Fab Fours Vengeance Light Mesh User manual

Installation Instructions
Vengeance Light Mesh
For the Vengeance Front Bumper Line
SAFETY
Your safety and the safety of others is very important.
▪In order to help you make informed decisions about safety, we have provided installation
instructions and other information.
▪These instructions alert you to potential hazards that could hurt you or others.
▪Please do a job safety analysis (JSA) before each task to identify potential hazards for
your situation and remove/protect against them.
▪You must use your own good judgment, and take your time.
Read and understand all safety precautions and instructions before installing this product.
THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION
AND USE RESTS WITH THE OWNER.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY
OR EQUIPMENT DAMAGE.
Injury hazard
Failure to observe these instructions could lead to severe injury or death.
❑Always remove jewelry and wear eye protection.
❑Always use extreme caution when jacking up a vehicle for work. Set emergency
brake and use tire blocks. Locate and use the vehicle manufacturers designated
lifting points. Use jack stands.
❑Always use appropriate and adequate care in lifting components into place.
❑Always insure components will remain secure during installation and operation.
❑Always wear safety glasses when installing this kit. A drilling operation will
cause flying metal chips. Flying chips can cause serious eye injury.
❑Always use extreme caution when drilling on a vehicle. Thoroughly inspect the
area to be drilled (on both sides of material) prior to drilling, and relocate any
objects that may be damaged.
❑Always use extreme caution when cutting and trimming during fitting.
❑Always tighten all nuts and bolts securely per installation instructions.
❑Always route electrical cables carefully. Avoid moving parts, components that
become hot and rough or sharp edges.
❑Always insulate and protect all exposed wiring and electrical terminals.
❑Always perform regular inspections and maintenance on mounts and
related hardware.

Installation Instructions
Vengeance Light Mesh
For the Vengeance Front Bumper Line
Overview
Congratulations on your new purchase of the Vengeance Mesh Cover Accessory.
Your license plate bracket was designed in 3-D from digitized data, CNC laser cut,
fabricated, and powder coated… all in the U.S.A. Enjoy the fit and finish of a quality
Vengeance front bumper and Mesh Cover from Fab Fours, Inc.
WARNING: This product was designed to be used with Fab Fours Vengeance front
bumpers ONLY.
I. Tools Required
•½” Wrench or socket
•Socket wrench
•3/16” Allen Wrench
II. Mesh Cover Installation
Note: There are two different types of mounting methods used for Vengeance grill
mesh. One method uses the lighting mounting slots on the top of the light box. The
other method uses to same mounting points as what the light box uses to tighten to
the shell of the bumper. Both methods are detailed below, and example images
shown on the next page.
Note: the images below may not look exactly like your product as this manual is a
general grill mesh manual
1. Using the provided 5/16” hardware, attach the Mesh Cover using the
provided holes in the light cutouts of the bumper. Adjust so that the
mesh is aligned with the cutout
2. Remove the two bolts from the light box that are used to secure the
grill mesh to the back of the light box. Layer the mesh to the back of the
box and reinstall the appropriate hardware previously removed.

Installation Instructions
Vengeance Light Mesh
For the Vengeance Front Bumper Line
Fig 1. (Method 1)
Fig 2. (Method 2)

Installation Instructions
Vengeance Light Mesh
For the Vengeance Front Bumper Line
III.Maintenance/Care
❑Periodically check and tighten all nuts.
❑Stripped, fractured, or bent bolts or nuts need to be replaced.
❑Periodically grease the tire carrier pivot.
❑Periodically check the tension of the latch hook..
Check out the collection of off-road bumpers we offer.