Fab Fours JL3021-22 User manual

Installation Instructions
Vi-Cowl Light Insert
Product Number: JL3021-22
2018 Jeep JL 4 Door
Copyright 2009 Fab Fours, Inc. Page 1 of 5 Jl3021-22_Installation_Manual_REV_A
! IMPORTANT SAFETY GUIDE
Your safety and the safety of others is very important.
In order to help you make informed decisions about safety, we have provided the
following warnings, safety precautions, installation instructions, and other important
information to alert you to potential hazards that could hurt you or others.
Please do a job safety analysis before each task to identify potential hazards for your
situation and remove/protect against them.
Use own good judgment and take your time.
Check packaged materials immediately upon arrival to ensure that all listed parts are
included and undamaged.
Read and understand all warnings, safety precautions, and instructions before installing
this product.
SENSORS’FIELD OF VIEW WILL BE ALTERED WITH USE OF THE
REPLACEMENT BUMPER.
WARNINGS
FAILURE TO OBSERVE THE FOLLOWING WARNINGS AND
INSTRUCTIONS PROVIDED IN THIS MANUAL COULD LEAD TO
SEVERE INJURY AND/OR DEATH.
FOR PROFFESIONAL INSTALLATION ONLY. CARELESS
INSTALLATION AND/OR OPERATION CAN RESULT IN SERIOUS
INJURY, DEATH, AND/OR EQUIPMENT DAMAGE. ALL LIABILITY FOR
INSTALLATION AND USE RESTS WITH THE USER OR CONSUMER.
FAB FOURS, INC. ONLY APPROVES INSTALLING THIS PRODUCT
ACCORDING TO THESE WRITTEN INSTRUCTIONS WITH THE
HARDWARE PROVIDED. FAILURE TO INSTALL ACCORDING TO
THESE INSTRUCTIONS WILL INVALIDATE THE WARRANTY. THIS
INCLUDES, BUT IS NOT LIMITED TO, USING ALTERNATIVE
INSTALLATION METHODS, HARDWARE, OR MATERIALS.
THIS PRODUCT IS FOR OFFROAD USE ONLY.

Installation Instructions
Vi-Cowl Light Insert
Product Number: JL3021-22
2018 Jeep JL 4 Door
Copyright 2009 Fab Fours, Inc. Page 2 of 5 Jl3021-22_Installation_Manual_REV_A
SAFETY PRECAUTIONS
oAlways remove jewelry and wear eye protection.
oAlways use extreme caution when jacking up a vehicle for work. Set
emergency brake and use tire blocks. Locate and use the vehicle
manufacturers designated lifting points. Use jack stands.
oAlways use appropriate and adequate care in lifting components into place.
oAlways ensure components will remain secure during installation and
operation.
oAlways wear safety glasses when installing this kit. A drilling operation will
cause flying metal chips. Flying chips can cause serious eye injury.
oAlways use extreme caution when drilling a vehicle. Always disconnect
power before welding. Thoroughly inspect the area to be drilled (on both
sides of material when possible) prior to drilling, and relocate any objects that
may be damaged.
oAlways use extreme caution when welding a vehicle. Thoroughly inspect the
area to be welded (on both sides of material when possible) prior to welding,
and relocate any objects that may be a fire hazard. When welding in a cab,
make sure the interior surfaces are covered (e.g., welding blanket) and a fire
extinguisher is at hand.
oAlways use extreme caution when cutting and trimming during fitting.
oAlways tighten all nuts and bolts securely per installation instructions.
oAlways route electrical cables carefully. Avoid moving parts, components
that become hot, and rough or sharp edges.
oAlways insulate and protect all exposed wiring and electrical terminals.
oPerform regular inspections and maintenance on mounts and hardware.
oTire may rub at max turn or articulation.

Installation Instructions
Vi-Cowl Light Insert
Product Number: JL3021-22
2018 Jeep JL 4 Door
Copyright 2009 Fab Fours, Inc. Page 3 of 5 Jl3021-22_Installation_Manual_REV_A
Overview
Congratulations on your new purchase of the Fab Fours Vi-Cowl Accessory.
Your Vi-Cowl light insert was designed in 3-D from digitized data, CNC laser cut,
fabricated, and powder coated… all in the U.S.A. Enjoy the fit and finish of a Vi-
Cowl from Fab Fours, Inc.
WARNING: This product was designed to be used with the 2018 Jeep Wrangler JL
ONLY.

Installation Instructions
Vi-Cowl Light Insert
Product Number: JL3021-22
2018 Jeep JL 4 Door
Copyright 2009 Fab Fours, Inc. Page 4 of 5 Jl3021-22_Installation_Manual_REV_A
I. Tools Required
3/16” Allen Wrench
Socket Set and Ratchets
II. Installation of Vi-Cowl Light Insert
1. The vi-cowl must be removed from the vehicle prior to
installation of the light insert. Please refer to the Vi-Cowl
installation manual for removal instruction.
2. Remove the standard visor trim panel and save the
hardware as it will be used to install the light insert
3. Install any lights into the light insert and perform the
necessary wire splicing and wire routing.
4. Install the light insert into the vi-cowl using the existing
stainless steel hardware.
5. Install the Vi-Cowl. Please refer to the Vi-Cowl Installation
manual for instruction.

Installation Instructions
Vi-Cowl Light Insert
Product Number: JL3021-22
2018 Jeep JL 4 Door
Copyright 2009 Fab Fours, Inc. Page 5 of 5 Jl3021-22_Installation_Manual_REV_A
III. Maintenance/Care
Periodically check and tighten all nuts.
Stripped, fractured, or bent bolts or nuts need to be replaced.
IV. Contact Information
Fab Fours Inc. Phone [phone]
2213 Industrial Park Road Fax [phone]
Lancaster, SC 29720 Email [email protected]
More than expected… Better than expected.