Falcon RW Series User manual

*030388-000-70*
030388-000-70
© Allegion 2014
Printed in U.S.A.
030388-000-70 Rev. 10/14-d
Customer Service
1-877-671-7011 www.allegion.com/us
Mounting and Rehanding Installation Instructions
RW Series
Retrot Lever Trim
STEP ONE:
Remove all existing trim from door,
including cylinder if one is installed.
STEP TWO:
Insert inner and outer spindles into lock hubs.
NOTE: Because of various hub sizes, be sure
spindles fit properly. Place the enclosed template
over the spindle. Align with door edge and mark the
four (4) thru-bolt hole locations. This should be done
to both sides of the door. Drill the four (4) holes
halfway through from each side of door.
IMPORTANT: It may be necessary to enlarge the
trim hole due to varying door preps. Falcon retrofit
trim requires both sides to be 1¹⁄₈” diameter
minimum to clear trim mechanism.
STEP THREE: Before mounting the trim, be
sure to insert spindle springs into each
lever. With spindle in outer hub, place outer
trim over spindle with posts going into thru-
holes. Place inside trim over spindle and
install the four (4) mounting screws. Before
screws are tightened, check to see that
both levers are operating properly. If
reinstalling the cylinder, determine if a
blocking ring is required. Tighten set screw
then check cylinder for proper function.
Tighten the four (4) trim mounting screws.
REPLACEMENT PARTS
Spindle
Spindle
Adapter
Spring
P/N 021242–001–30
P/N 030329–000–30
P/N 030319–000–30
P/N 021244–001–60
5/16”
9/32”
5/16”
5/16”
3/8”
SPINDLE
TEMPLATE
SCREW
6-32x1¹⁄₄”
INSIDE
SPRING
SPINDLE
SPRING OUTSIDE
TRIM HOLE

2
R
R
R
L
L
R
R
R
L
L
R
R
L
L
R
R
L
L
R
R
L
L
R
R
L
L
R
R
L
L
1. Holding lever as shown,
bend tab of lockwasher back flat. Remove nut.
2. Holding lever securely, rotate
rose assembly clockwise slightly, and remove plate and lockwasher.
3. Using caution, allow rose
assembly to rotate counter- clockwise to relieve spring tension.
4. Remove spring and reinstall
with spring hook on opposite side of post.
5. Holding lever securely,
rotate rose assembly counterclockwise slightly past 90 deg.
6. Reinstall plate with "L" side
up and in line with "L" on rose assembly.
7. Reinstall lockwasher and nut.
Tighten nut and then back off slightly until rose assembly rotates freely under plate. Bend up one tab of lockwash- er against nut.
RE-HANDING INSTRUCTIONS FOR FALCON RW SERIES LOCK TRIM
Example shown is a right hand being changed to a left hand
Reverse sequence to change from left to right hand
Note: Inside trim is always opposite the outside trim LH/LHR RH/RHR
VIEWED FROM OUTSIDE
R
R
L
L
L

8.500
3.670
Additional Notes: Revision History Revision Description:
D > Revised artwork
1. None A B C D E F
4955-255 0790 6683
Material
White Paper
Edited By Approved By EC Number Release Date
J. Ellis M. Roberts xxxxx 10/14
Notes
1. printed two sides
2. printed black
3. tolerance ± .13
4. printed in country may vary
5. drawings not to scale
Title
RW Series Retrot Lever Trim
Creation Date
10-22-14
Number
030388-000-70
Revision
D
Created By
J. Ellis Activity
3899 Hancock Expwy
Security, CO 80911 © Allegion 2014Software: InDesign CS6
8.500
11.000
BEGINNING SHEET FOLDED SHEET
FRONT
FRONT