FCI ASD-0002 User manual

P a g e | 1
MagicBox Automatic Soap
Dispenser
ASD-0002
Installation Manual
Quality Guarantee
*Thank you for choosing the automatic wall mount soap dispenser. Please
read the instruction carefully before installation. This manual is for your
reference only.

P a g e | 2
Features
•Hands free sensor operation improves
hand washing hygiene.
•Easy installation and low-cost
maintenance
•Battery powered.
•Suitable for schools, offices,
supermarkets, hospitals, and other high
volume facilities

P a g e | 3
Specifications
Power
6V (4 x AA Alkaline batteries)
Sensing Range
5 –15 cm
Soap Vol per
Drop
1 ml
Soap Bottle
Volume
1200 ml
Ambient
Temperature
1 –45 oC
Sensing Range
9 –15 cm
Dispenser Box
Dim
152 x 230 x 117 mm

P a g e | 4
Before Installation
•Locate position of soap dispenser.
•Ensure that soap dispenser does not
interfere with anything above the
lavatory/counter top area. Must be
installed 400 mm above the counter.
•Pay special attention so that the sensor
surface is not flawed or scratched during
the installation process.
•Before installing on the wall, check that no
other piping and wiring is running behind
hole locations. Wall should be sufficiently
reinforced or risk failure due to foam tank
case unit falling.
•Do not place other devices that use an
inverter or infrared sensor near the faucet,
as this may cause the faucet to
malfunction.

P a g e | 5
Tools You will Need
•Power drill with 6 mm wall drill bit
•Flat head screwdriver
•Ruler/tape measure

P a g e | 6
Construction /
Installation Diagram
Box Assembly
i. Using a flat head screw drvier open
the front box cover
ii. Use the mounting grey plastic
bracket as a guide, mark where
holes need to be drilled. Important:
Make sure bracket and case unit is
mounted level.
iii. When installing onto a concrete
wall, drill holes 30 mm deep using a
6 mm masonry drill bit. Insert wall
anchors into the holes and mount
the dispenser using screws.
iv. Remove the grey rubber battery
cover and install 3 AA size
batteries. Assemble back the
rubber cover and tighten the cover
using the four supplied Philips
screws. Guide the male battery box
cable through the bottom opening
and place the case.

P a g e | 7

P a g e | 8
Fill / Refill Soap
1. With the front case cover lowered, remove
the circular grey rubber cap.
2. Fill the soap cartridge with soap. Avoid
overfilling the bottle.
3. Place back the sopa rubber cap, close the
front box cover and securely fasten with
the the flat head box screw.

P a g e | 9
Operations
As the user’s hands enter below the beam’s
effective range (5 –15 cm), the beam is reflected
back into the sensor receiver and activates the
solenoid valve allowing a single soap application
to flow from the dispenser.

P a g e | 10
Soap Volume Adjustment
No adjustments are required for most settings.
Factory default soap volume is 1 ml with switch
setting at 1 ,2. The factory setting should be
satisfactory for most installations.
To adjust the volume:
1. Using a flat head screw driver remove the
screw and lower the front box cover.
2. Using a phillips screw driver remove the two
phillips screw & the washers that are securing
the soap cartridge. Ensure the both the rubber
sopa & battery caps are tightly secured onto
the soap cartridge
3. Turn the cartridge upside down.
4. Adjust soap volume using the red dip switch
dials for:
i. Two drops set switch to O, 2
ii. Four drops set switch to 1, N
iii. 8 drops drops set switch to O,N

P a g e | 11
Soap Dispensing
Range Adjustments
No adjustments are required for most settings.
Factory default range is set at 12 cm. The factory
setting should be satisfactory for most
installations.
To adjust the dispensing range:
1. Using a flat head screw driver remove the
screw and lower the front box cover.
2. Using a phillips screw driver remove the
two phillips screw & the washers that are
securing the soap cartridge. Ensure the
both the rubber sopa & battery caps are
tightly secured onto the soap cartridge.
3. Turn the cartridge upside down.
4. With a small flat screw driver turn the
potentiometer (small brass dial) clockwise
to increase sensing range &
counterclockwise to reduce range.

P a g e | 12
Box Diagram

P a g e | 13
Battery Replacement
1. Using a flat head screw driver remove the
screw and lower the front box cover.
2. Remove the rubber grey cover / cap
3. Remove the three AA size batteries.
4. Replace with 3 new batteries, place back
the cover.
5. Enclose the box cover and tighten the
flathead screw.
Troubleshooting
1. Unit does not operate
i. Check battery. Remove & replace
3 AA size batteries.
2. Soap does not dispense
i. Soap bottle needs refill. Refill
soap.
ii. Check soap dispensing nozzle for
clog. Clean nozzle with soft cloth.

P a g e | 14
Care & Cleaning
DO NOT USE abrasive or chemical cleaners
(including chlorine bleach) to clean dispenser
that may dull the luster and attack the special
decorative finishes. Use ONLY mild soap and
water, then wipe dry with clean cloth or towel.
While cleaning the bathroom tile, protect the
dispenser from any splattering of cleaner. Acids
and cleaning fluids will discolor or remove
decorative finish.

P a g e | 15
Resources
Warranty Information
For Installation guides, visit our
resource page through the QR
code.
Alternatively, you can visit our
resource page at
https://faucetscanada.ca/resources/
To view more products from
Faucets Canada, visit our shop
page through the QR code.
Alternatively, you can visit our shop
page at
https://faucetscanada.ca/shop/
For information on product warranty,
visit our resource page through the
QR code.
Alternatively, you can visit our warranty
claims page at
https://faucetscanada.ca//warranty-claim/

P a g e | 16
About us
Here at FCi, our main goal is to break the eco-
innovation boundary and provide customers with
fixtures that save water and deliver reliable
sources of sanitation every time.
As Canada’s favourite automatic faucet brand,
we are proud to say we deliver quality touchless
fixtures that perform beyond expectations and
exceed design standards.
To learn more about Faucets Canada, please visit our website at
FacucetsCanada.ca