Falcon DOMINATORPLUS E3512 User manual

E3512 and E3532
DOMINATORPLUS Grills
USERS INSTRUCTIONS
SECTION 1 - GENERAL DESCRIPTION
SECTION 2 - CONTROLS and OPERATION
SECTION 3 - COOKING HINTS
SECTION 4 - CLEANING and MAINTENANCE
This appliance has been CE-marked on the basis of compliance with the Low Voltage and
EMC Directives for the voltages stated on the data plate.
The appliance MUST BE installed by a competent person in compliance with the INSTALLATION AND
SERVICING INSTRUCTIONS and National Regulations in force at the time.
UK regulations are listed on the front of the Installation and Servicing Instructions.
Regular servicing by a qualified person is recommended to ensure the continued safe and efficient
performance of the appliance.
WARNING - THE APPLIANCE MUST BE EARTHED.
Upon receipt of the User's Instruction manual, the installer should instruct the responsible person(s)
of the correct operation and maintenance of the unit.
This equipment is ONLY FOR PROFESSIONAL USE, and shall be operated by QUALIFIED persons.
It is the responsibility of the Supervisor or equivalent to ensure that users wear SUITABLE
PROTECTIVE CLOTHING and to draw attention to the fact that, some parts will, by necessity, become
VERY HOT and will cause burns if touched accidentally.
Upon receipt of the User's Instruction manual, the installer should instruct the responsible person(s)
of the correct operation and maintenance of the Appliance. This equipment is ONLY FOR
PROFESSIONAL USE, and shall be operated by QUALIFIED persons. It is the responsibility of the
Supervisor or equivalent to ensure that users wear SUITABLE PROTECTIVE CLOTHING and to draw
attention to the fact that, some parts will, by necessity, become VERY HOT and will cause burns if
touched accidentally.
WEEE Directive Registration No. WEE/DC0059TT/PRO
At end of unit life, dispose of appliance and any replacement
parts in a safe manner, via a licenced waste handler.
Units are designed to be dismantled easily and recycling of all
material is encouraged whenever practicable.
Falcon Foodservice Equipment
HEAD OFFICE AND WORKS
Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.
SERVICELINE CONTACT
Phone: [phone] Fax: [phone]
T100788 Ref.2

SECTION 1 -
GENERAL DESCRIPTION
All models are supplied with nickel plated wire grid shelf
(for multi-angled operation), drip tray, drip trough and
close ribbed reversible cast aluminium brander.
The drip tray must be located in position at all times when
the grill is in use.
This manual covers operation of the following units:
E3512 Model
Brander Size: 460mm wide x 410mm deep
E3532 Model
Brander Size: 540mm wide x 275mm deep
SECTION 2 -
LIGHTING and OPERATIONS
E3512 Model
The elements are controlled by an energy regulator which
supplies infinitely variable heat.
E3532 Model
The element is controlled by an energy regulator which
supplies infinitely variable heat.
Pre-heat
When using brander for cooking steaks etc., the grill
requires a pre-heating period from cold of approximately
45 minutes. Set energy regulator to full heat to reach
maximum temperature. Toast and similar items may
however, be inserted five or ten minutes after switching
on, cooking on the wire grid.
Drip Tray
The drip tray must be in position at all times when grill is
in use.
Cooking on the Grid
The grid can be used in any of the runner positions.
Toasting
For toasting bread, place grid on second runner position
from top of E3512 model and in top position of E3532.
Full heat must be maintained throughout and the entire
grid surface below the elements can be used.
Browning
For browning tops of dishes, place dish upon grid and
position to suit dish height. Adjust controls as required.
Cooking on the Brander
The brander is double sided, located on top of wire grid .
It can be used in any runner position from second top
downward.
It can be inserted level when batches of steaks are to be
cooked to the same degree or it can be sloped
downwards from rear to front to enable a number of
steaks etc. to be cooked to varying degrees at the same
time.
For this method of cooking, it is recommended that
brander support grid is inserted in runners two and five
from the top. When using the fully heated brander, it is
not necessary to turn food. The drip trough is located over
the two upstanding pins on wire grid when using brander.
Empty trough regularly to prevent spillage, taking care
with hot fat.

SECTION 3 - COOKING HINTS
GRILLING is a QUICK, SIMPLE and DIRECT method of
cooking. Ideal for a wide and varied list of menu items,
heat is transferred from the source in direct rays
(radiation) on to the food requiring to be cooked.
These foodstuffs can be placed on trays or alternatively,
directly on the brander.
10kg is the maximum recommended brander load for
safe use.
DUE TO DIRECT HEAT PRESENT DURING GRILLING,
GREAT CARE SHOULD BE TAKEN WHEN COOKING
FOOD. BE CAREFUL OF SPLASHES FROM HIGH FAT
CONTENT FOODSTUFFS.
EMPTY DRIP TRAY AND TROUGH FREQUENTLY.
USE OF TONGS IS RECOMMENDED WHEN TURNING
OR MOVING FOOD.
SECTION 4 -
CLEANING and MAINTENANCE
Warning
Before cleaning, switch off and disconnect from mains.
The appliance must not be cleaned with a jet of water or
steam cleaned.
Daily Cleaning
Vitreous Enamel
Wash thoroughly with warm soapy water.
Aluminium Brander
Brander should be left under full heat. This will, after a
period, carbonise spillage. Clean with a wire brush.
Wire Grid Shelf
Soak grid shelf in hot soapy water, rub with pan scrubber
on stubborn stains.
Stainless Steel Sides and Drip Tray
Wash with warm soapy water. A mild detergent on a cloth
can be used to remove stubborn stains. Always rub along
in grain direction, rinse with clean water and dry with a
clean cloth. The drip tray should be cleaned out of all fat
and debris before steeping in hot soapy water. Rinse in
clean water and dry with a clean cloth.
Cleaning - Important Note
Do not use proprietary cleaners, especially those which
may have a high caustic content on the vitreous
enamelled surfaces of this unit (i.e. drip tray).
This is particularly important when unit is hot.
Such cleaners can cause serious damage or
discolouration to the enamel finish and only a soap or
detergent solution should be used.
SECTION 5 - SPARES
The following parts may require replacing during unit life.
Elements
Energy Regulator
Relay
Neon