
PDS
3000126-RSHG-UK-DE 20200204 UK • 7

1.5 Service and cleaning
Warning!
• The ow sensors must not be bent or moved, as this might aect their performance.
The motor has special ball bearings that are sealed, lifetime lubricated and maintenance-free. If
replacement of the bearings is required, this should be carried out by qualied professionals.
Inspection and
cleaning
The fan should be checked and cleaned as required (at least once a year) :
Step Action
1 Use the isolation switch to switch o the fan. Wait
until the fan stops rotating.
A
2 Loosen the screw (A) and open the top section of
the fan so that it hangs on its hinges and the safety
wire.
3 Remove any deposits on the vane and the pressure
sensors. Test the fail-safe system and check
whether it is damaged in any way.
4 Check the path taken by the smoke through
the top and bottom sections of the fan for soot
deposits, and clean where necessary with a scraper
or brush.
5 When the fan is open, it is also possible to sweep
the chimney.
Regarding installations in UK:
Gas appliances should be checked for safety once a year by a CORGI registered installer. Details of
local installers can be obtained by ringing CORGI on 0870 401 2300 or by accessing the website at
www.trustcorgi.com.
1.6 Technical specications
The sound level is below 67 dB at a distance greater than one metre away from the RSHG fan when
it is correctly tted. Further information is available in the catalogue.
The ue gases must not exceed 200 °C
1.7 Warranty
exodraft provides a two-year factory warranty on its chimney fans, valid from invoice date.
exodraft fans must be installed by competent personnel.
exodraft reserves the right to introduce changes to these guidelines without prior notice.
3000126-RSHG-UK-DE 20200204
8• UK

2. DE - Produktinformationen
Der exodraft Abgasventilatoren Typ RSHG wird als Teil ausfallsicherer Abgasanlagen für
oene Gasgeräte, wie Kaminöfen und Kessel, verwendet. Der RSHG erzeugt eine horizontale
Rauchgasableitung. Max. 200 °C.
Alle Installationen müssen in Übereinstimmung mit national
gültigen Gesetzen und Vorschriften durch Fachpersonal
durchgeführt werd
Warnung!
Vermeiden Sie Feuer im Schornstein - Sorgen Sie dafür, dass der
Schornstein vor der Montage des Abgasventilatorens gefegt
wurde.
Der Abgasventilatoren muss immer in Betrieb sein, wenn die
Feuerstätte in Betrieb ist.
Bitte lesen Sie vor der Installation des Abgasventilatorens die
Installationsanweisungen für den exodraft-Regler.
2.1 Konstruktion und Design
Konstruktion
Das Gehäuse ist aus Aluminiumguss gefertigt und der Ventilator mit einem Edelstahlügel
ausgestattet. Über unbewegliche Luftdruck-Sensoren ist eine Sicherheitsabschaltung (PDS) mit
Wechsler verbunden, um einen korrekten Luftstrom zu gewährliesten. Der Abgasventilator kann
für Wartungs- und Reinigungsarbeiten aufgeklappt werden.
Hauptteile
Der RSHG hat folgende Hauptkomponenten
a Motorgehäuse
b Unterteil
c Motor
d Kühlplatten
e Flügel
f Sicherheitsscharnier
g Sicherheitsnetz
h Sicherheitsummanteltes Motorkabel
i Mineralwollmatte
j Sicherheitsdraht mit Schraube und Dübel
k Fixierklammern, Schrauben und Muttern
l Sicherheitsabschaltung (PDS)
m Unbewegliche Luftdruck-Sensoren
3000126-RSHG-UK-DE 20200204 DE • 9

3000126-RSHG-UK-DE 20200204
10 • DE
2.2 Installationsanleitung
Vor dem Einbau in einen Schornstein
Wenn ... Dann ...
der Lüfter auf einem gemauerten Schornstein
montiert werden soll
müssen die Fixierklammern für den Schornstein
verwendet werden - siehe unten
der Lüfter auf einem Stahl-Schornstein montiert
werden soll
ist ein Flansch erforderlich (im Lieferumfang enthalten)
- siehe unten
es ein RSHG014 ist
entfernen Sie die Transportsicherungsschrauben
an den Schranieren vor der Montage
Vor der Montage auf das Mauerwerk eines Kamins
Schritt Aktion
1 Messen Sie den Innendurchmesser des Schornsteins
und schneiden Sie ein entsprechendes Loch in die
Mineralwollmatte.
Beachten Sie, dass immer mindestens 20 mm
Mattenoberäche um das Loch herum vorhanden
sein müssen.
2 Montieren und befestigen Sie mit den
mitgelieferten Schrauben und Muttern die
Fixierklammern an der Unterseite der Basisplatte.
Bitte beachten Sie, dass die Schrauben von unten
eingeführt werden müssen.