Faber SILENCE Assembly instructions

installation guide and user manual
room-sealed built-in gas-fireplace
40 010 527
02 37
SILENCE
FEELING
WHISPER
SPECTRA NOVA
CADRA NOVA
MISTY
Saturnus 8 NL-8448 CC Heerenveen
Postbus 219 NL-8440 AE Heerenveen
T. [phone]
F. [phone]
“Log Burner Technology”

1
CONTENTS
1. INTRODUCTION 2
2. SAFETY INSTRUCTIONS 3
3. INSTALLATION REQUIREMENTS 5
3.1 Builders opening and surround 5
3.2 Requirements outlet and exhaust 8
4. INSTALLATION-INSTRUCTIONS 17
4.1 Gas connection 17
4.2 Preparation of the appliance 17
4.3 Fitting the firebox 24
4.4 Placing of the wood set 26
5. INSTALLATION OF THE FLUE 27
5.1 Connection of the flue 27
5.2 Placing through existing chimney 28
5.3 Remote control 30
6. COMMISIONING 32
6.1 Check pilot ignition 32
6.2 Functional burner check 32
6.3 Functional balanced flue check 33
6.2 Check reference pressure 33
7. HANDING OVER 34
8. SERVICING 35
8.1 Routine annual servicing 35
USER GUIDE 45
9. SAFETY INSTRUCTIONS FOR THE USER 46
10. CONTROLING THE APPLIANCE 48
11. CLEANING AND SERVICE INSTRUCTIONS 54
12. DISPOSAL OF THE PACKAGING AND THE APPLIANCE 55
INDEX 1 LIST OF SPARE PARTS 40
INDEX 2 TECHNICAL DATA 41
UK/IRL

UK/IRL
2
UK/IRL
3
1. INTRODUCTION
Note: these instructions should be read carefully and retained for
future reference.
lease leave these instructions with the user.
This guide is concerning the following types of appliances:
Widescreen interior: Types Silence and Feeling
Roundscreen interior: Type Misty
MV100 interior: Type Whisper
MV110 interior: Types Spectra Nova and Cadra Nova
Special features:
- Realistic flame and glow effect because of the "Log burner"
technology.
- Room sealed appliance, inlet and outlet are led to the outside
using a natural draught concentric pipe system (100 mm/150 mm
(no power fan required . No additional ventilation required.
- Air supply and flue-gases go to outside atmosphere through wall or
roof. A maximum horizontal extension of 6 meters is possible.
- Remote Control option on all appliances.
- Meets the essential requirements of the European Gas Appliance
Directive (GAD and carries the CE mark.
2. SAFETY AND GENERAL
INFORMATION
Before installation, ensure that the local distribution conditions
(identification of the type of gas and pressure and the adjustment of
the appliance are compatible.
This gas appliance is factory set and shall not be adjusted by the
installer.
This appliance does not contain any component manufactured from
asbestos or any asbestos related products.
The pilot and flame sensing device fitted to this fire is also a safety
device. If for any reason any part of the pilot assembly is to be
replaced the entire assembly including the pilot burner, thermocouple,
electrode and injector must be exchanged complete for a pilot assembly
from the original manufacturer only.
Ventilation
This appliance is room-sealed and doesn't require purpose provided
ventilation.
2.1 General safety
It is the law in the UK that all gas appliances, are installed by a
competent person in accordance with the Gas Safety (Installation and
Use Regulations (as amended , the relevant British Standards for
Installation work, Building Regulations, Codes of Practice and the
manufacturers instructions.
The installation should also be carried out in accordance with the
following where relevant:
BS5871 Part1 BS5440 Parts 1 & 2 BS1251.
Building Regulations Document J (as applicable .

UK/IRL
5
UK/IRL
4
Building Regulations and Standards issued as relevant by the
Department of the Environment or the Scottish Development
Department.
In the Republic of Ireland installation should be carried out in
accordance with IS813, ICP3, IS327, Building Regulations, Codes of
Practice, the manufacturers instructions and any other rules in force.
Failure to comply with the above could leave the installer liable to
prosecution and invalidate the appliance warranty.
Safety instructions for the user: see chapter 9.
3. INSTALLATION REQUIREMENTS
Note:
Since the appliance is a source of heat, circulation of air occurs.
Therefore it is of importance that you do not use the appliance
shortly after a renovation of the home. Because of the natural
circulation of air, moist and volatile components from paint, building
materials, carpet etc. will be attracted. These components can settle
themselves down onto cold surfaces in the form of soot.
As on all heat producing appliances, soft furnishings such as blown
vinyl wallpaper placed too near to the appliance may become
scorched or discoloured. This should be born in mind when installing
the appliance.
3.1 Builders opening and surround
The appliance can be installed in the following situations:
In a non-combustible fireplace or builders opening. This could be either
an existing builders opening or a new made prefab builders opening.
For the measurements, see figure 1 and index.
Although the appliance is tested for installation without a hearth, the
appliance must not stand on combustible materials or carpets. If the
appliance is placed on a combustible floor then a fibrelux or similar
heatproof board of 12 mm thickness should be placed under it. Any
under floor vents or openings within the builders opening should be
sealed off.
Do not place the lintel, surround or marble stone directly onto the
appliance. If possible, apply a lintel made of cement or something
similar.
Isolate the appliance with a ceramic blanket (25 mm . See also
chapter 4: Installation instructions.
Preferred choice for insulation is unbound insulation wool (at
1000 °C gives no smell .

LM
F
I
CB
A
J
E
D
G
K
H
Builders opening (mm) Feeling Silence Whisper Spectra Cadra Misty
Nova Nova
A Opening width* 960 960 780 780 680 710
B Opening height* 649 649 705 698 798 890
C Opening depth* 385 385 430 430 430 370
Shelf dimensions
(combustible)
D Min. height shelf from
top frame 350 350 350 350 350 350
E Depth shelf max. 150 150 150 150 150 150
Dimensions (mm)
F Box width 880 880 750 750 650 698
G Box depth 366 366 397 375 375 338
H Box height 636 636 714 715 815 879
I Frame width 1064 1064 815 794 694 740
J Frame height 678 678 720 703 803 905
K Frame thickness 47 20 16 30 30 144
L Position flue
(behind frame 255 255 257 235 235 196
M Position flue (from the
back side box 111 111 140 140 140 142
UK/IRL
7
UK/IRL
6
3.1 Builders opening and surround (continuing)
If the builders' opening is constructed out of non-combustible
composition board (Fibrelux and you install the appliance without a
mantel then:
- Ventilate the space above the appliance (min. 1000 mm2 .
- Always fit the DC convection set.
- The plaster of the outside has to be resistant to a high
temperature. Use therefore the plaster materials especially made for
this, to prevent discoloring (min. 100 °C temperature resistant .
If the appliance is to be fitted against a wall with combustible
cladding, the cladding must be removed from the area covered by the
surround.
The minimum height from the top surface of the fire to the underside
of any shelf made from wood or other combustible materials is as
follows:
- For a shelf up to 150 mm deep – Minimum height = 350 mm
(fig. 1 .
- If the shelf depth is greater than 150 mm add 50 mm to the upper-
clearance height for every 25 mm increase in shelf depth.
- Side clearance = Minimum distance from the side of the fire frame
to combustible material = 150 mm.
fig. 1
table 1
*the points A until C applies a tolerance from:
– 0 mm and + 5 mm.

UK/IRL
9
UK/IRL
8
3.2 Flue requirements
The appliance is of the type C11/C31. The appliance will need to be
supplied with the approved flue pipes and terminal, it is not possible to
supply your own.
The minimum effective height of the flue system must be 0.5 or 1 meter,
depending on the appliance.
Terminal locations, through the wall as well as through the roof. See
figure 3.
Flue routing;
- a horizontal extension with elbows is allowed for a maximum of
6 meters (depending on the type and situation .
- vertical max. 12 meters.
Determine on the base of the table 2 and 3, depending on the type
and terminal position, if the desired situation is possible.
To establish this you will need to calculate:
- The effective height (this is the real difference in height between the
upper side of the appliance and the terminal .
- The total horizontal extension. This is the total horizontal flue length
where:
• each elbow, which is in the horizontal area, counts for 2 meters.
• each 45-degree bend, which is in the horizontal area, counts for
1 meter.
• elbows and bends at the transition of horizontal to vertically are
not to be counted.
• the wall mounted terminal counts for 1 meter.
Flue restrictor
If applicable, in the table is also stated the size of a flue restrictor.
This restrictor needs to be fitted in the combustion chamber when
placing the appliance ( see chapter 4.2 . Normally the smallest flue
restrictor is fitted.

UK/IRL
0123456
0XXXXXXX
XXXXXX
XXXXX
XXXX
XXX
XX
X
1 30 0 0 0 0 0 0/X*
23030 0 0 0 0 0
3 454530 0 0 0 0
4 454530 0 0 0 0
5 5050454530 0 0
6 5050454530 0 0
7 606060505045
8 6060606050
9 65656060
10 65 65 65
11 65 65
12 65
Horizontal extension
Effective height
X combination
not allowed
0 remove flue restrictor
Number is size in mm
of the flue restrictor
Table Silence and Feeling with interior Widescreen
Determine according to the table 2 the right total horizontal- and vertical length.
When meeting an X, and when the values are outside the table, the combination is
not allowed. Normally the 30 mm flue restrictor is preinstalled.
Table Whisper and Spectra Nova with interior MV100
Determine according to the table 3 the right total horizontal- and vertical length.
When meeting an X, and when the values are outside the table, the combination is
not allowed. Normally the 30 mm flue restrictor is preinstalled.
0123456
0XXXXXXX
XXXXXX
XXXXX
XXXX
XXX
XX
X
XXXXX
XXX
1 0 0
1,5 0 0 0 0
2303000000
345453030000
4 4545303030 0 0
5 505045303030 0
6 505045303030 0
7 606050454530
8 6060605050
965
65 60 60
10 65 65 65
11 65 65
12 65
X combination
not allowed
0 remove flue restrictor
Horizontal extension
Effective height
Number is size in mm
of the flue restrictor
table 2
interior Widescreen
table 3
interior MV100
UK/IRL
10
fig. 2a
Hvert.
N
M
L
K
J
I
H
fig. 2b
Hvert.
A
F
G
E
D
C
B
Example calculation 1
Calculati0n horizontal extension fig. 2a:
Flue lenght C + E = 1m + 1m 2 m
Elbows D = 2m 2 m
Total horizontal extension 4 m
Measure or calculate effective height (Hvert)
Flue lenght A 1 m
Roof mounted terinal 1 m
Total effective height 2 m
When calculating on basis of the
Widescreen table nr. 2:
It is allowed.
Remove the flue restrictor!
When calculating on basis of the
MV100 table nr. 3:
Allowed but without flue restrictor.
Remove the flue restrictor!
When calculating on basis of the
MV150 table nr. 4:
Allowed but without flue restrictor.
Remove the flue restrictor!
When calculating on basis of the
Roundscreen table nr. 5:
Allowed but without flue restrictor.
Remove the flue restrictor!
11
* at propane not allowed
Example calculation 2
Calculati0n horizontal extension fig. 2b:
Flue lenght J + L = 0,5 + 0,5 1 m
Elbows K + M = 2m + 2m 4 m
Terminal 1 m
Total horizontal extension 6 m
Vertical
Flue lenght H1 m
When calculating on basis of the
Widescreen table nr. 2:
Combination not allowed.
When calculating on basis of the MV100
table nr. 3:
Allowed but without flue restrictor.
Remove the flue restrictor!
When calculating on basis of the MV150
table nr. 4:
Combination not allowed.
When calculating on basis of the
Roundscreen table nr. 5:
Combination not allowed.

UK/IRL
13
3.2 Flue requirements (continuing)
3.2.1 Terminal position
Verify if the required terminal position meets the local installation
regulations regarding disturbance, good functioning and ventilation.
(Also see: safety requirements .
Note:
The terminal must be located so that the outlet is not obstructed. If
the flue terminal is located within 2 meters of a footway, path or
where people could come into contact with it then a suitable
terminal guard must be fitted.
Terminals located close to shared walkways, footpaths etc. could be
subject to legal constraints and this should be pointed out to the
customer before installation. If in any doubt about flue location
advice should be sought from local building control, or if appliance-
related, from the manufacturer including wherever possible a
dimensioned sketch.
Avoid locating the terminal in close proximity to plastic materials
such as gutters or other combustibles. If this is unavoidable then a
suitable deflector should be made.
Some important requirements for a good functioning are:
The wall-mounted terminal has to be at a distance of at least
0.5 meters off:
- Corners of the building.
- Below eaves.
- Balcony's etc. unless the duct is dragged to the front side of the
overhanging part.
The roof mounted terminal has to be at a distance of at least
0.5 meters of the sides of the roof, excluded the ridge.
UK/IRL
12
Table Cadra Nova with interior MV150
Determine according to the table 4 the right total horizontal- and vertical length.
When meeting an X, and when the values are outside the table, the combination is not
allowed. Normally the 30 mm flue restrictor is preinstalled.
Misty with roundscreen
Determine according to the table 5 the right total horizontal- and vertical length.
When meeting an X, and when the values are outside the table, the combination is not
allowed. Normally the 30 mm flue restrictor is preinstalled.
0123456
0XXXXXXX
XXXXXX
XXXXX
XXXX
XXX
XX
X
XXXXX
0XX
0,5 X 0
1 X 30 0 0
000
1,5 40 30 0 0
2403000000
34040300000
4 50404030 0 0 0
5 505040403030 0
6 505050404030 0
7 605050404040
8 6060505050
960
60 60 50
10 65 60 60
11 65 65
12 65
X combination
not allowed
0 remove flue restrictor
Horizontal extension
Effective height
Number is size in mm
of the flue restrictor
table 5
interior Roundscreen
0123456
0XXXXXXX
XXXXX
60 XXXX
50 XXX
50 X X
40 X
0
0,5 X 0 X X X X X
1 30 0 0 0 0 X
240300 0 0 0 0
3 40 40 30 0 0 0 0
4 50404030 0 0 0
5 50 50 40 40 30 30 0
6 505050404030
7 6050504040
8 60605050
960
60 60
10 65 60
65
11 65
65
Horizontal extension
Effective height
X combination
not allowed
0 remove flue restrictor
Number is size in mm
of the flue restrictor
X
12
XX XXXX
table 4
interior Cadra Nova

Table 6
UK/IRL
15
UK/IRL
14
Dimension Terminal position Balanced flue room sealed
(kW input 7.5 kW expressed in net Natural draught
A Direct below an opening, airbrick, 300 mm
opening windows, etc.
B Above an opening, airbrick, 300 mm
opening window ect.
C Horizontally to an opening, airbrick, 300 mm
opening window etc.
D Below gutters, soil pipes or drain pipes 500 mm
E Below eaves 500 mm
F Below balconies or car port roof 600 mm
G From a vertical drain pipe or soil pipe 300 mm
H From an internal or external corner 600 mm
I Above ground roof or balcony level 300 mm
J From a surface facing the terminal 600 mm
K From a terminal facing the terminal 600 mm
L From an opening in the carport (e.g. 1200 mm
window into the dwelling
M Vertically from a terminal on the same wall 1500 mm
N Horizontally from a terminal on the same wall 300 mm
P From a vertical structure on the roof 600 mm
Q Above intersection with roof 500 mm
Flue terminal positions
fig. 3

UK/IRL
17
UK/IRL
16
4. INSTRUCTIONS FOR INSTALLATION
4.1 Gas connection
1. Installation pipes should be in accordance with BS 6891. Pipe work
from the meter to the appliance must be of adequate size.
2. The complete installation including the meter must be tested for
soundness and purged as described in the above code.
3. A means of isolation must be provide in the supply to facilitate
servicing.
4. The connection should be made in 8 mm copper or similar semi
flexible tube. (max 1 meter . Ensure that the gas pipe does not
interfere with the removal or replacement of the burner tray of the
controls.
5. The gas connection is nut and olive suitable for 8 mm pipe.
4.2 reparing the appliances Widescreen and Whisper
1. Open the ashtray door by pushing on the right side for the
Silence/Feeling and on the left side for the Whisper. Remove the
frame by loosening the screws A behind the door (see fig. 5 .
Lift and pull forward when you take it away.
A
C
B
gas supply routes when ire is itted in a deep surround
C = Through wall - Pipe must be sleeved and sealed to ire
A & B = Behind surround - Sleeve pipe through surround
inner wall
outer wall
cavity
surround
marble
Example of how terminal position is measured
3.2.2 Using an existing chimney as air inlet
You can connect the appliance onto an existing chimney. The existing
chimney then functions as air supply, where a flexible stainless steel
liner (to BS715 of 100 mm performs the flue function.
Requirements:
- Any existing chimney used as an air supply must only service this
appliance.
- A chimney that has previously been used for solid fuel must be swept
before use.
- The existing chimney needs to be airtight.
- The existing chimney needs to have an opening of
min. 150 x 150 mm.
- The chimney needs to be intact and well looked after.
- Use the adjustable roof-mounted-terminal especially made for this,
and the chimney connection set.
- The minimum distance between two terminals should be at least
450 mm.
fig. 4
fig. 5

UK/IRL
19
UK/IRL
18
4.2 reparing the appliances Widescreen and Whisper (continuing)
4. Take the box with the log set out of the combustion chamber.
5. Place the right flue restrictor in the combustion chamber. To
determine the right flue restrictor, see chapter 3.
C
C
C
C
C
C
C
C
C
C

fig. 8
fig. 9
4.2 reparing the appliances Widescreen and Whisper (continuing)
2.
Remove the back panel by loosening the screws B (see fig. 6 .
3. Remove the glass by removing the glass clamps C (see fig. 7 for
instance with a screwdriver. Careful when removing the glass! Wear
gloves! Before placing the glass back, be sure that there are no
fingerprints on the glass, it is not possible to remove those prints
after you burn the appliance or a while (they will be burnt in .
A
A
A
B
B
B
B
B
fig. 6
fig. 7

UK/IRL
21
4.3 reparing the appliance Misty (continuing)
4. Take the box with the log set out of the combustion chamber.
5. Place the right flue restrictor in the combustion chamber. To
determine the right flue restrictor, see chapter 3.

fig. 12
UK/IRL
20
4.3 reparing the appliance Misty
1. Remove the door frame. Lift and pull forward (see fig. 10 .
2. Open the ashtray door by pulling down (bottom handle .
3. To open the door, remove the screws C (see fig. 11 . The door
opening is limited; if you need more space then remove the door (lift
and pull forward . Be sure that there are no fingerprints on the glass.
It is not possible to remove those prints after you burn the appliance
for a while (they are burnt in .
fig. 10
C
C
C
C
fig. 11

UK/IRL
23
UK/IRL
22
4.4 reparing the appliances Spectra Nova/Cadra Nova (continuing)
4. Take the box with the log set out of the combustion chamber.
5. Place the right flue restrictor in the combustion chamber. To
determine the right flue restrictor, see chapter 3.

fig. 15
4.4 reparing the appliances Spectra Nova/Cadra Nova
1. To open the door, remove the screws A (see fig. 13 . Open and
remove the door; lift and pull forward. Be sure that there are no
fingerprints on the glass. It is not possible to remove those prints
after you burn the appliance for a while (they are burnt in .
2. Remove the back panel by loosening the 4 screws B (see fig. 14 .
fig. 13
fig. 14

UK/IRL
25
UK/IRL
24
4.5 Fitting the firebox (continuing)
8. Spread, the bags of embers (imitation ashes provide with the
appliance over the burner tray.
Attention! No embers on the grid end between the logs and the
burner tray.
9. Before placing the glass; check the glass sealing rope is in good
condition and makes an effective seal. Be sure that there are no
fingerprints on the glass. It is not possible to remove those prints
after you burn the appliance for a while (they are burnt in .
- Widescreen and Whisper; Place the glass in front of the appliance
and fix it with the glass clamps. Replace the frame.
- Misty, Cadra Nova and Spectra Nova:
Place the door and fix it. Check on visual leakages around the
door sealing.
10. Misty and widescreen: Fix the back and top or door frame (the back
frame first .
ceramic blanket
ceramic
blanket
ceramic
blanket
ceramic
blanket
ceramic 
blanket

4.5 Fitting the firebox
Points of attention for placement:
- If possible, first locate the appliance before assembling the flue.
- If this is not possible then always use an extendible pipe before
connection onto the appliance.
1. Position the firebox in the fireplace opening. You can adjust the
height with the 4 adjustable feet.
2 Make the gas connection according to the instructions (also see gas
connection, chapter 4.1 .
3. Assemble the flue system onto the firebox (see chapter 5 .
4. Check if applicable that the safety hatch seals the combustion
chamber properly.
5. If necessary, place the DC convection system (also consult the
instruction belonging to the DC construction set .
6. Isolate the firebox with a ceramic blanket (25 mm . Preferred choice
for insulation is unbound insulation wool (at 1000 °C gives no
smell .
7. Place the log set (see placing log set, chapter 4.4 .
sa ety hatch
fig. 16
fig. 17

UK/IRL
27
UK/IRLUK/IRL
5. INSTALLATION OF THE FLUE
5.1 Connections with use of concentric duct material
- Build the system starting from the appliance on.
- Make a hole of ø 153 mm for the wall or roof mounted terminal.
- Make sure you place the pipes in the right direction, the narrow
end towards the appliance.
- Make sure the pipes are fixed sufficiently, a wall clamp every 2m, so
the weight of the pipes is not resting onto the appliance.
- The outside of the pipe can become hot (140 degrees . Stay 50 mm
away from wall surface or sealing. Make sure to provide sufficiently
heat resistant isolation when going through the wall or roof.
- Because of expansion or cooling down the concentric pipes can turn
loose. It is recommended to fix the spring clip with a self tapping
screw at inaccessible places.
- To get the exact measure flue length you can use cut down-
concentric pipe, wall mounted terminal or roof mounted terminal. To
obtain a smoke sealed connection, the inner pipe must be 20 mm
longer then the outside pipe.
- The horizontal pipes need to rise away from the appliance at a rate
of 3 degrees per metre.
UK/IRL
26
4.6 lacing the log set
Never place extra elements of any kind into the combustion chamber.
To guarantee good combustion, the log set may only be installed in
the way specified by Faber International. Any other arrangement can
lead to soot on logs or window. Do not use the fire with broken or
missing logs.
4.6.1 lacing the log set Widescreen, Whisper, Spectra Nova, Misty and Cadra Nova
On the bottom of the logs is a identification:
• L location on the left side resting on the rear log.
• R location on the right side resting on the rear log.
• 1 dimple first log left placed over the burner and resting on the
burner tray.
• 2 dimples placed in the middle over he burner and resting on the
burner tray.
• 3 dimples the right side log placed over the burner and resting on the
burner tray.
Attention! Beware that there are no embers between the logs and the
burner tray.
fig. 18
fig. 19

UK/IRL
29
UK/IRL
28
UK/IRLUK/IRL
5.2 Connection onto an existing chimney (continuing)
5. Fixing the chimney sealing plate (D and place the 150 mm
grommet into the hole of the sealing plate.
6. Fix the sealing plate air tight into the builders opening (use the
isolation rope from the chimney connection set to make the plate
air tight .
7. Slide the pipe (E 150mm length 500mm into the sealing plate.
Slide this pipe so far that you will have enough space later on
for assembling the liner.
8. Install the appliance.
9. Connect the flexible stainless steel liner onto the appliance using
the 100mm pipe (F as adapter.
10. If the distance from the flue outlet to the sealing plate is bigger
then 300 mm, you have to use a concentric pipe first.
11. Slide the outside pipe onto the appliance or concentric extension
so that you have a air tight connection.
UK/IRLUK/IRL
5.2 Connection onto an existing chimney
You can connect the appliance onto an existing chimney. The existing chimney then
functions as air supply, where a flexible stainless steel liner (to BS715 of 100 mm
performs the flue function. Any existing chimney used as an air supply must only
service this appliance.
Requirements:
- 300 mm of free space above the appliance;
- The chimney only supply’s air to this appliance;
- The existing chimney needs to be clean and very well swept;
- The existing chimney needs to be airtight;
- The existing chimney needs to have an opening of
min. 150 x 150 mm.
Parts needed for this kind of installation:
- Chimney connection set
part number A9225000 Fig 20 part D
- Short roof terminal
part number A9266100 Fig 19 part B
- Chimney closure plate
part number A 9240000 Fig 19 part A
- Two stainless steel tubes one 100 mm -
length 500 mm and one 150 mm -
length 500 mm
part number A 9273900 Fig 19 part E and F
1. Place the aluminium closure plate (A onto the
chimney. Permanently attach and make airtight.
2. Pull the liner (C through the chimney.
3. Connect the liner onto the roof terminal and fix
this with the clamp provided with the chimney
connection set.
4. Place the roof terminal onto the closure plate.
F
E
D
C
B
A
fig. 20

UK/IRL
31
UK/IRL
30
UK/IRLUK/IRL
3. Connect the wires to the gas valve (see fig. 22 .
4. Check that there are batteries in the transmitter.
See "Replacing batteries", see chapter 10.4.4.
5. Set the on/off switch on the receiver to "on".
Setting the right transmission code
The receiver has to learn the code from the transmitter, which is already
done at the factory. However the code disappears if the receiver is
disconnected from the mains for a longer period.
1. Push the "mod" button on the receiver and hold it for 3 seconds.
2. The green control lamp will light up and stay on. Repeat this step
if it doesn't.
3. Push a button on the remote control. The control lamp on the
receiver should now go out.
4. Again push a button on the remote control. The lamp starts
flashing and will switch off eventually.
5. The receiver now recognizes the remote control. The remote
control now functions.
6. Check if you can hear a sound and the motor runs when you
push a button on the remote control.
fig. 22
UK/IRLUK/IRL
5.3 Remote control (if applicable)
The remote control is only meant to regulate the flames, it functions
only when the pilot burner is ignited. It is therefore not possible to
ignited the appliance with the remote control or to shut-off the pilot-
flame.
The radio-frequency remote control is intended for fireplaces installed
in a domestic setting in all EU countries except Austria, Denmark,
Finland and Greece.
Features:
- Manual control will always remain possible.
- The remote control is a radio frequency type and has been approved
internationally.
- The remote control generates a unique safety code every time you
activate the transmitter, its similar to those used in a car.
- The remote control is easy to install retrospectively.
5.3.1 Installation remote control
1. Connect the mains adapter to the receiver box. The adapter is set
to the correct voltage in the factory 4.5V.
2. Slide the receiver box into the holder.
fig. 21

UK/IRL
33
UK/IRL
32
UK/IRLUK/IRL
6.3 Functional balanced flue check
1. Set the appliance on max. input.
2. Verify the flame picture, this means no flames against the
window, the flame have to come besides the logs, if not check
the log layout.
3. Check if the flames are yellow after 10 minutes of operation. If
you still have a blue flame or the appliance goes out check:
- If the flue pipes are fitted correctly (no leakage .
- If the wall mounted terminal is placed with the correct side up.
- If the correct flue restrictor is installed.
6.4 Check reference pressure
The appliance is preset to give the correct heat input.
No further adjustment is necessary. Fit a pressure gauge at the test
point D to check the burner pressure.
The pressure should be checked with the appliance alight and at max
input.
The setting pressure should be as shown at the technical data
page 41.
After checking the pressure, turn off the appliance. Remove the
pressure gauge and close the sealing screw. Re-light the appliance.
Turn to max. input and test around the test point D for gas
soundness using a suitable leak detection fluid.
C D
DC
AB
BA
fig. 24
UK/IRLUK/IRL
6. COMMISSIONING (functional checks)
6.1. Check pilot ignition
1. Push in and turn the control knob (A from {anticlockwise to the
setting (small flame . You will hear a tick meaning there is
ignition. Hold the knob in and wait for a few seconds while the air
is purged.
2. Bring the knob back in the start position and turn the knob several
times to the position. Check that the pilot has lit.
3. Continue to hold in the control knob for a further ten seconds to
ensure that the pilot flame is stable.
4. Release the knob. The pilot should remain alight.
6.2 Functional burner check
1. Turn knob (B to max. clockwise.
2. Turn the knob (A more anticlockwise to the position (large
flame . Now it is possible to light the main burner.
3. Turn knob B anticlockwise to max. The main burner should light.
Check for gas soundness at all joints with leak detection floud!
4. Check the ignition of the main burner on low and high setting.
5. Turn knob B clockwise till {. The main burner is off.
6. Turn the knob A to {. The pilot should go out.
AB
fig. 23

UK/IRL
35
UK/IRL
34
8. SERVICING
To ensure safe, efficient operation of the appliance, it is necessary to
carry out routine servicing at regular intervals.
It is recommended, that the fire is inspected/serviced by a competent
person at least once a year.
Important
Turn off the gas supply before commencing any servicing. Always
test for gas soundness after refitting the appliance.
8.1 Routine annual servicing
1. Clean (if necessary :
- the pilot system;
- the burner;
- the combustion chamber;
- the glass.
2. Check the log lay and replace the embers (if applicable .
3. Do the functional test as described at page 34.
4. Check the flue system and terminal on damage and soundness
(visual inspection .
UK/IRLUK/IRL
7. HANDING OVER
(final check and customer briefing)
7.1 Instruct the customer on the full operation of the appliance.
7.2.1 Advise the customer how to clean the appliance including the
glass.
7.2.2 Instruct the customer on the operation of the remote control,
including replacement of batteries and how to set the right
transmissions code.
7.2.3 Hand over these instructions including the user guide to the
consumer.
7.2.4 Recommend that the appliance should be serviced by a
competent person at least once a year.

UK/IRL
37
UK/IRL
36
8.1.4 Burner tray assembly
1. Remove the front, glass, log set, grid and burner tray cover.
2. Break the gas supply at the control valve.
3. Unscrew the burner assembly and take them out of the combustion
chamber.
A. Pilot assembly
B. Burner
C. Fixation plate
D. Injector
E. Gas control
F. Receiver
8.1.5 ilot/thermocouple assembly
Remove the burner tray as described above.
Now you have access to all the pilot and thermocouple parts.
fig. 25
A
B
C
D
E
F
8.1.1 Cleaning the glass
Depending on the intensity of use, you can get a deposit on the
glass. This can be removed with a special ceramic glass cleaner
(ceramic cook-top cleaner as follows:
1. Remove the front and the back.
2. Clean the glass. Handle the glass with clean hands, wear gloves if
possible.
3. To fit the glass, proceed in reverse order. Make sure that the log
set has been installed correctly before fixing the glass.
Attention:
Before placing the glass: check the glass sealing rope is in good
condition and makes an effective seal. Be sure that there are no
fingerprints on the glass. It is not possible to remove those prints
after you burn the appliance for a while (they are burnt in . Place
the glass in front of the appliance and fix the glass frame or use the
glass clamps.
8.1.2 Cleaning the combustion chamber and burner
You can clean the combustion chamber with a vacuum cleaner.
If the burner is visibly damaged, this can affect the distribution of
the flame, if so then replace the burner.
8.1.3 ropane conversion
For conversion from propane to natural gas, order for a propane
burner unit.
Please give the serial number from the data plate when you order.