Extreme Networks AP460C Installation manual

AP460C, AP460S6C, and AP460S12C Hardware User Guide
Install and view specifications and compliance information for AP460C, AP460S6C, and AP460S12C devices.
AP460C, AP460S6C, and AP460S12C Tri Radio 802.11ax access points are based on advanced radio technology and IP67 rated for harsh and
extreme outdoor environments, with an extended temperature range from -40 C - +60 C. The tri-radio design delivers 802.11ax 2x2:2 and 4x4:4
data rates concurrently on the 2.4 and 5 GHz radios, with a third radio as a dedicated dual-band sensor.
For regulatory and compliance information, see "Regulatory Compliance Statements".
Important! Change the Country Code
If youraccess point is configured for the World Regulatory Domain, it is important to set the country code to the country in which the APwill be
deployed to meet regulatory requirements and for optimal wireless operation. To do this, follow these steps:
The country code selection is for World models only and is not available to FCC, CAN, and other country-specific models. Per FCC reg-
ulations, all Wi-Fi products marketed in the United States must be set to U.S. channels only.
1. Power on the AP and allow it to find and connect to ExtremeCloudIQ. Once the APis connected it appears in the table of devices in the
Manage > Devices window.
2. Select the check box next to the AP, and then select Assign Country Code from the Actions drop-down list. In the dialog box, select the
appropriate country from the drop-down list, and then select Save.
3. Upload your changes to the device.
Safety Guidelines
Safety Guidelines
The information in this section applies to AP460C , AP460S6C, and AP460S12C devices.
The following safety icons are used in these guidelines to identify the type of precaution:
AP460C, AP460S6C, AP460S12C Hardware Guide
1
AP460C, AP460S6C, AP460S12C Hardware Guide
1

This icon indicates a general caution. Failure to comply with a caution notification can result in damage to equipment.
This icon indicates an electrical caution. Failure to comply with an electrical notification can result in serious injury or
death, and extensive damage to equipment.
This icon indicates a laser caution. Failure to comply with a laser caution can result in serious injury.
The following table lists the safety precautions you should follow when installing your AP460C , AP460S6C, and AP460S12C devices.
Extreme Networks devices must be installed by a professional installer who is certified to install these types of devices
and to ensure that they are properly grounded and meet applicable local and national electrical codes.
These devices are intended for indoor use only.
Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
Do not install the device in an environment where the operating ambient temperature might exceed the recom-
mended ranges.
For products available in the USA/Canada market, for the 2.4 GHz band, only channels 1-11 can be operated. Selec-
tion of other channels is not possible.
Changes or modifications made to this device that are not expressly approved by the party responsible for com-
pliance could void the user's authority to operate the equipment.
Use only attachments and accessories specified by Extreme Networks.
These devices are not intended for use by persons (including children) with reduced physical, sensory, or mental cap-
abilities, or with lack of experience of knowledge unless they are given supervision or instruction concerning use of the
devices by a person who is responsible for their safety. Children should be supervised to ensure that they do not play
with the devices.
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when elec-
tronic components are improperly handled and can result in complete or intermittent failures. Be sure to follow ESD-pre-
vention procedures when handling electronic components and equipment.
During operation, the surfaces of these devices can become hot. Use caution when handling.
To meet federal radiation exposure requirements, these devices should be installed at a minimum distance of 12" (30
cm) from people or animals.
Install the AP
The following sections describe how to mount your AP in an outdoor location on a pole or flat surface.
Shipping Carton Contents
The AP460C, AP460S6C, and AP460S12C shipping carton contains the following items:
lAP460C , AP460S6C, and AP460S12C chassis with two installed M20 cable gland assemblies and plugs, and two installed M25 seal
caps.
lHardware bag containing grounding hardware (M4 screw, split washer, and lock washer)
lRead Me card.
Install the AP
AP460C, AP460S6C, AP460S12C Hardware Guide
2
AP460C, AP460S6C, AP460S12C Hardware Guide
2

Mount the AP460C, AP460S6C, or AP460S12C horizontally or vertically on a pole using the built-in brackets on the hardware, or on a solid flat sur-
face using an accessory bracket (see "Accessories "). These devices can be installed in even the most extreme outdoor environments. The fol-
lowing sections describe the installation process.
Before you install the device, make sure that you have all the materials and tools necessary, and familiarize yourself with the safety and site haz-
ard warnings.
For best performance, deploy devices in relatively open areas at least 100' (30.5 m) apart from each other.
Required Tools
To install your device horizontally or vertically on a pole, you will need the following items:
lTwo hose clamps that accommodate the diameter ofthe pole to which youare mounting the device.
lA slotted screwdriver to tighten the hose clamps.
Installation Methods
Install the Device on a Vertical or Horizontal Pole
Use the following steps to install the device on a vertical or horizontal pole.
1. Thread two hose straps of the correct diameter for the pole through the slots in on the back of the device and around the pole. Hose straps
should be 1/2" (12 or 13 mm) wide and made of stainless steel.
2. While holding the device against the pole, use a slotted screwdriver to tighten first the top and then the bottom hose strap screws to a min-
imum torque ofat least 14 inch-pounds until the device is secure. Make sure that the LANglands are facing down (earth) to eliminate the
chance of water entering the chassis. If you are installing the device to sit on top of a horizontal pole, make sure the top of the device faces
up (sky) with the LANglands are protected by the top.
AP460C, AP460S6C, AP460S12C Hardware Guide
3
AP460C, AP460S6C, AP460S12C Hardware Guide
3

Install the Device on a Flat Surface
You can Install the device on a vertical or horizontal solid flat surface using the accessory wall bracket (AH-ACC-BKT-ASM). This kit contains the
mounting bracket and four bolts without washers in the plastic bag labeled "Wall Mount". You will need to provide four mounting bolts or screws
and wall mount anchors that are appropriate for the wall type where youare installing the device.
1. Insert the four M5 bolts that come in the bracket accessory kit into the holes on the bottom of the AP and torque each bolt to 16 inch-lbs.
AP460C, AP460S6C, AP460S12C Hardware Guide
4
AP460C, AP460S6C, AP460S12C Hardware Guide
4

1. Use the bracket as atemplate to mark the location of the mounting holes in the wall. Use the holes indicted by the blue arrows in the illus-
tration below.
2. Drill a hole in the wall at each mark using a drill bit that is slightly smaller than the diameter of the screws so the screw threads will grip the wall
securely.
If you are not installing the device on a concrete wall, you can use threaded screws and screw-in wall anchors (not supplied) to mount
the device.
3. Attach the bracket to the wall using the appropriate mounting screws for the wall type.
4. Insert the heads of the bolts on the device into the large end ofthe bracket keyholes and slide the device down until the bolts rest in the
narrow end of the keyholes.
5. Tighten the locking screws on the bracket to secure the device.
3. Ground the device as shown below.
For horizontal mounts, be sure that the ports are facing earth to reduce the chance of water entering the chassis. As an added security measure,
you can thread a safety strap through one of the cable strap slots in addition to the hose strap. Connect the other end of the strap to a secure
object.
Ground the Device
Use the following steps to properly ground the AP:
1. Crimp the ground terminal onto a 10 AWG ground wire.
2. Insert the terminal on to the M4 screw, followed by the star washer.
3. insert the screw into the AP and torque it to 12 inch-lbs.
4. Connect the other end ofthe ground wire to an appropriate earthing location.
AP460C, AP460S6C, AP460S12C Hardware Guide
5
AP460C, AP460S6C, AP460S12C Hardware Guide
5

Install the Waterproof Ethernet Cable Housing
Use the waterproof Ethernet cable housing to ensure a weatherproof seal for the Ethernet cable. Use the following procedures to install the hous-
ing.
1. Remove the sealing nut, claw, and the 2-part seal from the main body of the waterproof housing. Assemble these pieces around the Eth-
ernet cable in the order shown here:
2. Insert the Ethernet cable through the sealing nut and claw.
3. Take the seal apart, insert the cable between the two halves and reassemble the seal.
4. Insert the seal into the claw.
5. Insert the Ethernet connector into the main body and into the connector in the AP until the locking tab clicks into place. Make sure that
the small tabs on the claw fit into their counterparts on the main body.
6. Insert the seal and claw into the main body.
7. Screw the threaded nut onto the threaded main bodyto a torque of 10 inch-pounds.
8. Connect the other end ofthe Ethernet cable to a PoE injector or PoE-enabled switch.
Accessories
The following accessories are available for the AP460C, AP460S6C, and AP460S12C:
lAH-ACC-PW-CBL-US: 6' 18 AWG universal power cord with US plug
lAH-ACC-PW-CBL-UK: 6' universal power cord with UK plug
AP460C, AP460S6C, AP460S12C Hardware Guide
6
AP460C, AP460S6C, AP460S12C Hardware Guide
6

lAH-ACC-PW-CBL-EU: 6' universal power cord with EUplug
lAH-ACC-PW-CBL-AU:6' universal power cord with AUplug
lAH-ACC-PW-CBL-JP: 6' universal power cord with Japan plug
lAH-ACC-PW-CBL- KR: 6' universal power cord with Korea plug
lAH-ACC-BKT-ASM: Outdoor APstainless steel wall bracket assembly.
lAH-ACC-MRN-KIT: Stainless steel accessory kit including screw pack, mounting bracket, locking screw for mounting bracket, and metal hose
strap for 1-2.75" diameter poles.
lAH-ACC-STRP-MRN: Outdoor APstainless steel hose strap for 3-15" diameter pole (larger poles).
Remove the RJ45 Cable Safely
If you need to uninstall the device for any reason, such as troubleshooting, you will need to remove the RJ45 cable. Use the following steps:
1. For ETH0 or ETH1, loosen the gland sealing nut.
2. Move the gland cap, claw and seal down the cable at least 6 inches from the LANconnector.
3. Use a thin, strong non-conductive tool, such as a flat wooden stick to reach into the main gland body and depress the plastic locking latch
on the RJ45 connector.
Be careful not to touch any components of the PCBA board near the gland area.
5. While pressing down on the latch, gently pull on and remove the cable.
6. Remove the sealing nut, claw, and seal from the cable.
Hardware Components
Youcan see the hardware components in the illustration below and readabout them in the sections that follow.
Component Descriptions
Status Light
The status light, located between the two Ethernet ports, conveys operational states forsystem power, firmware updates, Ethernet and wireless
interface activity, and major alarms. At setup, this light cycles through the following sequence:
lSolid White: The power is on and the device is operational.
lSolid Amber: The device is on and is booting..
AP460C, AP460S6C, AP460S12C Hardware Guide
7
AP460C, AP460S6C, AP460S12C Hardware Guide
7

lBlinking Amber: The device is performing a firmware upgrade.
lDark: The power is off.
Ethernet Ports
These devices have two RJ45 Ethernet ports (Eth0 and Eth1) that automatically negotiate half- and full-duplex connections with the con-
necting device. The ports are autosensing and adjust to straight-through and crossover standard Cat2, Cat5, Cat5e, or Cat6 Ethernet cables
automatically. The APreceives power through an Ethernet connection to the ETH0 port from PSE (power sourcing equipment) that is compatible
with the 802.3at and 802.3at standards.
Micro USB Console Port
Remove the waterproof screw capto access the micro USB port and the Reset button. Through the micro USB Console port you can make a
serial connection between your management system and the AP. When you connect to the device using the micro USB Console port, the man-
agement station from which you connect to the device must have a VT100 emulation program, such as Tera Term Pro©(a free terminal emu-
lator) or Hilgraeve HyperTerminal®(provided with Windows®operating systems from XPforward). The serial connection settings are: 9600 bits per
second, 8 data bits, no parity, 1 stop bit, no flow control.
You can order a micro USB console adapter cable here.
To troubleshoot these devices, you must first uninstall them from the outdoor location.
This illustration shows the USB, Micro USB and Reset buttons, which are located behind waterproof screw caps.
The pin-to-signal mapping for the Console port is shown below:
AP460C, AP460S6C, AP460S12C Hardware Guide
8
AP460C, AP460S6C, AP460S12C Hardware Guide
8

Pin Definition
1 NC
2 RxD (input to AP)
3 TxD (output to terminal)
4 Signal (GND)
5 Signal (GND)
USBPort
These devices have a standard Micro USB port that you can use to connect USB-based beacons (iBeacon, for example) and IoT (Internet of
Things) devices. To access the port, remove the gland cap screw.
Reset Button
The Reset button is located behind the same waterproof screw cap as the micro USB port. Use the Reset button to reset the device or restore the
factory default settings.
To prevent the reset button from resetting the configuration, enter this command:
no reset-button reset-config-enable
When this command is enabled, pressing the button for 5 seconds will still reboot the AP, but pressing it for more than 10 seconds will not reset its
configuration.
Hardware Specifications
The following sections list radio, device, power, and environmental specifications for these devices.
Interfaces
l100/1000/2500 Mbps auto-negotiation RJ45 Ethernet PoE port
l10/100/1000 Mbps auto-negotiation RJ45 Ethernet port
Radios
lBLE Bluetooth Low Energy
lIEEE 802.11a/b/g/n/ac/ax 4x4
lIEEE 802.11a/b/g/n/ac/ax 2x2
lIEEE 802.11a/b/g/n/ac/ax 1x1 scanner
Radio Specifications
802.11a
l5.150-5.350, 5.470 - 5.850 GHz operating frequency
lOrthogonal Frequency Division Multiplexing (OFDM) modulation
lRates (Mbps): 54, 48, 36, 24, 18, 12, 9, 6 with auto fallback
802.11b
l2.4-2.5 GHz operating frequency
lDirect-Sequence Spread-Spectrum (DSSS) modulation
lRates (Mbps): 11, 5.5, 2,1 with auto fallback
802.11g
l2.4-2.5 GHz operating frequency
lOrthogonal Frequency Division Multiplexing (OFDM) modulation
lRates (Mbps): 54, 48, 36, 24, 18, 12, 9, 6 with auto fallback
802.11n
l2.4-2.48 and 5.150-5.350, 5.470 - 5.850 GHz operating frequency
l802.11n modulation
lRates: MCS0 - MCS7 (6.5 MBps- 600Mbps)
AP460C, AP460S6C, AP460S12C Hardware Guide
9
AP460C, AP460S6C, AP460S12C Hardware Guide
9

l1x1, 2x2,4x4 MIMO radio
lHT20/HT40 support
lA-MPDU and A-MSDU frame aggregation
802.11ac
l5.150-5.350, 5.470 - 5.850 GHz operating frequency
l802.11ac modulation (256-QAM)
lRates: VHT_MCS0 - MCS9, (6.5-3467 Mbps), NSS = 1-4
l1x1, 2x2,4x4 MIMO radio
lVHT20/VHT40/VHT80 support
lTxBF (transmit beamforming)
802.11ax
l5.150-5.350, 5.470 - 5.850 GHz operating frequency
l802.11ax modulation (1024-QAM)
lDual-band OFDMA
lRates (Mbps): HE0-HE1 (8 Mbps - 1200 Mbps), NSS = 1-2
l1x1, 2x2,4x4 MIMO radio
lVHT20/VHT40/VHT80/VHT160 support
lTxBF (transmit beamforming)
802.11ax (for 5 GHz sensor)
l2.4-2.48, 5.150-5.350, 5.470 - 5.850 GHz operating frequency
l802.11ax modulation (1024-QAM)
lDual-band OFDMA
lRates (Mbps): HE_MCS0-11 (8 Mbps - 1200 Mbps), NSS = 1-4
l1x1, 2x2,4x4 MIMO radio
ll VHT20/VHT40/VHT80/VHT160 support
lTxBF (Transmit beamforming)
Transmit Power and Sensitivity Specifications
Output power may be limited by regulatory requirements.
2.4 G: Tolerance +2/-2 dB @25°C
Mode Data Rate Power Unit
11b 1,2,5.5,11 18 dBm
11g 54 Mbps 15 dBm
48 Mbps 16 dBm
36 Mbps 17 dBm
6 Mbps 18 dBm
HE20 MCS 0,1,2 18 dBm
MCS 3 17 dBm
MCS 4, 5 16 dBm
MCS 6,7 15 dBm
MCS 8,9 14 dBm
MCS 10,11 12 dBm
AP460C, AP460S6C, AP460S12C Hardware Guide
10
AP460C, AP460S6C, AP460S12C Hardware Guide
10

Mode Data Rate Power Unit
2.4 G Sensitivity
11b 1 Mbps -99 dB
11 Mbps -90 dB
11g 6 Mpbs -96 dB
36 Mpbs -84 dB
48 Mbps -80 dB
54 Mbps -78 dB
HE20 MCS 0 -95 dB
MCS 1 -91 dB
MCS 2 -89 dB
MCS 3 -86 dB
MCS 4 -83 dB
MCS 5 -79 dB
MCS 6 -77 dB
MCS 7 -76 dB
MCS 8 -72 dB
MCS 9 -70 dB
MCS 10 -67 dB
MCS 11 -64 dB
5 G:
Tolerance +2/-2 dB @25°C
AP460C, AP460S6C, AP460S12C Hardware Guide
11
AP460C, AP460S6C, AP460S12C Hardware Guide
11

Mode Data Rate Power Unit
11a 54 Mbps 18 dBm
48 Mbps 18 dBm
36 Mbps 19 dBm
6 Mbps 20 dBm
HE20 MCS 0,1,2 20 dBm
MCS 3,4 19 dBm
MCS 5,6 18 dBm
MCS 7,8 17 dBm
MCS 9 16 dBm
MCS 10 15 dBm
MCS 11 14 dBm
HE40 MCS 0,1,2 19 dBm
MCS 3,4,5 18 dBm
MCS 6,7,8 17 dBm
MCS 9 16 dBm
MCS 10 15 dBm
MCS 11 14 dBm
HE80 MCS 0,1,2 19 dBm
MCS 3,4,5 18 dBm
MCS 6,7,8 17 dBm
MCS 9 16 dBm
MCS 10 15 dBm
MCS 11 14 dBm
HE160 MCS 0,1,2 19 dBm
MCS 3,4,5 18 dBm
MCS 6,7,8 17 dBm
MCS 9 16 dBm
MCS 10 15 dBm
MCS 11 14 dBm
5 G Sensitivity
11a 6 Mbps -94 db
36 Mbps -83 db
48 Mbps -79 db
54 Mbps -77 db
HE20 MCS 0 -94 db
MCS 1 -91 db
MCS 2 -88 db
MCS 3 -86 db
AP460C, AP460S6C, AP460S12C Hardware Guide
12
AP460C, AP460S6C, AP460S12C Hardware Guide
12

Mode Data Rate Power Unit
MCS 4 -82 db
MCS 5 -78 db
MCS 6 -77 db
MCS 7 -75 db
MCS 8 -71 db
MCS 9 -69 db
MCS 10 -66 db
MCS 11 -63 db
HE40 MCS 0 -92 db
MCS 1 -88 db
MCS 2 -86 db
MCS 3 -83 db
MCS 4 -80 db
MCS 5 -76 db
MCS 6 -74 db
MCS 7 -73 db
MCS 8 -69 db
MCS 9 -67 db
MCS 10 -63 db
MCS 11 -60 db
HE80 MCS 0 -88 db
MCS 1 -85 db
MCS 2 -83 db
MCS 3 -80 db
MCS 4 -77 db
MCS 5 -73 db
MCS 6 -71 db
MCS 7 -69 db
MCS 8 -66 db
MCS 9 -64 db
MCS 10 -60 db
MCS 11 -57 db
HE160 MCS 0 -85 db
MCS 1 -82 db
MCS 2 -80 db
MCS 3 -77 db
MCS 4 -74 db
MCS 5 -70 db
AP460C, AP460S6C, AP460S12C Hardware Guide
13
AP460C, AP460S6C, AP460S12C Hardware Guide
13

Mode Data Rate Power Unit
MCS 6 -68 db
MCS 7 -66 db
MCS 8 -63 db
MCS 9 -61 db
MCS 10 -57 db
MCS 11 -54 db
Device Specifications
lChassis dimensions when mounted diagonally: 11.375” W 11.375” H 2.9” D (289 mm x 289 mm x 74 mm)
lWeight: 4 pounds (1 .8 kilograms)
lFour dual-band internal WiFi antennas and one BLE internal antenna
lMicro USB Console serial port: (9600 bits per second, 8 data bits, parity: none, 1 stop bit, no flow control
lEth0 Ethernet port: autosensing 10/100/1000Base-T/TX Mbps, with 802.3at-compliant PoE
lEth1 Ethernet port: autosensing 10/100/1000Base-T/TX Mbps
Antennas
AP460C:
l3 integrated single-band 5.1-5.8 GHz omnidirectional antennas
l4 integrated dual band 2.4-2.5 GHz and 5.1-5.8 GHz omnidirectional antennas
l1 integrated single band 2.4-2.5 GHz omnidirectional antenna for BLE
AP460S6C:
l2 Integrated single band, 5.1-5.8 GHz sector antennas
l4 integrated dual band, 2.4-2.5 GHz and 5.1-5.8 GHz sector antennas
l1 integrated single band, 2.4-2.5 GHz omnidirectional antennas for BLE
AP460S12C:
l2 Integrated single band, 5.1-5.8 GHz sector antennas
l4 Integrated dual band, 2.4-2.5 GHz and 5.1-5.8 GHz sector antennas
l1 Integrated single band, 2.4-2.5 GHz omnidirectional antennas for BLE
Antenna Gain
AP460C:
Software Mode 2x2 Rado
WiFi0
4x4 Radio
WiFi1
Scanner
WiFi2 IoT Radio Azimuth Beamwidth Elevation Beam-
width
Dual band 2.4 GHz 3.24 dBi 5 GHz 4.21 dBi 2.4 GHz 3.74 dBi/
5 GHz 3.42 dBi 3.2 dBi 360 150
Dual 5G 5 GHz 3.56 dBi 5 GHz 4.21 dBi 2.4 GHz 3.74 dBi/
5 GHz 3.42 dBi 3,2 dBi 360 150
AP460S6C:
Software
Mode WiFi0 WiFi1 WiFi2 IoT Radio
Azimuth Beam-
width
Elevation Beam-
width
Dual band 2.4 Ghz
7.83dBi
5 Ghz
8.06dBi
2.4 Ghz 7.59dBi/ 5 Ghz
7.63dBi 7.9 dBi 60 60
Dual 5G 5 GHz 3.56 dBi 5 GHz 4.21
dBi
2.4 GHz 3.74 dBi/
5 GHz 3.42 dBi 7.9 dBi 60 60
AP460C, AP460S6C, AP460S12C Hardware Guide
14
AP460C, AP460S6C, AP460S12C Hardware Guide
14

AP460S12C:
Software Mode WiFi0 WiFi1 WiFi2 IoT Radio Azimuth Beamwidth Elevation Beamwidth
Dual band 2.4 GHz 6.46 dBi 5 GHz 6.25
dBi
2.4 GHz 5.53 dBi/
5 GHz 5.54 dBi 6.63 dBi 120 70
Dual 5G 5 GHz 6.34 dBi 5 GHz 6.25
dBi
2.4 GHz 5.53 dBi/
5 GHz 5.54 dBi 6.63 dBi 120 70
Antenna Plots
The antenna plots for the AP460C are available below. The Ethernet port location is noted on each chart.
Antenna 1
Antenna 2
AP460C, AP460S6C, AP460S12C Hardware Guide
15
AP460C, AP460S6C, AP460S12C Hardware Guide
15

Antenna 3
Antenna 4
Antenna 5
AP460C, AP460S6C, AP460S12C Hardware Guide
16
AP460C, AP460S6C, AP460S12C Hardware Guide
16

Antenna 6
Antenna 7
AP460C, AP460S6C, AP460S12C Hardware Guide
17
AP460C, AP460S6C, AP460S12C Hardware Guide
17

Power Specifications
IEEE 802.3af PoE (Power over Ethernet)
Power Options
Power draw w/o USB: typical 19.2 W, maximum 20.8 W
802.3at PoE capable Gigabit Ethernet port (RJ45 power input pins: wires 4, 5, 7, 8 or 1, 2, 3, 6)
802.3af and 802.3at PoE injector
PoE input:
Typical:
l54V DC, 0.40A 21.7W Max. PoE with USB 2.5W (IEEE 802.3at only 42.5-57VDC, USB 0.5A)
l54V DC, 0.45A 19.2W Max. PoE without USB (IEEE 802.3af 37-42.5VDC)
Maximum:
l54V DC, 0.43A 23.3W Max. PoE with USB 2.5W (IEEE 802.3at only 42.5-57VDC, USB 0.5A)
l42.5V DC, 0.49A 20.8W Max. PoE without USB (IEEE 802.3af 37-42.5VDC)
lESD Protection:8 kVcontact discharge / 15 kV air discharge
Power Profile
AP460C 802.3af 802.3at
2.4 G Radio 2x2 (14 dBm) 2x2 (18 dbm)
5 G Radio 2x2 (17 dBm) 4x4 (18 dBm)
Sensor Radio 2.4 G and 5 G (15 dBm) 2.4 G and 5 G
(18 dBm)
BLE Enabled Enabled
USB No Yes
2.5 G Ethernet Yes Yes
1G Ethernet No Yes
Environmental Specifications
AP460C, AP460S6C, AP460S12C Hardware Guide
18
AP460C, AP460S6C, AP460S12C Hardware Guide
18

lOperating temperature: -40° to 140° F (-40° to 60° C)
lStorage temperature: -40° to 158° F (-40° to 70° C)
lRelative Humidity: 0 to 95% RH (noncondensing)
lEnvironmental discharge: +/- 8KVcontact and +/- 15 KV air
lHousing: IP67 rated outdoor use
Regulatory Compliance Statements
The regulatory compliance statements in this section apply to Extreme Networks AP460C devices.
Japan Indoor Use
For Japan, the AP460C is restricted for indoor use in the 5150-5350 MHz band only.
Japan Equipment VCCI-B Statement
Compliance Statement - Europe
EU Declaration of Conformity
View full CE Declaration of Compliance and this information online at www.aerohive.com/support/regulatory-compliance
Extreme Networks, Inc. declares that this device complies with the essential requirements of the Radio Eqiupment Directive 2014/53/EU.
lBulgarian [български]: [Extreme Networks] С настоящото [Extreme Networks] декларира, че този тип радиосъоръжение [AP460C] е в
съответствие с Директива 2014/53/ЕU.
lCroatian [hrvatski]: [Extreme Networks] ovime izjavljuje da je radijska oprema tipa [AP460C] u skladu s Direktivom 2014/53/EU.
lCzech [Česky]: [Extreme Networks] Tímto [jméno výrobce] prohlašuje, že typ rádiového zařízení [AP460C] je v souladu se směrnicí
2014/53/EU.
lDanish [Dansk]: Hermed erklærer [Extreme Networks], at radioudstyrstypen [AP460C] er i overensstemmelse med direktiv 2014/53/EU.
lDutch [Nederland]Hierbij verklaar ik, [Extreme Networks], dat het type radioapparatuur [AP460C] conform is met Richtlijn 2014/53/EU.
lEnglish: Hereby, [Extreme Networks], declares that this [ [[[Undefined variable Primary.AP640]]]] is in compliance with the essential require-
ments and other relevant provisions of Directive 2014/53/EU.
lEstonian [Eesti]: Käesolevaga deklareerib [Extreme Networks], et käesolev raadioseadme tüüp [AP460C] vastab direktiivi 2014/53/EL
nõuetele.
lFinnish [Suomi]: [Extreme Networks] vakuuttaa, että radiolaitetyyppi [AP460C] on direktiivin 2014/53/EU mukainen..
lFrench [Français]: Le soussigné, [Extreme Networks], déclare que l'équipement radioélectrique du type [AP460C] est conforme à la directive
2014/53/UE.
lGerman [Deutsch]: Hiermit erklärt [Extreme Networks], dass der Funkanlagentyp [AP460C] der Richtlinie 2014/53/EU entspricht.
lGreek [Ελληνική]: ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [Extreme Networks] ΔΗΛΩΝΕΙ ΟΤΙ[ AP460C] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣΤΙΣ ΟΥΣΙΩΔΕΙΣΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ
ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 2014/53/EU.
lHungarian [Magyar]: [Extreme Networks] igazolja, hogy a [AP460C] típusúrádióberendezés megfelel a 2014/53/EU irányelvnek.
lItalian [Italiano]: Il fabbricante, [Extreme Networks], dichiara che il tipo di apparecchiatura radio [AP460C] è conforme alladirettiva
2014/53/UE.
lLatvian [Latviski]: Ar šo [Extreme Networkss] deklarē, ka radioiekārta [AP460C] atbilst Direktīvai 2014/53/ES.
lLithuanian [Lietuvių]: Aš, [Extreme Networks], patvirtinu, kad radijo įrenginių tipas [AP460Cs] atitinka Direktyvą 2014/53/ES.
lMaltese [Malti]: B'dan, [Extreme Networks], niddikjara li dan it-tip ta' tagħmir tar-radju [AP460C] huwa konformi mad-Direttiva 2014/53/UE.
lPolish [Polski]: [Extreme Networks] niniejszym oświadcza, że typ urządzenia radiowego [AP460C] jest zgodny z dyrektywą 2014/53/UE.
AP460C, AP460S6C, AP460S12C Hardware Guide
19
AP460C, AP460S6C, AP460S12C Hardware Guide
19

lPortuguese [Português]: O(a) abaixo assinado(a) [Extreme Networks] declara que o presente tipo de equipamento de rádio [AP460C] está
em conformidade com a Diretiva 2014/53/UE.
lRomanian [Romania]: Prin prezenta, [Extreme Networks] declară că tipul de echipamente radio [AP460C] este în conformitate cu Directiva
2014/53/UE.
lSlovak [Slovensky]: [Extreme Networks] týmto vyhlasuje, že rádiové zariadenie typu[AP460C] je v súlade so smernicou 2014/53/EÚ.
lSlovenian [Slovenija]: [Extreme Networks] potrjuje, da je tip radijske opreme [AP460C] skladen z Direktivo 2014/53/EU.
lSpanish [Español]: Por la presente, [Extreme Networks] declara que el tipo de equipo radioeléctrico [AP460C] es conforme con la Directiva
2014/53/UE.
lSwedish [Sverige]: Härmed försäkrar [Extreme Networks] att denna typ av radioutrustning [AP460C] överensstämmer med direktiv
2014/53/EU.
Radio Specifications
Bluetooth BLE Beacon
l2402 - 2480 MHz
lFrequency Hopping Spread-Spectrum (FHSS)
USA, Canada, and Taiwan Radio Frequency Bands
a. USA
l802.11b/g/n/ac: 2.4 GHz band: 2400-2483 MHz
l802.11a/n/ac/ax: 5 GHz band: 5150-5350, 5470-5850 MHz
lBLE: 2402-2480 MHz
b. Canada
l802.11b/g/n/ac: 2.4 GHz band: 2400-2483 MHz
lIndoor: 802.11a/n/ac/ax: 5 GHz band: 5150-5350, 5470-5600, 5650-5850 MHz
ll Outdoor: 802.11a/n/ac/ax: 5 GHz band: 5250-5350, 5470-5600, 5650-5850 MHz
lBLE: 2402-2480 MHz
c. Taiwan
ll 802.11b/g/n/ac: 2.4 GHz band: 2412-2462 MHz
ll 802.11a/n/ac/ax: 5 GHz band: 5180-5320, 5500-5825 MHz
ll BLE: 2412-2462 MHz
EURadio Frequency and Power Levels
This product supports the following radio frequencies and power levels in the EUversion:
l802.11b/g/n/ac, 2.4 GHz band: 2400-2483 MHz EIRP<20 dBm
l802.11a/ac/n/ax: 5 GHz band: 5150-5350 MHz EIRP<23 dBm (indoor only), 5470-5850 MHz EIRP<30 dBm, 5725-5850 MHz<14 dBm
lBLE: 2402-2480 MHz EIRP<8 dBm
Bulgarian [български]: Този продукт поддържа следните радиочестоти и нива на мощност във версията на ЕС:
l802.11b/g/n/ac, 2.4 GHz band: 2400-2483 MHz EIRP<20 dBm
l802.11a/ac/n/ax: 5 GHz band: 5150-5350 MHz EIRP<23 dBm (indoor only), 5470-5850 MHz EIRP<30 dBm, 5725-5850 MHz<14 dBm
lBLE: 2402-2480 MHz EIRP<8 dBm
Croatian [hrvatski]: Ovaj proizvod podržava sljedeće radijske frekvencije i razinu snage u verziji EU:
l802.11b/g/n/ac, 2.4 GHz band: 2400-2483 MHz EIRP<20 dBm
l802.11a/ac/n/ax: 5 GHz band: 5150-5350 MHz EIRP<23 dBm, 5470-5850 MHz EIRP<30 dBm, 5725-5850 MHz<14 dBm
lBLE: 2402-2480 MHz EIRP<8 dBm
Česky [Czech]: [Tento produkt podporuje následující rádiové frekvence a úrovně výkonu ve verzi EU:
l802.11b/g/n/ac, 2.4 GHz band: 2400-2483 MHz EIRP<20 dBm
l802.11a/ac/n/ax: 5 GHz band: 5150-5350 MHz EIRP<23 dBm, 5470-5850 MHz EIRP<30 dBm, 5725-5850 MHz<14 dBm
lBLE: 2402-2480 MHz EIRP<8 dBm
Danish [Dansk]: Dette produkt understøtter følgende radiofrekvenser og strømniveauer i EU-versionen:
AP460C, AP460S6C, AP460S12C Hardware Guide
20
AP460C, AP460S6C, AP460S12C Hardware Guide
20