EZ-ACCESS PATHWAY 3G SS28 User manual

Manufactured in the USA
LIFETIME WARRANTY. Please register at www.ezaccess.com/warranty-satisfaction.
© EZ-ACCESS®, a division of Homecare Products, Inc. All rights reserved.
All text and images contained in this document are proprietary and may not be shared, modified, distributed,
reproduced, or reused without the express written permission of EZ-ACCESS.
16397 REV 01-25-18
PATHWAY®3G
Modular Access System
Assembly Manual
Image shown with multiple ramp and
platform handrail options.

Page 2 of 74
PATHWAY®3G
Modular Access System
Assembly Manual
ATTENTION INSTALLER and END USER
•For residential use only!
•1,000 Lb. weight capacity.
•Read this manual in its entirety, ensuring you understand all instructions and warnings prior to ramp
assembly and use.
•INSTALLER: Please leave this ASSEMBLY MANUAL with the end user.
•Please read and become familiar with the ‘MAINTENANCE AND SAFETY’ section of this manual.
•Fill out online warranty registration.
TOOLS TYPICALLY REQUIRED
1/2″ SOCKET OR 1/2″ WRENCH
9/16″ SOCKET OR 9/16″ WRENCH
5/16″ SOCKET OR 5/16″ WRENCH
LEVEL
FILE
RUBBER MALLET
POWER DRILL
25’ TAPE MEASURE
#2 PHILLIPS HEAD SCREW DRIVER PLIERS
5/16″ DRILL BIT (IF BRACE ASSEMBLIES ARE
USED)
5/32″ ALLEN WRENCH (INCLUDED)
3/16″ ALLEN WRENCH (INCLUDED)
BOX KNIFE
HAMMER
1/4″ MASONRY DRILL BIT (USED WHEN
INSTALLING TO CONCRETE PORCH, STEP, ETC.)
DIGGING TOOLS (IF AN OBSTACLE NEEDS TO BE
REMOVED)
HACKSAW (FOR OPTIONAL HANDRAIL KITS)
VIEW PACKING LIST
Each ramp system is shipped with a packing list. Be sure to check that all items and tools are present before
starting installation.
SYMBOL MEANINGS
The WARNING symbol indicates a potentially hazardous condition/situation. The safety warnings
throughout this manual, and on your equipment, if any, are for the protection of people and
property. Failure by any operator to abide by safety warnings will result in a waiver of all liabilities,
loss of your warranty, and could result in equipment damage and or failure, property damage, risk of
serious bodily injury, and or death. The symbol may appear in various colors and in conjunction with
other symbols and with or without the written word “WARNING”.
The NOTE symbol indicates important information. Failure to obey all notes could result in improper
operation, less-than-optimum equipment performance, and at the sole discretion of the equipment
manufacturer, may void your warranty. The symbol may appear in various colors and in conjunction
with other symbols and with or without the written word “NOTE”.

Page 3 of 74
PROPER SET UP AND USE WARNINGS
Read and follow all labels, instructions, and warnings prior to assembly and use. To obtain a copy of
complete instructions and warnings, call customer service at 1-800-451-1903.
Use caution at all times. Proper maintenance and upkeep to the PATHWAY® 3G Modular Access
System and all PATHWAY® system components is vital.
The term “system” refers to the entire PATHWAY 3G Modular Access System, including any gates,
stairs, ramps, platforms, risers, handrails, supports, transition plates, landing pads, and any/all
hardware and components which are intended to be assembled on the PATHWAY 3G Modular Access
System.
Regularly check that all parts are in good condition and check the system for damage. Ensure all
fasteners and locking mechanisms are in place and tightened. If any part of the system is damaged,
loose, or missing, DO NOT USE until system repairs can be made by a certified installer or other
qualified person.
Do not walk, sit, stand, etc. on the system until the installation is complete.
Consult local building codes regarding securing system for wind loads.
Use system only with a qualified helper.
Keep the system clear of debris and clutter. Do not use if walking surface is unsafe.
Confirm the system is correctly leveled and positioned securely. Periodically check for ground shifts.
Metal conducts electricity. Do not use near exposed wiring or hang lights from system.
Never place anything on, under, or attach anything to system.
Only use components supplied or approved by manufacturer with system.
Do not sit, stand, or climb on guards, gates, or handrails.
Do not use handrails, gates, or any other part of the system, to support planters, decorations, etc.
Do not play on or around system, including, but not limited to, running, jumping, bicycles, scooters,
skateboards, etc.
Properly support and restrain system in transit or storage.
At all times, keep the system clear of dirt, leaves, and other debris that may accumulate on the
surface. Simply sweeping the system or using a garden hose will usually suffice, but, if needed, a
damp cloth or soft brush with soap and water can be used (avoid alkaloid detergents). Rinse well and
use extra caution when system surface is wet.
The system may be slippery when wet or icy.
If system surface is covered with ice and/or snow, DO NOT USE until accumulation is removed and
the tread surface swept clean. Please refer to ‘DEICING SECTION’ of this for more information.
Regularly check that all parts are in good condition and check the system for damage. Ensure all
fasteners and locking mechanisms are in place and tightened. If any part of the system is damaged,
loose, missing, or unstable DO NOT USE until repairs can be made by a certified installer or other
qualified person.
For additional care, usage, or general safety information, please call 1-800-451-1903.

Page 4 of 74
TABLE OF CONTENTS
SECTION 1: BASIC SYSTEM COMPONENTS
IDENTIFYING COMPONENTS ......................................................................................................................... 5-11
SECTION 2: PLATFORMS
INSTALL PLATFORMS.........................................................................................................................................12
INSTALL SUPPORT TUBES AND FEET AND ADJUST PLATFORM HEIGHT...................................................... 13-14
CONNECT TWO PLATFORMS TOGETHER .................................................................................................... 14-15
PLATFORM RAMP TO RAMP 45° ANGLE ...........................................................................................................16
8’ X 5’ TURN BACK PLATFORM ..........................................................................................................................16
INSTALL UNIVERSAL ANGLE BRACE - PLATFORMS ............................................................................................17
INSTALL UNIVERSAL CROSS BRACE ...................................................................................................................17
SECTION 3: RAMPS
CONNECT RAMP SECTIONS ...............................................................................................................................18
INSTALL RAMPS ON PLATFORMS ......................................................................................................................19
ATTACH RAMP LEGS TO RAMPS:................................................................................................................. 20-22
INSTALL UNIVERSAL ANGLE BRACE - RAMPS ....................................................................................................22
INSTALL GROUND TRANSITION RAMP ..............................................................................................................23
INSTALL A SINGLE RAMP RUN TO AN EXISTING STRUCTURE ............................................................................24
ANCHOR RAMP UPPER TRANSITION.................................................................................................................25
ANGLE RAMPS WITH RESPECT TO PLATFORMS, PORCHES, OR DECKS .............................................................26
SECTION 4: HANDRAILS
RAMP WITHOUT HANDRAILS ............................................................................................................................27
RAMP HANDRAILS ....................................................................................................................................... 27-28
FIELD CONVERT TWO-LINE RAMP HANDRAILS TO VERTICAL PICKETS .............................................................29
ASSEMBLE HORIZONTAL PICKET RAMP HANDRAILS ........................................................................................30
ASSEMBLE STANDARD PLATFORM HANDRAILS .......................................................................................... 31-32
INSTALL STANDARD PLATFORM HANDRAILS .............................................................................................. 33-34
CONVERT TWO-LINE PLATFORM HANDRAILS TO OTHER STYLES .....................................................................34
8’ X 5’ TURN BACK PLATFORM HANDRAILS (OPTIONAL EQUIPMENT) ....................................................... 34-36
45° ANGLE PLATFORM HANDRAILS (OPTIONAL EQUIPMENT).................................................................... 37-43
SECTION 5: CLOSURES
SINGLE-LINE CLOSURE AND TOP RAIL ......................................................................................................... 44-47
TWO-LINE CLOSURE LOWER RAIL .....................................................................................................................48
VERTICAL PICKET CLOSURE ......................................................................................................................... 49-50
HORIZONTAL PICKET CLOSURE ................................................................................................................... 51-52
TURN BACK CLOSURES ................................................................................................................................ 53-55
SECTION 6: FINAL PLATFORM/RAMP STEPS AND CHECKS
SECURE RAMPS TO PLATFORMS .......................................................................................................................56
INSTALL RAMP HANDRAIL END LOOPS ....................................................................................................... 57-58
INSTALL RAMP HANDRAIL END CAPS................................................................................................................58
INSTALL RAMP CORNER PROTECTORS ..............................................................................................................59
TOUCH-UP ARCHITECTURALLY FINISHED HANDRAILS ......................................................................................59
FINAL CHECKS....................................................................................................................................................59
SECTION 7: OPTIONAL EQUIPMENT
RAMP SUPPORT – TOP ......................................................................................................................................60
RAMP LOWER TRANSITION ...............................................................................................................................61
SINGLE BRIDGE PLATE .......................................................................................................................................61
LANDING PAD.............................................................................................................................................. 62-63
PLATFORM TIE STRAPS......................................................................................................................................64
LIGHTNING GROUND ROD ................................................................................................................................65
TIE DOWN ................................................................................................................................................... 66-68
GATE............................................................................................................................................................ 69-70
SECTION 8: MAINTENANCE & SAFETY
PERIODIC MAINTENANCE & SAFETY .................................................................................................................71
SECTION 9: DE-ICING NOTES ...................................................................................................................................72

Page 5 of 74
1. BASIC SYSTEM COMPONENTS
Because each ramp configuration will differ from one another, your system may or may not contain all
these basic system components. Identify your system components before you begin. Check which surface
option and handrail options are included.
SURFACE OPTIONS
SOLID SURFACE EXPANDED METAL SURFACE PERFORATED SURFACE
RAMPS AND RAMP HANDRAIL OPTIONS
RAMP WITHOUT HANDRAILS RAMP* WITH SINGLE-LINE HANDRAIL
RAMP WITH TWO-LINE HANDRAIL RAMP* WITH VERTICAL PICKETS RAMP* WITH HORIZONTAL PICKETS
*RAMP OR PLATFORM NOT INCLUDED

Page 6 of 74
KEY RAMP COMPONENTS
PRLXXPR – RAMP LEG PAIRS PRGT & PRGT48
RAMP GROUND TRANSITION 18” X 36”and 18” X 48”
PRHBPR – RAMP HANDRAIL END BRACKET (PAIR) PRRC – CONNECTOR – RAMP TO RAMP
PRST - RAMP SUPPORT TOP PRHP - RAMP HANGER PAIR
XX DENOTES USABLE
LENGTH (LENGTHS
AVAILABLE 10”
THROUGH 100" IN 6”
INCREMENTS)
INCLUDES
COMPONENTS TO
CONNECT RAMPS
AND RAMP
HANDRAILS
SHOWN ASSEMBLED
USED WHEN LEGS
SUPPORT UPPER OR
LOWER END OF RAMP
ONLY

Page 7 of 74
KEY RAMP COMPONENTS, CONT’D.
PRHRLU
-
UPPER HANDRAIL END LOOP
PRHRLL - LOWER HANDRAIL END
LOOP
PHREC - HANDRAIL END CAP
PRUT – RAMP UPPER TRANSITION PRLT – RAMP LOWER TRANSITION
INCLUDES RAMP
CORNER PROTECTORS
WITH THE
UPPER
END
LOOP, THE TUBE
WITH
ATTACHMENT
PLATE IS LONGER
THA
N ON THE
LOWER
END
LOOP
WITH THE
LOWER
END
LOOP, THE TUBE
WITH
ATTACHMENT
PLATE IS
SHORTER
THAN
ON THE UPPER
END LOOP

Page 8 of 74
PLATFORMS AND PLATFORM HANDRAIL OPTIONS
PLATFORM (STRAIGHT CONFIGURATION) PLATFORM (TURN CONFIGURATION)
PLATFORM (8’ X 5’ TURN BACK) PLATFORM* WITH SINGLE-LINE HANDRAIL
PLATFORM* WITH VERTICAL PICKET HANDRAIL PLATFORM* WITH HORIZONTAL PICKET HANDRAIL
*RAMP OR PLATFORM NOT INCLUDED

Page 9 of 74
PLATFORMS AND PLATFORM HANDRAIL OPTIONS, CONT’D.
PLATFORM (45° ANGLE W/ TWO-LINE HANDRAILS) PLATFORM (45° ANGLE W/VERTICAL PICKETS)
45° Angle Platform not available with SINGLE-LINE or HORIZONTAL PICKET handrails
KEY PLATFORM COMPONENTS
PSTSXXPR – PLATFORM FEET & SUPPORT TUBE PAIRS PPPC – CONNECTOR – PLATFORM TO PLATFORM
PBP36, PBP48, PBP60 – BRIDGE PLATE PPTS – PLATFORM TIE STRAP
XX DENOTES
USABLE LENGTH
(LENGTHS
AVAILABLE 10”
THROUGH 100")

Page 10 of 74
CLOSURE OPTIONS
PPCSL – SINGLE-LINE CLOSURE HANDRAIL PPCTL – TWO-LINE CLOSURE HANDRAIL
PPCVP4, PPCVP5, PPCVP5
VERTICAL PICKET CLOSURE HANDRAIL PPCHP – HORIZONTAL PICKET CLOSURE HANDRAIL

Page 11 of 74
ADDITIONAL OPTIONS
PTDK – TIE DOWN KIT PUAB – ANGLE BRACE PUCB4, PUCB5 & PUCB8 – UNIVERSAL CROSS BRACE
PLP – LANDING PAD PUG36 – PATHWAY 3G GATE 36”
•PUCB4 USED
ON 4’
PLATFORM
SIDE
•PUCB5 USED
ON 5’ & 6’
PLATFORM
SIDES
•PUCB8 USED
ON 8’
PLATFORM
SIDE

Page 12 of 74
2. PLATFORMS
2.1. INSTALL PLATFORMS
If your system does not include a platform, skip to ‘CONNECT RAMP SECTIONS’.
Platform handrails are shown for clarity of how to orient platforms in various
configurations. It is strongly suggested that all platforms and ramps be installed before
installing handrails (see ‘HANDRAILS’ section).
2.1.1. There are four basic platform arrangements (one or more of these platform
arrangements may be used in an installation). All four require the same procedure for
assembly except for FIG.2.3 which requires an additional PPPC (PLATFORM TO
PLATFORM CONNECTOR).
FIG. 2.1 Platform in straight configuration.
FIG. 2.2 Platform in turn configuration.
FIG. 2.3 Platforms in turn back configuration (two 5' x 4' platforms
shown combined to make 5' x 8’ turn back).
FIG. 2.48’ x 5’ turn back platform.
FIG. 2.1
FIG. 2.2
FIG. 2.3
FIG. 2.4

Page 13 of 74
2.2. INSTALL SUPPORT TUBES AND FEET, THEN ADJUST PLATFORM HEIGHT
2.2.1. Support tubes, plugs, and feet come in pairs. Support tubes will come in lengths
sufficient for the heights at specific locations.
2.2.2. Loosen all set screws in the platform corner pockets.
2.2.2.1 The set screws on the outside of the platform are for the platform support
tubes.
2.2.2.2. The set screws on the inside of the platform (one above the deck and one
below the deck) are for the handrail posts.
2.2.3. Tip the platform on its side, then slide the support tubes into the four platform corner
pockets. Adjust the support tubes to the approximate platform height needed (FIG.2.5).
FIG. 2.5
2.2.4. Use supplied 3/16″Allen wrench to tighten the upper of the two set screws in the
corner pocket, just enough to hold the support tube in place but do not over tighten
(the second set screw will be tightened after final height adjustments are complete).
Platforms configured as a turn back platform (FIG. 2.3) will have six tubes to
adjust.
Do not attempt to walk on the platform until all support tube set screws have
been tightened securely.
2.2.5. Place the platform (with support tubes attached) into the upright position.
Do not let the weight of the platform bear on the support tubes while tipping
the platform upright.
2.2.6. Lift each corner of the platform and install a base foot on each support tube oriented
so that the foot extends under the platform (FIG. 2.5).

Page 14 of 74
The feet can be oriented in other directions if necessary due to site conditions
but may present a tripping hazard if not oriented under the platform.
It is the installer’s responsibility to install the system in a manner which is safe
for the persons on and around the system and clearly mark any hazards created
by the installation.
2.2.7. Make sure the feet are fully engaged on the tubes and tighten the thumb screw on
each foot securely.
If installing on soft soil it may be necessary to set the base foot on a concrete
pad.
2.2.8. Adjust the final height of the platform by adjusting legs, one at a time, by loosening the
outer set screws in the platform corner pockets. Using a level, adjust the platform
height and re-tighten.
2.2.9. Once the final height has been adjusted, tighten the second, lower set screw in each
platform corner pocket.
2.2.10. To allow access to the lowermost hole in the platform post, the support tubes must not
extend more than 1/2” above the platform corner pockets. Trim the support tubes as
needed before installing plugs.
2.2.11. Insert a plug into the top of each support tubes. Use a rubber mallet or similar tool as
needed (FIG.2.5).
2.2.12. Ensure all set screws are tightened securely.
2.3. CONNECT TWO PLATFORMS TOGETHER
2.3.1. Assemble the first platform as described in the previous steps except on the side where
the second platform will connect, install two PPPC (CONNECTOR – PLATFORM TO
PLATFORM) before installing feet onto the support tubes.
2.3.2. Make sure the platform connector set screws are oriented outward so they will be
accessible.
Any two platforms of the same width can be connected. However, two 5' x 4’
platforms are usually connected to make a turn back platform.
2.3.3. Slide the platform connectors up until they contact the bottom of the platform and
tighten the set screws securely (FIG. 2.6).
2.3.4. Install a support tube stub into the open pocket in each connector until the bottom of
the stub is flush with the bottom of the connector and tighten the set screws securely.
2.3.5. Install a plug in the top of each support tube stub.
2.3.6. Assemble the second platform as described in the previous section except only install
support tubes, plugs, and feet on the opposite side of where the platforms will connect
(FIG. 2.7).
2.3.7. Lift the second platform and slide the open corner pockets over the support tube stubs
extending up from the platform connectors. Tighten the set screws in the platform
corner pockets securely.
2.3.8. Adjust the platform heights and level as needed.
Make sure all the set screws in both the platform corner pockets and the
platform connectors are tightened securely before proceeding with the
installation.

Page 15 of 74
FIG. 2.6
FIG. 2.7

Page 16 of 74
2.4. 45°ANGLE PLATFORM
This platform is used between two ramps to make a 45-degree turn and features a symmetrical
design, making it usable in either direction.
2.4.1. There are two options for 45° Angle Platform handrails, Two-Line and Vertical Pickets.
The platform includes the handrail components needed for the option ordered.
Platform handrails are shown for clarity of how to orient platforms in various
configurations. It is strongly suggested that all platforms and ramps be installed
before installing handrails (see ‘HANDRAILS’ section).
2.4.2. Set platform on one of the sides where the ramp will attach and install legs and feet
and adjust height as described previously in this section. The two legs on the short
side must be installed in the orientation shown (FIG. 2.8)
Use “low profile foot for platform heights under 4”.
It is sometimes helpful to lay platform on its side when inserting the legs.
FIG. 2.8
2.4.3. Install ramps on both sides of the platform where there are no curbs. Refer to Section
3.2 for installing ramps on platforms and Section 4 for installing ramp handrails.
2.5. 8’ X 5’ TURN BACK PLATFORM
This platform is used to create a turn back (or switchback) instead of connecting two 5’ x 4’
platforms. It includes two standard 5’ platform handrails and handrails for the 8’ side with a curb.
2.5.1. Install the support tubes and feet as described in the ‘INSTALL SUPPORT TUBES AND
FEET, THEN ADJUST PLATFORM HEIGHT’ section.

Page 17 of 74
2.6. INSTALL UNIVERSAL ANGLE BRACE - PLATFORMS
For added stability, any platform with a walking surface over 36″high requires bracing. The PUAB
(PATHWAY ANGLE BRACE) is used for surfaces 36″up to 72″. Walking surfaces 72″and higher
requires cross braces in addition to the angle braces.
2.6.1. Angle braces come in pairs. Use four pairs per platform (one pair per support tube, or
side) or six pairs when two platforms are connected.
2.6.2. Use two brace bands to secure the ends of the two angle braces nearest the twist to
the support tube using a 5/16" bolt, flat washer, and nut (FIG. 2.9).
2.6.3. Opposite ends of the braces are attached to the bottom of the platform side rail at
90° to each other using a 1/4″x 1” long self-drilling screw (FIG. 2.9).
FIG. 2.9
2.7. INSTALL UNIVERSAL CROSS BRACE
2.7.1. Install UNIVERSAL CROSS BRACES on all support tubes when the walking surface is
72″or more above the ground. Cross braces are normally installed on all four sides
(FIG. 2.10) unless two platforms are connected.
2.7.2. Ensure that all cross braces are secured before using platform.
FIG. 2.10

Page 18 of 74
3. RAMPS
3.1. CONNECT RAMP SECTIONS
3.1.1. Place the walking surface side of the ramp sections face down, onto cardboard or
lawn so that the ramp is not damaged (scratched or dented).
When installing a single ramp section, skip to 'INSTALL A SINGLE RAMP RUN TO
AN EXISTING STRUCTURE’.
3.1.2. Butt the sections together end-to-end and ensure there is no gap, then position the
two center saddle brackets, included in the PRRC (CONNECTOR – RAMP TO RAMP),
over the threaded inserts at the end of each ramp section (FIG. 3.1).
3.1.3. One edge of the center saddle bracket will slide into the groove of the ramp sections.
To create a run, ramp sections are connected using two interchangeable center
saddle brackets per joint. The center saddle brackets are also where the
handrails and ramp legs are attached.
FIG. 3.1
(BOTTOM VIEW)
FIG 3.2
(BOTTOM VIEW)
3.1.4. Attach the center saddle brackets using four each 5/16″-18 x 1-1/2″bolts and 5/16″
washers per bracket. Tighten all eight bolts (four each per center saddle bracket).
Although a system can have multiple ramps per run, it is recommended that a
maximum of three ramp sections at a time be joined in this manner.
3.1.5. If necessary, install optional PRST (RAMP SUPPORT – TOP) at this time (see
‘OPTIONAL EQUIPMENT’ section).
3.1.6. Locate PRHBPR (RAMP HANDRAIL END BRACKET PAIR). Install four end brackets
(these will be used to attach handrails in a later step). Use one end bracket at each
outside corner of the ramp or ramp run using one 5/16″ x 1-1/2″ bolt and washer
into the threaded insert closest to the end of the ramp (FIG. 3.2).
3.1.7. Turn the joined ramps to their upright position, being careful not to damage the
threaded studs.

Page 19 of 74
3.2. INSTALL RAMPS ON PLATFORMS
3.2.1. The following will address attaching a ramp or ramp run to a platform. If the ramp
needs to be angled with respect to the platform or is going to be attached to an
existing porch, skip to ‘ANGLE RAMPS WITH RESPECT TO PLATFORMS, PORCHES, OR
DECKS’ in this section.
3.2.2. Ramps are most commonly located toward either the left or right side of the platform
or centered but can be placed in any location on a platform side except when using a
‘VERTICAL PICKET CLOSURE’ (outlined in SECTION 5). When the ramp is located
toward the side of a platform, the ramp handrail post should be positioned 1-1/2”
(minimum) to 2” from the inside of the platform post. When using other locations, a
second closure (Single-Line, Two-Line or Horizontal Picket) must be ordered to
connect the ramp and platform handrails. When centering ramps using a Vertical
Picket Closure additional components are needed. The additional components will
come with the closure if specified at the time of order. The closure can also be
converted in the field by ordering a second set of hardware.
3.2.3. Locate a PRHP (RAMP HANGER PAIR) and install the two hangers in the platform side
rail where the ramp will be attached.
3.2.4. Hold the hanger perpendicular (approximately) to the platform side rail then bring
the hanger upward until it is against the side rail lip. Rotate the hanger and continue
pushing upward in such a manner that the “hook″at the top of the hanger goes
behind and catches on the lip in the top of the platform side rail and the hanger sits
on the ledge at the bottom (FIG. 3.3).
3.2.5. Set the ramp on the hangers. The hangers should be positioned as close as possible
to the ramp side rails. The procedure is the same at both the top and bottom of ramp
runs which end at a platform unless a transition plate is used (FIG. 3.4).
Do not attempt to walk on ramps until installation is complete.
FIG. 3.3
(TOP VIEW)
FIG. 3.4
(BOTTOM VIEW)

Page 20 of 74
3.3. ATTACH RAMP LEGS TO RAMPS
3.3.1. Locate the appropriate PRLxxPR (RAMP LEG PAIR where “xx” denotes the leg length)
for the location. Insert the leg into a foot. Make sure the leg is fully engaged in the
foot and the foot will be oriented so it extends under the ramp once installed.
Tighten the thumb screw on each foot securely (FIG. 3.5).
If installing on soft soil it may be necessary to set the foot on a concrete pad.
FIG. 3.5
3.3.2. Place the slot in the ramp leg over the two shorter studs in the middle of the center
saddle bracket, install the support plate over both studs then install 5/16”-18 nylon
insert locknuts and 5/16” flat washers on each stud but do not tighten fully. Repeat
on the opposite side (FIG 3.5)
In situations where the lower end of a ramp or ramp run is too close to the
ground to install normal feet and feet are needed due to ground or other
conditions, special welded low profile feet (part no. PRLPRLP). are available (FIG
3.6).
3.3.3. Remove the 5/16”-18 nylon insert locknuts and 5/16” flat washers attaching the
ramp handrail post (if already installed), position the low profile foot so the foot is
oriented under the ramp and the channel leg wraps around the ramp post. Reinstall
the locknuts and flat washers, adjust height as described below then tighten
fasteners securely. Repeat on the opposite side (FIG. 3.6).