FALCON RIDGE HO-P500-FC04 Installation manual

2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of Honda Pioneer 500
Full Cab with Aero-Vent Windshield
HO-P500-FC04
CAUTION: Do not smoke inside the cab or expose the enclosure to direct flames. Product is FLAMMABLE.
Be sure to read these instructions thoroughly before opening and installing. The installation is best done
when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if conditions
prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature prior to
installation.
1. This cab enclosure is made up of 4 different panels that all come together to enclose the sides and rear of
the vehicle. You may put on different pieces or leave other pieces off to create the enclosure that best
meets your needs.
2. Check over the parts included in the carton with the parts list shown below:
Velcro hook strips 16 each 3” long
Velcro hook strips 4 each 6” long
Velcro hook strips 2 each 9” long
Velcro hook strips 2 each 34” long
Velcro hook strips 1 each 38” long
Webbing Straps w/Loop 2 each
Webbing Straps w/ Grommets 2 each
Webbing Straps w/ Velcro 2 each
Screw snaps 13 each (1 extra)
Cab enclosure 4 Pieces
If any parts are damaged or missing please contact customer service at [phone].
3. For these instructions we will be installing the entire enclosure. This will cover every piece so if you
should want to install just parts of the enclosure these instructions should be sufficient. The order of
installation will be as follows:
a. Side Door Panels
b. Rear Window
c. Top
Door Panels:
4. Begin installation by hanging the Door Panels from the top by using the 3” adhesive Velcro strips as
shown in the photos on the next page:

5. Begin installation of the Door Panels by hanging them from the Double-Sided Strips along the top of the
doors. Hold the door up and mark where the each strip is and wrap a 3” adhesive strip around the roll
cage. Now hang the door up and it will be in place to install the rest of the Velcro for the door. See
Photo Below:

6. Now move around the door and attach the remaining Velcro strips in the same manner. Down the front
of the door place the edge of the door against the side of the windshield and run the Velcro strips under
it with the 3” adhesive Velcro on the inside of the roll cage.
7. The rear of the door panel has 4 double-sided Velcro tabs that attach to the rear bar. For these you will
take the two 6”, 9", 10", and 15" adhesive Velcro strips and attach them down the rear bars facing the
rear of the vehicle. Then attach the tabs to the bar as shown below.
8. Once the upper portion of the doors are in place it’s time to place the snaps around the bottom portion of
the doors.

9. Next take the front of the door and tuck it inside the vehicle. There are three snaps that will go on the
inner panel. NOTE: it helps to place the screw snaps into the sockets on the cabs first, then starting at the
top one, push them into the plastic so a small dimple is left behind. Then pull the screw snap back out
and screw it into the plastic where the mark was made. See photo on next page.
10. Next do the same for the three snaps along the bottom rear corner of the door as shown in the photo
below.

Rear Window:
11. Begin installation of the Rear Window by hanging it from the top bar first. Take the 38” adhesive
Velcro strip and attach it to the top bar facing towards the front of the vehicle. The photo below shows
where to install the Velcro.
12. The sides of the Rear Panel will attach to the outside of the double-sided tabs that hold the rear of the
door panels as shown below.
13. The bottom of the Rear Window is held in place by magnets
Top Cap:
14. To install the Top you first need to attach four straps to you vehicle that will hold the top on. The two in
the front of the vehicle attach to the bottom windshield clamp as shown in the photo below.