EZ-ACCESS PATHWAY User manual

Manufactured in the USA
LIFETIME WARRANTY. Please register at www.ezaccess.com/warranty-satisfaction.
© EZ-ACCESS®, a division of Homecare Products, Inc. All rights reserved.
All text and images contained in this document are proprietary and may not be shared, modified, distributed,
reproduced, or reused without the express written permission of EZ-ACCESS.
21123 REV 09-19-2022
Assembly Manual
PATHWAY®Aluminum Wheelchair Ramp Kit
Configuration shown with straight ramp run and 4’x 4’top platform.
However, there are multiple configurations and sizes
available. See inside manual for additional information.

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 2 of 39
1
ATTENTION INSTALLER and END USER
•For residential use only!
•Maximum weight capacity is 1,000 lbs.; never exceed weight capacity.
•Read this manual in its entirety, ensuring you understand all instructions and warnings prior to ramp
assembly and use.
•Please read and become familiar with the ‘MAINTENANCE AND SAFETY’ section of this manual.
•Fill out online warranty registration.
IMPORTANT SHIPPING INFORMATION
•Immediately inspect for damage or missing parts. If damaged or missing parts are noted, DO NOT INSTALL
OR USE.
•Each system is shipped with a packing list. Confirm all items are present before starting installation. Also
check for shipping damage immediately upon receipt and note any freight damage on freight bill while driver
is still present. Contact shipper right away with any freight damage concerns. In most cases, freight damage
claims will not be allowed unless noted on the freight bill. Pictures of damage before the unit is unpacked
can be very helpful.
TOOLS TYPICALLY REQUIRED
✓1/2″ SOCKET OR 1/2″ WRENCH
✓BOX KNIFE
✓9/16″ SOCKET OR 9/16″ WRENCH
✓HAMMER
✓5/16″ SOCKET OR 5/16″ WRENCH
✓LEVEL
✓POWER DRILL
✓FILE
✓#2 PHILLIPS SCREW DRIVE
✓RUBBER MALLET
✓PLIERS
✓1/4″ MASONRY DRILL BIT (IF INSTALLING TO CONCRETE)
✓1/8” DRILL BIT
✓DIGGING TOOLS (IF AN OBSTACLE NEEDS TO BE REMOVED)
✓5/16″ DRILL BIT
✓HACKSAW
✓5/32″ ALLEN WRENCH
✓25’ TAPE MEASURE
✓3/16″ ALLEN WRENCH
✓CONSTRUCTION ADHESIVE

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 3 of 39
1
INTRODUCTION
Throughout this manual, the term “system” refers to the entire PATHWAY® Aluminum Wheelchair Ramp Kit,
including all components and hardware which are intended to be assembled on the PATHWAY Aluminum
Wheelchair Ramp Kit.
SYMBOLS
The WARNING symbol indicates a potentially hazardous condition/situation. The safety warnings
throughout this manual, and on your equipment, if any, are for the protection of people and property.
Failure by any operator to abide by safety warnings will result in a waiver of all liabilities, loss of your
warranty, and could result in equipment damage and or failure, property damage, risk of serious bodily
injury, and or death. The symbol may appear in various colors and in conjunction with other symbols
and with or without the written word “WARNING”.
The NOTE symbol indicates important information. Failure to obey all notes could result in improper
operation, less-than-optimum equipment performance, and at the sole discretion of the equipment
manufacturer, may void your warranty. The symbol may appear in various colors and in conjunction
with other symbols and with or without the written word “NOTE”.
WARNINGS
Maximum weight capacity is 1,000 lbs.; never exceed weight capacity.
Prior to assembly and use, read and follow all instructions, warnings, and labels. Following all
instructions and obeying all warnings before and during use is necessary for safe operation. For
additional information or to obtain replacement copies of instructions or labels, call 1-800-451-1903.
For people and mobility equipment only; not for commercial use.
Consult local building codes regarding securing the system for wind loads.
Before use with mobility equipment, refer to your mobility equipment's owner guide for acceptable
ramp usage, including proper slope/incline, chair direction, etc.; never exceed its recommendations.
Only use the system with a qualified helper.
Always use a lap belt if using the system with mobility equipment.
If walking on the system, handrails are required and must be installed.
Before each use, check the system for worn, loose, or damaged parts. If you find any of these
conditions, do not use the system and contact your dealer for service or repairs; failure to do so may
result in serious injury.
Do not use the system if it is damaged or unstable.
Do not tamper with, attempt to repair, or modify any portion of the system.
Ensure that the landings the system will be placed on are substantial and of sound construction.
Use only if the secure, unobstructed, level landings can support, at minimum, the same weight capacity
as the system (1,000 lbs.).
Ensure that the system is securely anchored before each use.
Use only if sufficient maneuvering room is available at both ends of the system to assure safe travel
when entering and exiting the system.
Do not walk, sit, stand, etc. on the system until the installation is complete.
Consult local building codes regarding securing system for wind loads.
Keep the system clear of debris and clutter. Do not use if walking surface is unsafe.
Confirm the system is correctly leveled and positioned securely. Periodically check for ground shifts.
Never place anything on, under, or attach anything to system.
Only use components supplied or approved by manufacturer with system.
Do not sit, stand, or climb on guards, gates, or handrails.
Do not use any part of the system to support planters, lights, decorations, etc.

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 4 of 39
1
WARNINGS, CONT’D.
Do not run, jump, or play on or around the system, including climbing on or between the handrails.
Improper use of the system could result in serious injury.
Properly support and restrain system in transit or storage.
Do not use the system if its surface is covered with ice, snow, dirt, leaves, or other debris. Remove all
accumulations and sweep the surface clean before use.
The system may be slippery in wet conditions; use caution as traction may be reduced.
Before each use, check the system for worn, loose, or damaged parts. If you find any of these
conditions, do not use the system and contact your dealer for service or repairs; failure to do so may
result in serious injury.
Always exercise caution when handling, installing, and or using the system.
For additional care, usage, or general safety information, please call 1-800-451-1903.
Aluminum conducts electricity. Do not use or handle the system around live wiring or during electrical
storms.
TABLE OF CONTENTS
SECTION 1: CONFIGURATIONS ..................................................................................................................................5
SECTION 2: BASIC SYSTEM COMPONENTS............................................................................................................ 6-9
SECTION 3: PLATFORMS
INSTALL PLATFORMS.........................................................................................................................................10
INSTALL SUPPORT TUBES AND FEET, THEN ADJUST PLATFORM HEIGHT ................................................... 11-12
CONNECT TWO PLATFORMS TOGETHER .................................................................................................... 12-14
INSTALL UNIVERSAL ANGLE BRACE –PLATFORMS ...........................................................................................14
SECTION 4: RAMPS
CONNECT RAMP SECTIONS ...............................................................................................................................15
INSTALL RAMPS ON PLATFORMS ......................................................................................................................16
ATTACH SUPPORT LEG BRACKETS AND LEGS TO RAMPS............................................................................ 17-18
INSTALL UNIVERSAL ANGLE BRACE –RAMPS ...................................................................................................19
INSTALL RAMP GROUND TRANSITION ..............................................................................................................20
INSTALL A SINGLE RAMP RUN TO AN EXISTING STRUCTURE............................................................................21
ANCHOR RAMP UPPER TRANSITION.................................................................................................................22
ANGLE RAMPS WITH RESPECT TO PLATFORMS, PORCHES, OR DECKS....................................................... 22-23
BRIDGE PLATE ...................................................................................................................................................23
SECTION 5: HANDRAILS
RAMP HANDRAILS.............................................................................................................................................24
ASSEMBLE PLATFORM HANDRAILS...................................................................................................................25
INSTALL PLATFORM HANDRAILS.......................................................................................................................26
SECTION 6: CLOSURES
CLOSURE UPPER RAIL AND CURB................................................................................................................ 27-30
CLOSURE LOWER RAIL.......................................................................................................................................31
CLOSURE U-SHAPED..........................................................................................................................................32
SECTION 7: FINAL PLATFORM/RAMP STEPS AND CHECKS
SECURE RAMP TO PLATFORM...........................................................................................................................33
INSTALL RAMP HANDRAIL END LOOPS .............................................................................................................34
INSTALL RAMP CORNER PROTECTORS..............................................................................................................35
TOUCH-UP ARCHITECTURALLY FINISHED HANDRAILS ......................................................................................35
FINAL CHECKS....................................................................................................................................................35
SECTION 8: OPTIONAL EQUIPMENT
LANDING PAD....................................................................................................................................................36
RAMP LOWER TRANSITION...............................................................................................................................37
SECTION 9: MAINTENANCE & SAFETY
PERIODIC MAINTENANCE & SAFETY .................................................................................................................38
SECTION 10: DEICING...............................................................................................................................................38

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 5 of 39
1
1. CONFIGURATIONS
PATHWAY Aluminum Wheelchair Ramp Kits are available in three basic configurations: straight, L-shaped,
and U-shaped, with two platform sizes available, 4’ x 4’ and 5’ x 5’. All systems feature solid surface tread and
two-line handrails.
CONFIGURATION #
STYLE
AVAILABLE SIZES
CONFIGURATION 1
STRAIGHT
2’ INCREMENTS RANGING FROM 10’-30’ IN LENGTH
CONFIGURATION 2
STRAIGHT W/ 4’ X 4’ TOP PLATFORM
2’ INCREMENTS RANGING FROM 10’-30’ IN LENGTH
CONFIGURATION 3
STRAIGHT W/ 5’ X 5’ TOP PLATFORM
2’ INCREMENTS RANGING FROM 10’-30’ IN LENGTH
CONFIGURATION 4
L-SHAPED W/ 4’ X 4’ TURN PLATFORM
2’ INCREMENTS RANGING FROM 10’-30’ IN LENGTH
CONFIGURATION 5
L-SHAPED W/ 5’ X 5’ TURN PLATFORM
2’ INCREMENTS RANGING FROM 10’-30’ IN LENGTH
CONFIGURATION 6
L-SHAPED W/ 4’ X 4’ TURN AND TOP PLATFORM
2’ INCREMENTS RANGING FROM 10’-30’ IN LENGTH
CONFIGURATION 7
L-SHAPED W/ 5’ X 5’ TURN AND TOP PLATFORM
2’ INCREMENTS RANGING FROM 10’-30’ IN LENGTH
CONFIGURATION 8
U-SHAPED W/ 4’ X 4’ PLATFORMS
2’ INCREMENTS RANGING FROM 20’-30’ IN LENGTH
CONFIGURATION 9
U-SHAPED W/ 5’ X 5’ PLATFORMS
2’ INCREMENTS RANGING FROM 20’-30’ IN LENGTH

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 6 of 39
1
2. BASIC SYSTEM COMPONENTS
Because of varying lengths/configurations, your system may not contain all of these basic system components.
Identify your system components before you begin installation.
SURFACE OPTION
RAMP AND RAMP HANDRAIL OPTION
SOLID SURFACE
RAMP W/ TWO-LINE HANDRAIL
KEY RAMP COMPONENTS
PSLxxPR –SUPPORT LEG PAIRS
(xx DENOTES USABLE LENGTH)
PRGT –RAMP GROUND TRANSITION 18” X 36”
PRHBPR –RAMP HANDRAIL END BRACKET (PAIR)
PRRUC –UNIVERSAL CONNECTOR –RAMP TO RAMP
INCLUDES BASE FEET
INCLUDES
COMPONENTS TO
CONNECT RAMPS
AND RAMP
HANDRAILS
SHOWN ASSEMBLED

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 7 of 39
1
KEY RAMP COMPONENTS, CONT’D.
RAMP HANGER PAIR
PRUT –RAMP UPPER TRANSITION
PRHRLU –UPPER HANDRAIL END LOOP
PRHRLL –LOWER HANDRAIL END LOOP
PUAB –ANGLE BRACE
INCLUDES RAMP CORNER
PROTECTORS

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 8 of 39
1
PLATFORMS AND PLATFORM HANDRAILS
PLATFORM (STRAIGHT CONFIGURATION)
W/TWO-LINE HANDRAILS
PLATFORM (L-SHAPED CONFIGURATION)
W/TWO-LINE HANDRAILS
KEY PLATFORM COMPONENTS
PPPC –CONNECTOR –PLATFORM TO PLATFORM
PBP36 –BRIDGE PLATE
CLOSURE OPTION
PPCTL –TWO-LINE HANDRAIL CLOSURE
PTBCTL –TWO-LINE HANDRAIL CLOSURE U-SHAPED

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 9 of 39
1
ADDITIONAL OPTIONS
PLP –LANDING PAD
PRLT –RAMP LOWER TRANSITION

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 10 of 39
1
3. PLATFORMS
3.1. INSTALL PLATFORMS
If your configuration does not include a platform, skip to ‘CONNECT RAMP SECTIONS’.
Platform handrails are shown for clarity of how to orient platforms in various configurations. It is
strongly suggested that all platforms and ramps be installed before installing handrails (see
‘HANDRAILS’).
3.1.1. There are three basic platform arrangements (one or more of these arrangements may
be used in an installation). All require the same procedure for assembly except for FIG.2.3
which requires an additional PPPC (PLATFORM TO PLATFORM CONNECTOR).
FIG. 3.1 Straight
FIG. 3.2 L-shaped
FIG. 3.3 U-shaped
Two 5' x 5' platforms shown combined to make a 5' x 10’ U-shaped.
FIG. 3.1
FIG. 3.2
FIG. 3.3

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 11 of 39
1
3.2. INSTALL SUPPORT TUBES AND FEET, THEN ADJUST PLATFORM HEIGHT
3.2.1. Support tubes, plugs, and feet come in pairs. Support tubes will come in lengths sufficient
to accommodate a range of slope options.
ADA guidelines call for a maximum slope of 1:12 (approximately 5-degrees) and this is
the ideal slope for the system. However, the ramps can be installed from 1:14 to 1:8
(approximately 4- to 7-degrees). Do not attempt to install the ramps outside this range.
3.2.2. Loosen all set screws in the platform corner pockets.
3.2.2.1 The set screws on the outside of the platform are for the platform support tubes.
3.2.2.2 The set screws on the inside of the platform (one above the deck and one below
the deck) are for the handrail posts.
3.2.3. Tip the platform on its side, then slide the support tubes into the four platform corner
pockets (FIG.3.4). Adjust the support tubes to the approximate platform height needed.
3.2.4. Use a 3/16″ Allen wrench to tighten the upper of the two set screws in the corner pocket,
just enough to hold the support tube in place but do not over tighten (the second set
screw will be tightened after final height adjustments are complete).
Platforms configured in a U-shape (FIG. 3.3) will have six tubes to adjust.
Do not attempt to walk on the platform until all support tube set screws have been
tightened securely.
3.2.5. Place the platform (with support tubes attached) into the upright position.
Do not let the weight of the platform bear on the support tubes while tipping the
platform upright.
FIG. 3.4

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 12 of 39
1
3.2.6. Lift each corner of the platform and install a Base Foot (foot) on each support tube
oriented so that the foot extends under the platform (FIG. 3.4).
The feet can be oriented in other directions if necessary due to site conditions but
may present a tripping hazard if not oriented under the platform.
It is the installer’s responsibility to install the system in a manner which is safe for the
persons on and around the system and clearly mark any hazards created by the
installation.
3.2.7. Make sure each foot is fully engaged on the tube and tighten the thumb screw securely.
If installing on soft soil it may be necessary to set the foot on a concrete pad.
3.2.8. Adjust the final height of the platform by adjusting legs, one at a time, by loosening the
outer set screws in the platform corner pockets. Using a level, adjust the platform height
and re-tighten.
3.2.9. Once the final height has been adjusted, tighten the second, lower set screw in each
platform corner pocket.
3.2.10. To allow access to the lowermost hole in the platform post, the support tubes must not
extend more than 1/2” above the platform corner pockets. Trim the support tubes as
needed before installing plugs.
3.2.11. Insert a plug into the top of each support tube. Use a rubber mallet or similar tool as
needed (FIG. 3.4).
3.2.12. Ensure all set screws are tightened securely.
3.3. CONNECT TWO PLATFORMS TOGETHER (U-SHAPED CONFIGURATIONS ONLY)
If your system does not include a U-shaped configuration but does include a platform, skip to
‘INSTALL UNIVERSAL ANGLE BRACE –PLATFORMS’.
3.3.1. Assemble the first platform as described in the previous steps except on the side where
the second platform will connect, install two PPPC (CONNECTOR –PLATFORM TO
PLATFORM) before installing feet onto the support tubes.
3.3.2. Make sure the platform connector set screws are oriented outward so they will be
accessible.
Any two platforms of the same width can be connected.
3.3.3. Slide the platform connectors up until they contact the bottom of the platform and
tighten the set screws securely (FIG. 3.5).
3.3.4. Install a support tube stub into the open pocket in each connector until the bottom of
the stub is flush with the bottom of the connector and tighten the set screws securely.
3.3.5. Install a plug in the top of each support tube stub (FIG. 3.5).
3.3.6. Assemble the second platform as described in the previous section except only install
support tubes, plugs, and feet on the opposite side of where the platforms will connect
(FIG. 3.6).
3.3.7. Lift the second platform and slide the open corner pockets over the support tube stubs
extending up from the platform connectors. Tighten the set screws in the platform
corner pockets securely.
3.3.8. Adjust the platform heights and level as needed.
Make sure all the set screws in both the platform corner pockets and the platform
connectors are tightened securely before proceeding with the installation.

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 13 of 39
1
FIG. 3.5
FIG. 3.6

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 14 of 39
1
3.4. INSTALL UNIVERSAL ANGLE BRACE –PLATFORMS
For added stability, any platform with a walking surface over 36″ high requires bracing. The PUAB
(PATHWAY ANGLE BRACE) is used for all surfaces 36″ elevation and over.
3.4.1. Angle braces come in pairs. Use four pairs per platform (one pair per support tube,
or side) or six pairs when two platforms are connected.
3.4.2. Use two brace bands to secure the ends of the two angle braces nearest the twist to
the support tube using a 5/16" bolt, flat washer, and nut (FIG. 3.7).
3.4.3. Opposite ends of the braces are attached to the bottom of the platform side rail at
90-degrees to each other using a 1/4″x 1” long self-drilling screw (FIG. 3.7).
Ensure that all angle braces are secured before using platform.
FIG. 3.7

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 15 of 39
1
4. RAMPS
4.1. CONNECT RAMP SECTIONS
If your configuration does not contain two or more consecutive ramps, skip to 'INSTALL A SINGLE
RAMP RUN TO AN EXISTING STRUCTURE’.
4.1.1. Place the walking surface side of the ramp sections face down, onto cardboard or lawn so
that the ramp is not damaged (scratched or dented).
4.1.2. Butt the sections together end-to-end and ensure there is no gap, then position the two
center saddle brackets, included in the PRRC (CONNECTOR –RAMP TO RAMP), over the
threaded inserts at the end of each ramp section (FIG. 4.1).
4.1.3. One edge of the center saddle bracket will slide into the groove of the ramp sections.
To create a run, ramp sections are connected using two interchangeable center
saddle brackets per joint. The center saddle brackets are also where the handrails
and ramp legs are attached.
4.1.4. Attach the center saddle brackets using four each 5/16″-18 x 1-1/2″ bolts and 5/16″
washers per bracket. Tighten all eight bolts (four each per center saddle bracket).
Although a system can have multiple ramps per run, it is recommended that a
maximum of three ramp sections at a time be joined in this manner.
4.1.5. Install four end brackets, PRHBPR (RAMP HANDRAIL END BRACKET PAIR). These will be
used to attach handrails in a later step. Use one end bracket at each outside corner of the
ramp or ramp run using one 5/16″ x 1-1/2″ bolt and washer into the threaded insert
closest to the end of the ramp (FIG. 4.2).
4.1.6. Turn the joined ramps to their upright position, being careful not to damage the
threaded studs.
FIG. 4.1
(BOTTOM VIEW)
FIG. 4.2
(BOTTOM VIEW)

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 16 of 39
1
4.2. INSTALL RAMPS ON PLATFORMS
If your configuration does not include a platform, skip to ‘ATTACH SUPPORT LEG BRACKETS AND
LEGS TO RAMPS’.
This section addresses the attachment of a ramp or ramp run to a platform. If the ramp needs to
be angled with respect to the platform or is going to be attached to an existing porch, skip to
‘ANGLE RAMPS WITH RESPECT TO PLATFORMS, PORCHES, OR DECKS’.
4.2.1. Ramps must be placed on either the left or right side of the platform (cannot be centered).
4.2.1.1. Place the ramp in a location that ensures the ramp handrail post is positioned
1-1/2” (minimum) to 2” from the inside of the platform post.
4.2.2. Locate the PRHP (RAMP HANGER PAIR) and install the two hangers in the platform side rail
where the ramp will be attached.
4.2.3. Hold the hanger perpendicular (approximately) to the platform side rail then bring the
hanger upward until it is against the side rail lip. Rotate the hanger and continue pushing
upward in such a manner that the “hook″ at the top of the hanger goes behind and catches
on the lip in the top of the platform side rail and the hanger sits on the ledge at the bottom
(FIG. 4.3).
4.2.4. Set the ramp on the hangers. The hangers should be positioned as close as possible to the
ramp side rails. The procedure is the same at both the top and bottom of ramp runs which
end at a platform unless a transition plate is used (FIG. 4.4).
Do not attempt to walk on the system until installation is complete.
FIG. 4.3
(TOP VIEW)
FIG. 4.4
(TOP VIEW)

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 17 of 39
1
4.3. ATTACH SUPPORT LEG BRACKETS AND LEGS TO RAMPS
4.3.1. Install the Support Leg Bracket (bracket), included with PRRUC, onto the center studs of
the Center Saddle Bracket (ramp connector included with PRRUC) with the round hole on
the upper stud and the curved slot over the lower stud (FIG. 4.5).
4.3.2. Attach the bracket using the provided 5/16” flat washers and 5/16”-18 nylon insert
locknuts onto the studs but do not tighten fully until the bracket has been leveled.
FIG. 4.5
FIG. 4.6

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 18 of 39
1
4.3.3. Level the bracket using a bubble level or similar tool, then torque the 5/16”-18 nylon insert
locknuts to 20 ft.-lbs.
4.3.4. Locate the appropriate PRLxxPR (SUPPORT LEG PAIR where “xx” denotes the leg length)
for the location. Place a foot under the bracket with the foot extending under the ramp,
then insert a 1-1/2” square Support Leg (leg) through the bracket into the foot. Loosen
the 3/8”-16 headless socket set screws and the foot thumb screw if needed to fully
engage the leg in the foot (FIG. 4.6).
If installing on soft soil it may be necessary to set the foot on a concrete pad.
4.3.5. After the leg is fully engaged in the foot, tighten the 3/8”-16 headless socket set screws
to 15 ft.-lbs. (FIG 4.6).
Do not attempt to walk on the ramps until all leg set screws have been tightened as
specified.
4.3.6. Tighten the foot thumb screw and insert 1-1/2” square plug into the top of the leg (FIG. 4.6).
4.3.7. Repeat the above procedure at all locations where ramps connect.
4.3.8. Adjust the legs one at a time.
4.3.9. Raise the ramp sections (at the center saddle bracket) to take any sag out of the ramp
run, then tighten the two locknuts in each leg.
ADA guidelines call for a maximum slope of 1:12 (approximately 5-degrees) and this is
the ideal slope for the system. However, the ramps can be installed from 1:14 to 1:8
(approximately 4- to 7-degrees). Do not attempt to install the ramps outside this range.
Adjusting sections can be accomplished by having someone sight down the ramp
while another person adjusts the ramp height.
Ensure that the ramp sections are parallel to each other. If they are not, it may be
difficult to install the handrails (FIG. 4.7).
4.3.10. Insert a plug into the top of each leg (FIG. 4.6).
4.3.11. Ensure that all bolts are tight and that the ramp sections are aligned parallel to one another.
FIG. 4.7

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 19 of 39
1
4.4. INSTALL UNIVERSAL ANGLE BRACE –RAMPS
If the walking surface is over 36″ high, a PUAB (UNIVERSAL ANGLE BRACE) must be installed
under the ramp (FIG. 4.8).
4.4.1. Angle Braces (braces) come in pairs; use one pair per ramp connection.
4.4.2. The brace bands are installed on ramp legs in the same manner as platform legs (refer to
‘INSTALL UNIVERSAL ANGLE BRACE – PLATFORMS’).
4.4.3. The opposite end of the brace is attached to the bottom of the ramp (near the center of
the tread at the end of the ramp) using a 1/4″ x 1” long self-drilling screw.
Ensure that all braces are secured before using the ramp.
FIG. 4.8

PATHWAY®Aluminum Wheelchair Ramp Kit
Page 20 of 39
1
4.5. INSTALL RAMP GROUND TRANSITION
4.5.1. The PRGT (RAMP GROUND TRANSITION) consists of two sections that need to be
installed into the ramp and connected together.
The Ramp Ground Transition is only designed to transition from the lowest ramp in
the run to the ground; do NOT USE in any other location.
4.5.2. Lift the lowest end of the ramp/ramp run and bring the upper section of the Ramp
Ground Transition into the ramp end tread until the “hook” is engaged (FIG. 4.9).
4.5.3. Rotate into place (FIG. 4.10) and set back on the ground.
4.5.4. Slide the lower section into upper section (FIG. 4.11).
4.5.5. Install #8-32 x 1/2” hex washer head thread cutting screws into the screw slots on both
sides where the sections connect (FIG. 4.12).
The hex washer head screws will keep the sections from sliding with respect to each
other, but the sections can still be separated until they are installed in the ramp and
resting on the ground.
4.5.6. Holes and fasteners are included for anchoring into wood or concrete. Other methods
may be used when anchoring into other surfaces.
4.5.7. If connecting the lowest end of the ramp to a PLP (LANDING PAD), use a PRLT (RAMP
LOWER TRANSITION), which is included with the landing pad, instead of a PRGT (RAMP
GROUND TRANSITION). Please see ‘OPTIONAL EQUIPMENT’ for instructions.
FIG. 4.9
FIG. 4.10
FIG. 4.11
FIG. 4.12