Extang Trifecta 2.0 Assembly instructions

It is important that all areas
where the bed cover mounts
are clean and free of debris
prior to installing.
Place assembled cover over the cab
end of the truck box.
The Trifecta 2.0 truck bed cover
comes fully assembled.
Note any damaged or missing
components before installing.
Unfold the cover fully and adjust
position over the truck bed for proper
front (cab) / rear (tailgate) alignment.
Carefully refold the cover without
shifting its position on the truck bed.

For bed caps, trim only enough of the
bed cap edge so the rear (tailgate) clamp
contacts the bottom of the metal ange.
For bed liners that cover the metal ange,
trim a minimum of 100 mm or 4” of the
liner wall so the clamps contact the bottom
of the metal ange.
100mm
4.0”
The front (cab) clamp stows in the
cover rail. Rotate the clamp
down and slide it at an angle
towards the bed rail.
Rotate the body
of the clamp up
or down to match
it’s position with the bed rail
flange. Swing the
clamp vertically and align the
clamp jaw under the metal
truck bed flange.
Tighten the T-handle by hand.
Do not use a wrench.
If your truck has a bed cap or
bedliner that covers the metal
bed wall ange, you will need
to remove enough so that all
the clamps make solid contact.
The rear (tailgate) clamps are stowed in the cover rail,
rotate the clamp down and slide it at an angle to the
truck bed rail.
To aid in better water management
and the straight appearance of the cover,
push down on the cover to compress the
seals while tightening the clamps.
Position the
clamp body
so that the
bottom
ridges
match the
bottom of
the
metal
flange.
The clamps should be
slid as far over to the
rail as possible.
To lock the cover, pull
the clamps straight
down and release to
hook under the bottom
of the bed rail.
With the tailgate open and the
front (cab) clamps secure,
completely close the cover.

To prepare the Trifecta 2.0 to
drive in the open position,
release the rear (tailgate)
clamps and fold the
cover forward.
Fold the cover forward
and fasten BOTH straps
in the middle section
to the front rail.
IMPORTANT: Before folding
the second section of the
cover, the rear (tailgate) clamps
must be stowed securely
into the rail.
Do NOT tow your vehicle from the rear with
any Extang bed cover on your truck
Front (cab
clamp)
Rear (tailgate
clamp)
Add clamp
plate as shown
here
Front (cab clamp)
Rear (tailgate
clamp)
Add clamp
plate as shown
here
Special Instructions for Alternative Brackets
IMPORTANT NOTICE
While driving, the cover must be completely flat and secure with all four clamps
in the closed position or completely folded up (all panels) and secured
at the cab. DO NOT DRIVE with the cover in a partially open position.
Remove any snow or foreign matter
before folding
IMPORTANT
Re-tighten the front / cab clamps after the first week of driving the vehicle.
Also periodically check the clamps to ensure they are secure.

Specify: Year, Make, Model, bed length, Driver or Passenger side.
Cab Hinge
Assembly
(with Seal)
92xxx-63
93xxx-63
94xxx-63
Cab Hinge
Seal only
32920104
Rear (Tailgate)
Clamp
92xxx-77
93xxx-77
94xxx-77
Rear (Tailgate) Seal
92xxx-18
93xxx-18
94xxx-18
Tarp
92xxx-20
93xxx-20
94xxx-20
Corner Seal
92xxx-19
93xxx-19
94xxx-19
Rail Seal
92xxx-17
93xxx-17
94xxx-17
Tie Down Strap
54440400
Buckle Assembly Front
31920120
Tail Hinge
Assembly
(with Seal)
92xxx-64
93xxx-64
94xxx-64
Tail Hinge
Seal only
32920102
Front (Cab)
Clamp
92xxx-76
93xxx-76
94xxx-76
Front (Cab) Seal
92xxx-16
93xxx-16
94xxx-16
Learn more about tonneau covers on our website.