FALCON RIDGE AC-PRO-WD05 Installation manual

2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of Arctic Cat / Textron Prowler Pro
Full Aero-Vent Polycarbonate Windshield
AC-PRO-WD05
NOTICE: Please check contents of package for any damage and make sure all parts fit correctly and you
are happy with the product before removing protective film. Once the film is removed you cannot return
the product for a full refund.
Be sure to read these instructions thoroughly before opening and installing the windshield.
1. Check over the parts included in the cartons with the parts list shown below:
1 ¼” Stainless Bolts 4 each
1 3/4” Stainless Bolts 2 each
2" Stainless Bolts 2each
Small Washers 8 each
Metal Brackets 4 each
Plastic Thumb Nuts 4 each
Lock Nuts 4 each
Nylon spacers 2 each
1 ¼” Black Spacer 2 each
Plastic Slide Fasteners 14 each
167" side Bulb Gasket 1 each
Small Polycarbonate piece 1 each
Vent Sliders 2 each
If any parts are damaged or missing please contact customer service at [phone].
2. Start by pulling it out of the box; find a clean area to lay it down and install the hardware.Next take the
136” Side Bulb rubber gasket and starting at one end firmly place along the bottom edge of the
windshield.You will need to peel back the protective film from the edge to install the gasket. If you
leave the bulk of the protective film on while installing you can avoid scratching the windshield. Ensure
that the gasket is seated fully home on the along the edge to insure a good fit of the windshield.
3. Next take the two vent sliders and install then to the inside surface of the windshield. Start by installing
the handle first. Take the 2” bolt, black spacer and lock nut and install them into the round holes on the
sliders. Make sure that the bolts are installed on opposite sides of the sliders so that you have mirror
images of each other when done. The pictures on the next page show how to install the bolts.

4. Then place the sliders on the windshield so that the pointed ends are facing towards the outside edges.
Place the plastic slide fasteners into the slots on the sliders and into the holes on the windshield to finish
installation. See photo on the next page.

5. Before installing the windshield place the small polycarbonate piece on the inside of the windshield
along the top center as shown in the photo below. This piece will hold the middle of the windshield
against the frame.

6. Now place the windshield inside the frame of the Prowler Pro.Take the Metal brackets and bolt them to
the windshield from the inside using the supplied 1" bolts washer and thumbnut as shown in the picture
below.
7. Enjoy, and remember- when cleaning the windshield do so gently at first with warm water and mild
detergent to dislodge any grit that may scratch the Polycarbonate. After rinsing and drying with a soft
cloth, you may then polish the windshield with an appropriate commercially available plastic polish,
also available from Falcon Ridge. This will ensure many seasons of clarity and keep scratching and
swirling to a minimum. Never use cleaners such as Windex that contain ammonia as doing so may
adversely affect the windshield.

Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within 30 days from date item is
received. You MUST package the product exactly as it was originally packaged from the factory to get a
full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the
windows on top of each other with the canvas folded in between and the paper (if available) on both sides of the
windows.
All returned products will be inspected upon arrival at the production facility and must be in unused,
factory new condition to receive refund - a 25% restocking fee will apply.
If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number, use our
preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying
the shipping to return the item.) Any returns submitted to Falcon Ridge without a return authorization
number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you
must first call them and see what their return policy is. Once your item reaches our production facility, our
customer satisfaction team will inspect your item to ensure unused, factory new condition. NOTE: All
windshields must be returned with the original protective film intact and not removed. Do NOT
REMOVE if you have any intentions of returning the item. Refund/ replacement of a windshield will only
be processed on items with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect them during transit and ensure your
returned item arrives back factory fresh, and in new resalable condition (any returned items that have been
used, altered or damaged in any way will not be subject for a refund.) All contents including instruction
manuals, accessories, hardware, Velcro, etc. must be included in your return shipment. Only items in OEM
factory new condition will be approved. Once returned items are received, credit will be issued to the original
credit card/ payment method used for the purchase. Outbound shipping and return shipping cost will not be
refunded. Please allow 4 to 6 weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or Windshields! Below are the
terms under which your product is covered under our manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure, tops and/or windshield due to
defect of the product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will gladly correct
the problem or replace the enclosure, tops &/or windshield. Upon submitting for the correction or replacement
we will need to receive pictures of the defect in material or workmanship along with the receipt from the date of
purchase.