Fantech FADE User manual

Installation Instructions for
Model FADE
FADE Installation Manual 1
Installation
1. FADE units can be mounted at any angle for exhaust ventilation. When planning installation, allow adequate space for blower removal for
service or inspection.
2. Because this unit has rotating parts, safety precautions should be exercised during installation, operation and maintenance.
3. CAUTION: “For General Ventilation Use Only. Do Not Use To Exhaust Hazardous Or Explosive Material and Vapors.”
4. Remove unit from package and inspect within 10 days after receipt. If damaged, report damage to carrier. Do Not operate this unit with
visible damage to the blower or impeller assembly.
5. Ensure centrifugal impeller has free rotation. If impeller hits orifice, check screws holding motor bracket. Tighten all screws before operat-
ing unit. WEAR HAND PROTECTION AND STAY CLEAR OF SHARP EDGES.
6. Screen guards must be installed when fan will be within reach of personnel, within (7) feet of the working area, or when advisable for safety.
7. When mounting fan, the inside dimension of the opening should correspond to dimension “D” possibly allowing an extra 1/4”. When using a
louver or damper, provide adequate framing depth to accommodate the fan.
Warnings
DO NOT CONNECT POWER SUPPLY until fan is completely installed. Make sure electrical service to the fan is locked in “OFF” position.
1. All units are suitable for use with solid-state speed control.
2. WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS – OBSERVE THE
FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact your manufacturer's
representative.
b. CAUTION: Before installation, servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent
warning device, such as tag, to the service panel.
c. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and
standards, including fire-rated construction.
d. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent
back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire
Protection Association (NFPA), and the American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
e. When cutting or drilling into wall and ceiling, do not damage electrical wiring and other hidden utilities.
f. Ducted fans must always be vented to the outdoors.
g. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI
(Ground Fault Circuit Interrupter) - protected branch circuit.
h. NEVER place a switch where it can be reached from a tub or shower.
3. WARNING! Check voltage at the fan to see if it corresponds to the motor name plate.
READ & SAVE THESE INSTRUCTIONS!

2 FADE Installation Manual
Dimensions
Model A B C D1 D2 E F G Blade Type
FADE 8 125/16 2 101/473/481/16 1/4– – S
FADE 10 149/16 2 125/810 105/16 1/4– – S
FADE 12 17 3 15 12 127/85/16 21 151/2S
FADE 14 193/16 31/8171/814 153/85/16 21 151/2S
FADE 16 223/431/221 161/2171/43/824 161/2S
FADE 18 229/16 41/421 18 181/23/824 161/2A
FADE 20-6 253/16 41/2241/420 201/23/826 171/2A
FADE 20-4 253/16 41/2241/420 201/23/826 171/2A
FADE 22 285/851/4269/16 22 221/23/832 183/4A
FADE 25 313/46 291/225 251/23/832 183/4A
All dimensions in inches. FADE 12 through FADE 25 Fans can be ordered fully assembled with housing and damper. See Fantech Price List for
detailed descriptions and model numbers.
C
AF
E
G
B
D1
D2
C
AF
E
G
B
D1
D2
FADE A-TYPE
“Fan Only” Model
FADE A-TYPE
“Fully Assembled” Model
FADE S-TYPE
“Fan Only” Model
FADE S-TYPE
“Fully Assembled” Model

Contactor for 3-Phase Fans, 208-230/460v
FADE Installation Manual 3
Wiring
SPECIAL WIRING PRECAUTIONS:
All installation should be wired according to the following diagrams. Failure to comply will cause the motor to "hum" or not work.
All units are pre-wired, just bring incoming supply into marked ports on terminal strip. (EXCEPT FOR 3 PHASE UNITS, please use a motor con-
tactor & TK leads to prevent damage to motor). Maximum torque that can be applied to the terminal block screws is 0.79 Nm (7 lb-in).
Models: FADE 8-4
115/230 Volt Single Phase Fans
Models: FADE 10-4, 12-4, 14-4, 16-4
120/230 Volt Single Phase Fans
Models: FADE 20-6
115 Volt Single Phase Fans
Models: FADE 18-4, 20-4, 22-6, 25-6
115/230 Volt Single Phase Fans
Wiring schematic for 4 lead motors, single phase
Notes:
1. All leads are color
coded as well as
identified with an
Alpha / Alpha or
Alpha / Numeric
code (i.e. TK or Z2).
This code may be
shown as a band on
the wire or on a
schematic on the motor hub. Colors should be verified against code band. If
code band and color do not correspond to schematics above, wire according
to the code on the band.
2. Color of capacitor leads may be reversed. Fan operation will not be affected.
Models: FADE 20-4, 22-6, 25-6
460 Volt Three Phase Fans
Important note: For 460 volt operation, Orange (W2), Red (U2) and
Grey (V2) wires must be spliced together.
Notes:
1. Contactor should
be used. Control
coil should be
wired in series
with motor ther-
mal contacts (TK
leads) as shown
in diagram to pro-
vide thermal
motor protection.
2. All leads are color coded as well as identified with a band containing an
Alpha/Alpha or Alpha/Numeric code (i.e. TK or Z2). Colors should be verified
against code band. If code band and color do not correspond to schematics
above, wire according to the code on the band.
Models: FADE 20-4, 22-6, 25-6
230 Volt Three Phase Fans
Notes:
1. Contactor should
be used. Control
coil should be
wired in series
with motor ther-
mal contacts (TK
leads) as shown
in diagram to pro-
vide thermal
motor protection.
2. All leads are color coded as well as identified with a band containing an
Alpha/Alpha or Alpha/Numeric code (i.e. TK or Z2). Colors should be verified
against code band. If code band and color do not correspond to schematics
above, wire according to the code on the band.
Motor
Leads White (TK)
Black (Z1)
Orange (Z2)
White (TK)
Brown (U1)
Capacitor
(Ground)
L (Black)
N (White)
Supply
Voltage
Blue (U2)
Green/Yellow
Motor
Leads White (TK)
Black (Z1)
Orange (Z2)
White (TK)
Brown (U1)
Capacitor
(Ground)
L (Black)
N (White)
Supply
Voltage
Blue (U2)
Green/Yellow
Motor
Leads White (TK)
Black (Z1)
Orange (Z2)
White (TK)
Brown (U1)
Capacitor
(Ground)
L (Black)
N (White)
Supply
Voltage
Blue (U2)
Green/Yellow
Motor
Leads Black
(Ground)
L (Black)
N (White) Supply
Voltage
Blue
Green/Yellow
L1
Incoming
3-Phase Supply 208/230/460
Control Power
for Contactor
AC Contactor
L2 L3
TK TK L1 L2 L3 L3
Ground
T1 T2 T3
C1
C2
Motor Leads
White or
Brown (TK)

Fantech reserves the right to modify, at any time and without notice, any or all of its products’ features, designs,
components and specifications to maintain their technological leadership position.
Article #: 301076
Item #: 401442
Rev Date: 111210
United States
10048 Industrial Blvd.,
Lenexa, KS 66215
Phone: [phone]
Fax: [phone]
www.fantech.net; [email protected]
Canada
50 Kanalflakt Way,
Bouctouche, NB E4S 3M5
Phone: [phone]
Fax: [phone]
www.fantech.ca; [email protected]
This warranty does not apply to any FANTECH INC. product or part which has failed as a result of faulty installation or abuse, incorrect electrical
connections or alterations made by others, or use under abnormal operating conditions or misapplication of the product or parts. We will not
approve for payment any repair not made by us or our authorized agent without prior written consent. The foregoing shall constitute our sole and
exclusive warranty and our sole exclusive liability, and is in lieu of any other warranties, whether written, oral, implied or statutory. There are no
warranties which extend beyond the description on the page hereof. In no event, whether as a result of breach of contract, or warranty or alleged
negligence, defect incorrect advice or other causes, shall FANTECH be liable for special or consequential damages, including, but not limited to,
loss of profits or revenue, loss of use of equipment or any other associated equipment, cost of capital, cost of substitute equipment, facilities or
services, downtime costs, or claims of customers of purchase for such damages. FANTECH neither assumes or authorizes any person to assume
for it any other liability in connection with the sale of product(s) or part(s). Some jurisdictions do not allow the exclusion or limitation of incidental
or consequential damages so the above limitations and exclusions may not apply to you.
Warning
FANTECH, INC. products are designed and manufactured to provide reliable performance, but they are not guaranteed to be 100% free from
defects. Even reliable products will experience occasional failures and this possibility should be recognized by the user. If these products are used
in a life support ventilation system where failure could result in loss or injury, the user should provide adequate backup ventilation, supplementary
natural ventilation, failure alarm system, or acknowledge willingness to accept the risk of such loss or injury.
Limitation of Warranty and Liability
FANTECH, INC will repair or replace any part which has a factory
defect in workmanship or material. Product may need to be returned
to the FANTECH factory, together with a copy of the bill of sale and
identified with RMA number.
THE FOLLOWING WARRANTIES DO NOT APPLY:
a) To damages from shipping, either concealed or visible;
b) To damages resulting from improper wiring or installation;
c) To damages or failure caused by Acts of God, or resulting from
improper consumer procedures such as
1) improper maintenance,
2) misuse, abuse, abnormal use, or accident and
3) incorrect electrical voltage or current;
d) To removal of, or any alteration to, the Fantech label, control
number or date of manufacture;
e) To any other warranty, expressed, implied or written, and to any
consequential or incidental damages, loss of property, revenues,
or profit or costs of removal, or reinstallation, for any breach of
warranty.
WARRANTY VALIDATION
The end user must keep a copy of the Bill of Sale to verify purchase
date. Valid proof of the date of installation may also serve as a verifica-
tion of commencement of warranty period.
FANTECH RETURN POLICY
Claims for damages or shortages must be reported within ten (10)
days of receipt of product(s). For any product(s) received damaged by
the forwarding agent.
Three (3) Year Warranty
THE FOLLOWING INSTRUCTIONS MUST BE FOLLOWED:
1. For product delivered by UPS:
a) Concealed Damages: Keep all cartons. Call UPS for an inspection
and notify Fantech immediately.
b) Visible Damages: Save all cartons and file complaint directly with
UPS.
2. For product delivered via a common carrier: File damaged goods
claim directly with the freight company.
3. Shortages: Sign only for the total number of pieces received and call
Fantech immediately.
FOR FACTORY RETURN
Product(s) returned without authorization will not be accepted.
Fantech will not accept the return of any special, non-stock, obsolete
or unsaleable product(s). Fantech may, at its option, accept return of
saleable product(s) subject to a 25%
restocking charge.
1. No product(s) will be accepted without a Return Materials
Authorization (RMA) number. This number can be obtained by call-
ing Fantech, Inc. at 800-747-1762. Please have Bill of Sale or
proof of date of installation available.
2. RMA must be clearly marked on outside of carton or delivery will
be refused. All product(s) must be returned freight prepaid.
3. Product(s) will be repaired/replaced and shipped back to buyer; no
credit will be issued.
4. Any out of warranty product will be evaluated and buyer will be noti-
fied of cost; repair cost will be charged to customer; buyer will be
responsible for return freight or product may be returned without
action, to the buyer, freight collect.
No credit will be issued.
This warranty supersedes all prior warranties