Fanimation Palmetto User manual

The Palmetto
MODEL NOs: FP601 –5**
OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS

WARNING
DO NOT INSTALL OR USE FAN SYSTEM IF ANY PART IS DAMAGED OR MISSING. THIS
PRODUCT IS DESIGNED TO USE ONLY THOSE PARTS SUPPLIED DESIGNATED
SPECIFICALLY FOR USE BY FANIMATION. SUBSTITUTION OF PARTS OR ACCESSORIES
NOT DESIGNATED FOR USE BY FANIMATION COULD RESULT IN PERSONAL INJURY OR
PROPERTY DAMAGE. CONTACT FANIMATION FOR MISSING OR DAMAGED PARTS.
[phone]
OR
[phone]
MAINTENANCE AND BLADE CLEANING
PERIODIC CLEANING IS RECOMMENDED USING A SOFT BRUSH OR LINT FREE CLOTH.
ABRASIVE AND/OR NON-ABRASIVE CLEANING AGENTS ARE NOT REQUIRED AND
SHOULD BE AVOIDED TO PREVENT DAMAGE TO FINISH. ALSO LIGHT DUSTING OF THE
SELECTED BLADE IS RECOMMENDED. A FEATHER DUSTER WILL WORK BEST.
PERIODICALLY TIGHTEN SET SCREWS ON SHAFT ADAPTERS (P608MAC AND P610MAC),
BLADE HUBS TO SHAFT SCREWS AND HUB TO BLADE STEMS.

1. LOCATE POWER
a. POWER IS SUPPLIED BY PURCHASER/CONTRACTOR
b. DISCONNECT POWER SUPPLY AT BREAKER BOX.
c. A SINGLE PHASE 220 TO 240VAC ELECTRICAL FEED LOCATED AT THE CENTER OF THE MOTOR ASSEMBLY
(P680M**)
d. A SINGLE PHASE 220 TO 240VAC ELECTRICAL FEED LOCATED AT THE CENTER OF THE MOTOR ASSEMBLY
(P680M**)
e. A SINGLE PHASE ELECTRICAL FEED IS REQUIRED
f. MOTOR IS SINGLE SPEED ONLY
g. DO NOT OPERATE WITH ANY SPEED CONTROL
2. INSTALLATION NOTE
a. IT IS RECOMMENDED THAT EACH CEILING MOUNT ASSEMBLY (P680M**, P600S**, AND P600D** IF REQUIRED)
HAVE ¾” PLYWOOD BACKING SECURED TO A STRUCTURAL MEMBER FOR ADEQUATE SUPPORT.
3. MOUNT MOTOR ASSEMBLY OVER POWER SUPPLY TO COVER JUNCTION BOX.
a. MARK FOUR MOUNTING HOLE POSITIONS AS REQUIRED
b. DRILL PILOT HOLES
c. START 2 SUPPLIED LAG BOLTS WITH WASHER IN THE OUTSIDE HOLES
d. DO NOT COMPLETELY TIGHTEN LAG BOLTS AT THIS TIME
e. CONNECT THE MOTOR WIRES TO THE SUPPLIED LEADS
i. BROWN TO “HOT”
ii. BLUE TO “NEUTRAL”
f. POSITION MOTOR ASSEMBLY OVER THE FINAL TWO PREDRILLED HOLES AND FASTEN WITH REMAINING LAG
BOLTS AND WASHERS
g. SECURE ALL FOUR LAG BOLTS
4. LOCATE POSITION OF EITHER END OR CENTER ASSEMBLY (P600S** OR P600D**)
a. MAXIMUM DISTANCE FROM MOTOR TO NEXT ASSEMBLY IS 9’11” CENTER OF BASE TO CENTER OF BASE OR
b. MAXIMUM DISTANCE FROM MOTOR TO NEXT ASSEMBLY IS 10’5” FROM OUTSIDE EDGE OF BASE TO OUTSIDE
EDGE OF BASE.
c. MARK FOUR MOUNTING HOLE POSITIONS AS REQUIRED
d. DRILL PILOT HOLES
e. MOUNT NEXT ASSEMBLY IN DESIRED LOCATION AND TIGHTEN ALL FOUR LAG BOLTS SECURELY
f. MEASURE DISTANCE FROM INSIDE EDGE OF COUPLER ADAPTER TO INSIDE EDGE OF COUPLER ADAPTER TO
DETERMINE LENGTH OF ROTATING SHAFT (TUBE108**)
g. CUT ROTATING SHAFT (TUBE108**) TO MEASURED LENGTH.
h. ON SECOND ASSEMBLY LOOSEN THE TWO LAG BOLTS ON THE INSIDE EDGE OF THE BASE ENOUGH TO LEAN IT
BACK.

i. INSTALL DESIRED NUMBER OF HUB ASSEBMLIES (P606**) ON THE ROTATING SHAFT (TUBE108**)
j. SPACE HUBS (P606**) ALONG ROTATING SHAFT AS DESIRED AND SECURE WITH SET SCREWS
k. INSERT ROTATING SHAFT IN THE MOTOR END COUPLER AND TIGHTEN SET SCREW.
l. LEAN BACK SECOND ASSEMBLY AND INSERT ROTATING SHAFT (TUBE108**) INTO THE COUPLER ADAPTER.
m. TIGHEN LAG BOLTS SECURELY ON THE BASE
n. TIGHTEN SET SCREW ON COUPLER ADAPTER.
5. IF YOU ARE INSTALLING ADDITIONAL SECTIONS REPEAT STEP 4 FOR EACH
a. BE SURE THAT THE MIDDLE ASSEMBLIES ARE P600D** AND THE FINAL ASSEMBLY IS THE P600S**
6. INSERT BLADE ASSEMBLY STEM INTO HUB ASSEMBLIES AND SECURE WITH SETSCREWS.
a.
7. CHECK THAT HUBS, BLADE STEMS, BLADES AND ROTATING SHAFT (TUBE108**) SETSCREWS ARE SECURE
8. RESTORE POWER TO SYSTEM.