Fab Fours D4351 User manual

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 1 of 9
SAFETY
Your safety and the safety of others is very important.
In order to help you make informed decisions about safety, we have provided
installation instructions and other information.
These instructions alert you to potential hazards that could hurt you or others.
Please do a job safety analysis before each task to identify potential hazards for your
situation and remove/protect against them.
You must use your own good judgment, and take your time.
Read and understand all safety precautions and instructions before installing this product.
THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR
INSTALLATION AND USE RESTS WITH THE OWNER.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY
OR EQUIPMENT DAMAGE.
Injury hazard
Failure to observe these instructions could lead to severe injury or death.


Always remove jewelry and wear eye protection.


Always use extreme caution when jacking up a vehicle for work. Set
emergency brake and use tire blocks. Locate and use the vehicle
manufacturers designated lifting points. Use jack stands.


Always use appropriate and adequate care in lifting components into place.


Always insure components will remain secure during installation and
operation.


Always wear safety glasses when installing this kit. A drilling operation will
cause flying metal chips. Flying chips can cause serious eye injury.


Always use extreme caution when drilling on a vehicle. Thoroughly inspect
the area to be drilled (on both sides of material) prior to drilling, and
relocate any objects that may be damaged.


Always use extreme caution when cutting and trimming during fitting.


Always tighten all nuts and bolts securely per installation instructions.


Always route electrical cables carefully. Avoid moving parts, components
that become hot and rough or sharp edges.


Always insulate and protect all exposed wiring and electrical terminals.


Always perform regular inspections and maintenance on mounts and
related hardware.

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 2 of 9
I. Overview
Congratulations on your new purchase of the industries’ best and most stylish
front bumper available for the 2017 Ford Raptor. This bumper has been
designed to be lightweight and easily customized with the industry’s highest
quality accessories.
Your front bumper designed in 3-D from digitized data, CNC laser cut,
fabricated, and powder coated… all in the U.S.A.
Enjoy the fit and finish of a quality Vengeance Ford Raptor Front Bumper from
Fab Fours Inc.

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 3 of 9
Parts List
D435X replacement bumper
50013-HW fastener kit
Instruction manual
Tools Required
Socket wrench with extension (ratcheting wrenches may also be
convenient)
8mm, 11mm, 13mm, 15mm, 21mm, 9/16 and 5/8”sockets and box end
wrenches
E6 External torx socket
Flat head screw drivers
Floor jack and wood block.
II. Removal of OEM Bumper
Note: Save all OEM parts until installation is complete!
A. From underneath the front of the truck remove the six (6) fasteners attaching
the OEM skid plate to the truck with a 13mm and 15mm socket. And set
aside along with metal spacer at back of skid plate; see below:

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 4 of 9
B. Using a flathead screwdriver, carefully remove center plastic piece, indicated
by oval in the center of the OE bumper.
Figure 1a
Figure 1b
C. Using 21 mm socket, remove the three nuts per side, two are located under
the plastic center piece (ref. fig. 2a-b) and the third accessible from the back
of the frame (ref. fig. 2c). If front OEM bumper contains sonar (ref. fig. 2b),
remove three nuts with 11 mm. If your bumper includes a radar device,
remove it now using an E6 external torx socket. Unplug the device.

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 5 of 9
Figure 2a Figure 2b
Figure 2c
D. Remove two 8mm bolts one per side that hold on the bumper side support
bars from the truck side leaving the support bars attached to the bumper.
E. At this time, carefully pull away bumper and remove the rubber shroud
connectors along the top.
F. Pull rubber covers off the tow hooks.

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 6 of 9
G. If your vehicle model includes a louver system for the intercooler located
between the frame mounts, the shroud must be removed. Special care must
be taken not to damage louvers when cutting around the base of the
rectangular shroud, a cut off wheel is recommended.
Figure 4 (Louver w/ shroud cut away at base)

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 7 of 9
III. Pre-Installation
NOTE: The following installation steps apply to the installation of the front bumper.
PLEASE READ THE ENTIRE MANUAL BEFORE ATEMPTING
INSTALLATION. Ignoring these steps will increase your probability of scratching
the vehicle during product installation.
A. Remove the bumper from the shipping carton. Lay all items out on a
blanket to prevent damage to the powder coating.
B. If you are installing aftermarket lights, do the wiring for those now
and install them into the bumper. (But don’t plug them in until after
bumper install)

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 8 of 9
IV. Front Bumper Installation
A. Use painter’s tape to tape off the valence of your truck to help prevent
scratching the paint.
B. Using the supplied hardware and a 5/8 socket, mount the bumper to
your truck but do not fully tighten. There will be 6 bolts.
C. Adjust the height of the bumper to the truck and tighten the bolts.
(Fab Fours recommends 1/4 profile gap as a standard.)
D. Re-install factory skid plate using OEM hardware, and supplied
spacers if necessary to ensure the skid plate is not rubbing the
bumper.
E. Enjoy your new Vengeance Front Bumper from Fab Fours!

Installation Instructions
Ford Raptor Vengeance Front
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Page 9 of 9
Maintenance/Care


Periodically check and tighten all fasteners.


Stripped, fractured, or bent bolts or nuts need to be replaced.


After washing of the vehicle make sure to fully dry all surfaces
More than expected… Better than expected