Federal Signal Corporation AM300X Quick guide

MODELO AM300X
INSTRUCCIONES PARA LA INSTALACIÓN Y EL
MANTENIMIENTO
DE LOS MODELO AM300X
MODEL AM300X
INSTALLATION AND SERVICE INSTRUCTIONS
FOR MODEL AM300X
MODÈLE AM300X
CONSIGNES POUR L’INSTALLATION ET L’UTILISATION
DES MODÈLE AM300X
2562142A
Rev. A1 314
Printed in U.S.A.

blank page

-1-
INSTALLATION INSTRUCTIONS
FOR
MODEL AM300X AUDIOMASTER EXPLOSION-PROOF SPEAKER
Failure to follow all safety precautions and instructions may result in prop-
erty damage, serious injury, or death to you or others.
SAFETY MESSAGE TO INSTALLERS
People’s lives depend on your safe installation of our products. It is important to
follow all instructions shipped with the products. This device is to be installed by a
trained electrician who is thoroughly familiar with the National Electric Code and will
follow the NEC guidelines as well as local codes.
The selection of the mounting location for the device, its controls and routing of
the wiring is to be accomplished under the direction of the Facilities Engineer and the
Safety Engineer. In addition, listed below are some other important safety instructions
and precautions you should follow:
• Readandunderstandallinstructionsbeforeinstallingoroperatingthis
equipment.
• Thisunitmustbeinstalledbyaqualiedelectricianinaccordancewith
all National and local Electrical and Fire Codes, under the direction of
the authority having jurisdiction.
• Donotconnectthisunittothesystemwhenpowerison.
• Alleffectivewarningspeakersproduceloudsoundswhichmaycause,in
certainsituations,permanenthearingloss.Youshouldtakeappropriate
precautions such as wearing hearing protection.
• Afterinstallation,testthesoundsystemtoensureproperoperation.
• Alleffectivewarningspeakersproduceloudsounds,whichmaycause,
in certain situations, permanent hearing loss. The device should be
installed far enough away from potential listeners to limit their exposure
whilestillmaintainingitseffectiveness.TheOSHACodeofFederal
Regulations1910.95NoiseStandardprovidesguidelineswhichmaybe
used regarding permissible noise exposure levels.
• ShowtheseinstructionstoyourSafetyEngineerandthenlethemin
a safe place and refer to them when maintaining and/or reinstalling the
unit.
• Afterinstallationandcompletionofinitialsystemtest,aprogramof
periodictestingofthisdevicemustbeestablished.RefertoNFPA72G,
local Fire Codes and the authority having jurisdiction for this informa-
tion.
• Consulttheauthorityhavingjurisdictioninyourarearegardingthe
proper use and installation of this product.

-2-
I. GENERAL.
 TheAudioMasterModelAM300Xisa25Vrmsand70Vrms,indoor/outdoorrated,
selectablepoweroutput(1,2,7,or15watts),hazardouslocationloudspeakerforuse
withrealarmandgeneralsignalingsystemssuchasFederalSignal’sSelecTone
system. This model is suitable for use in areas with high ambient noise levels. It is
designed to reproduce electronically generated warning tones, which command rapid
recognition,andfullrangevoicecommunication.Anadjustablemountingbracketis
provided to allow positioning for desired sound coverage.
II. SPECIFICATIONS.
OperatingVoltage: 25Vrmsor70Vrms
PowerInput(selectable): 1W,2W,7W,and15W
MaximumSupervisoryVoltage: 50VDC
Weight(approx.):  15.7lbs.(7.1kg)
Size:   16.3”(414mm)long,17.0”(432mm)high,13.1”(333mm)wide
Construction: Aluminumenclosureandadjustablesteelmountingbracketwitha
powdercoatnish
FrequencyResponse
 Voice:   800-3150Hz
 Tone:   400-4000Hz
ApprovalAgencyListings: Referenceproductnameplate
AudibilityinformationisshowninTable1.
III. INSTALLATION.
 A. Unpacking.
  Afterunpackingthespeaker,examineitcarefullyforpossibledamagethat
mayhaveoccurredintransit.Ifequipmenthasbeendamaged,immediatelyleaclaim
withthecarrierstatingtheextentofthedamage.Carefullycheckallshippinglabels
and tags for special instructions before removing or destroying them.
B. Mounting Arrangements.
  Thespeakercanbemountedonanyrelativelyatsurfacecapableofsupport-
ingthespeaker’sweight.Conduitconnectionscanbemadetothe1/2”NPTthreaded
openingsatbottomofthehousing(seegure2).
Property damage, serious injury, or death could occur if an accumulation of
water,snow,dust,etc.residesinthespeakerprojector,severelyreducingor
preventingoperationofthisdevice.Mounttheunitsospeakerprojectoris
pointedhorizontallyorslightlydownward.
  1. Removethetwo1/2”-13hexheadbolts,atwashersandlockwashers
thatsecurethemountingbrackettotheunit.Disconnectthelanyardfromthemount-
ingbracketatthecotterring.
  2. Selectamountinglocation.

-3-
Property damage, serious injury, or death could occur if any objects are in
frontofspeaker,severelyreducingoptimumsounddistribution.Formaxi-
mumeffectiveness,ensurethatthefrontofthespeakerisclearofobstruc-
tions.
  3. Usingthemountingbracketasatemplate,scribedrillpositionmarkson
themountingsurface.Seegure1formountingholelocationsanddimensions.
Before drilling holes in any surface, be sure both sides of surface are clear of
anything that could be damaged.
  4. Drillholesatthepreviouslyscribeddrillpositionmarkstoaccommodate
1/2”diameterscrews.
  5.Securebrackettomountingsurfacewith1/2”diameterscrewsappropriate
for the type of mounting surface material.
Property damage, serious injury, or death could occur if the machined sealing
surfaces are damaged on this product. To maintain the effectiveness of the
explosion-proof enclosure, be careful to avoid damaging the machined sealing
surfaces of cover and housing.
  6. Reattachunittoitsmountingbracketwiththetwo1/2”-13hexhead
bolts,atwashersandlockwasherspreviouslyremoved.Positionspeakersoastoob-
tain desired sound
coverage then tighten these bolts securely.
  7. Reattachthelanyardtothecotterringandmountingbracket.Checkto
verifythatitissecurelyattachedtoboththecoverandthemountingbracket.Loosen
andremovethethreadedcoverbyturningitcounter-clockwise.Allowthecovertohang
by the attached
lanyard.
  8. Routewiresthroughthe1/2”NPTthreadedopeningsintothehousingin
accordancewithnationalandlocalelectricalandrecodes.Wiresizedependsupon
the operating current and the distance from the power source.
  9. Beforereinstallingthehousingcover,readparagraphC,insectionIII,
ELECTRICALCONNECTIONSbelowandmakenecessaryconnections.

-4-
C. Electrical Connections.
Toavoidelectricalshock,donotconnectwireswhencircuitsareenergized.
NOTE
Audiowiresshouldbesizedproperlybyyourlicensedinstallationelectrician
for your service application. This cable requires a twisted shielded pair with
an18AWGminimumandshouldproducenomorethan15%signallineloss
over the length of the cable run.
National Electrical Code, as well as local codes, must be followed during installa-
tionofthesemodels.Allelectricalwiringmustberoutedthroughconduitandttings
approved for explosion-proof installations.
  1. Connecttheaudiocommonleads(-)tothespeaker’scommonterminal
(markedCOM)andtheaudiopositive(+)leadstothedesiredwattageterminal(see
gures2and3).
Anun-insulatedsectionofasingleconductormustNOTbeloopedarounda
terminalandusedastwoseparateconnections.NFPA72requiresthatthe
wire is severed to provide electrical supervision of the connection.
  2. Usingthesuppliedjumperwire,connectoneendofthejumperwireto
theterminalmarkedwiththeappropriateoperatingvoltage(seegure3).Connectthe
otherendtotheterminalmarked“SPK”.
  3. Carefullyreinstallhousingcoverandtightenituntilthecoverange
makescontactwiththehousing.Tightenthesetscrewonthecovertosecurethecover.
Verifythatthemountingboltshavebeensecurelytightened.
Property damage, serious injury, or death could occur if the housing is not
closedproperly.Toreducepossibilityofexplosion,housingcovermustbekept
tightwhilecircuitsareenergized.
IV. TESTING / OPERATING.
Undercertainconditionsthesedevicesarecapableofproducingsoundsloud
enoughtocausehearingdamage.Adequatehearingprotectionshouldbe
wornifstandingwithincloseproximitytodevicewhiletesting.Recommen-
dationsintheOSHASoundLevelStandard(29CFR1910)shouldnotbe
exceeded.

-5-
 A. Afterinstallationiscomplete,besuretotestthesystemtoverifythateach
speakeroperatessatisfactorily.Ifitisfoundthattheunitistooloudforitslocation,a
lower wattage tap may be selected. Carefully remove the housing cover and move the
positive(+)leadtoalowerwattagetap(seegure3).Reinstallthehousingcoverand
retest.
Property damage, serious injury, or death could occur if the housing is not
closedproperly.Toreducepossibilityofexplosion,housingcovermustbekept
tightwhilecircuitsareenergized.
 B. Aftercompletionofinitialsystemtest,establishaprogramforperiodic
testingofthisdevice.RefertoNFPA72G,localFireCodesandtheauthorityhaving
jurisdiction for this information.
C. Provide a copy of these instructions for the Safety Engineer, system
operator(s)andmaintenancepersonnel.
SAFETY MESSAGE TO OPERATORS
Even if your warning system is operating properly, it may not be completely
effective. People may not hear or heed your warning signal. You must recog-
nizethisfactandensurethatyourwarningsignalachievesitsintendedeffect
throughpropertest/trainingsequenceswithinyourspecicapplication(s).
V. MAINTENANCE.
SAFETY MESSAGE TO MAINTENANCE PERSONNEL
Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death to you or others.
• Readandunderstandallinstructionsbeforeperformingmaintenanceon
this unit.
• Donotperformmaintenanceonthisunitwhencircuitsareenergized.
• Periodicchecksshouldbemadetoensurethateffectivenessofthis
devicehasnotbeenreducedbecausespeakerhasbecomecloggedwith
a foreign substance or because objects have been placed in front of the
speaker.
• AnymaintenancetothisunitMUSTbeperformedbyatrainedelectri-
cian in accordance with NEC guidelines and local codes.
• Neveralterthisunitinanymanner.Safetyinhazardouslocationsmay
bejeopardizedifadditionalopeningsoralterationsaremadetothis
device.
• Thenameplates,whichcontaincautionaryorotherinformationofim-
portance to maintenance personnel, should not be obscured if exterior of
device is painted.

-6-
Effectivenessofexplosion-proofenclosuremustbemaintained.Usecautionto
avoid damaging machined surfaces.
EXPLOSION HAZARD
SubstitutionofanycomponentsmayimpairsuitabilityforClassI,Division2,
andClassI,Zone2.
ThisequipmentissuitableforuseinClassI,Division1,GroupsB,C,andD;
ClassI,Division2,GroupsA,B,C,andD;ClassII,Division2,GroupsFand
G;ClassIIIornon-hazardouslocationsonly.
 A. Periodicallycheckthisdevicetoverifythattherearenoforeignsubstances
in,orinfrontof,thespeaker,whichwillreduceitseffectiveness.
 B. Testingshouldbeperiodicallyperformed.RefertoNFPA720,localFireCodes
and the authority having jurisdiction for information.
C. In the event a volume adjustment or other repair is required, be sure to refer
totheSafetyMessageForMaintenancePersonnelbeforeproceeding.
VI. SERVICE.
Unauthorizedrepair/servicingoftheunitmayresultindegradationofperfor-
mance and/or property damage, serious injury, or death to you or others. If a
malfunctioningunitisencountered,donotattemptanyeldrepair/retrotof
parts.
Federal Signal will service your equipment or provide technical assistance with
any problems that cannot be handled locally.
 AnyunitsreturnedtoFederalSignalforservice,inspection,orrepairmustbe
accompaniedbyaReturnMaterialAuthorization.ThisR.M.A.canbeobtainedfromthe
localDistributororManufacturer’sRepresentative.
 Atthistimeabriefexplanationoftheservicerequestedorthenatureofthemal-
function
should be given.
 Addressallcommunicationsandshipmentsto:
Industrial Systems
2645FederalSignalDrive•UniversityPark,IL60484-3167
Tel:708-534-4756•877-289-3246•Fax:708-534-4852
Email: [email protected] •www.federalsignal-indust.com •www.fs-isys.com

INSTRUCCIONES PARA LA INSTALACIÓN
DEL
ALTAVOZ A PRUEBA DE EXPLOSIONES MODELO AM300X AUDIOMASTER
Si no se siguen todas las precauciones e instrucciones de seguridad pueden ocurrir
daños a la propiedad y causar lesiones graves o mortales a usted o a otras perso-
nas.
MENSAJE DE SEGURIDAD PARA LOS INSTALADORES
 Lavidadepersonasdependedelainstalaciónseguradenuestrosproductos.Esimpor-
tante seguir todas las instrucciones que vienen con estos productos. Este dispositivo debe ser
instaladoporunelectricistacapacitadoqueconozcaperfectamenteelCódigoEléctricoNacio-
nalysigatodaslasDirectricesdelCódigoNECasícomoloscódigoslocales.
 Laseleccióndellugardemontajeparaeldispositivo,suscontrolesyladistribucióndel
cableadodeberealizarsebajoladireccióndelingenierodeplantayelingenierodeseguridad.
Además,acontinuaciónindicamosalgunasotrasinstruccionesimportantesyprecaucionesde
seguridad que debe seguir:
• Leaycomprendatodaslasinstruccionesantesdeinstalaroponerafuncionar
este equipo.
• Estaunidaddebeserinstaladaporunelectricistapreparadoenconformidad
conlosCódigosNacionalesylocalesEléctricosydeIncendioybajoladirec-
cióndelaautoridadalaquecorrespondalajurisdicción.
• Noconecteestaunidadalsistemamientrasestérecibiendoenergíaeléctrica.
• Todoslosaltavocesecacesdealarmaproducensonidosfuertes,queencier-
tassituacionespuedencausarlapérdidapermanentedelaaudición.Tomelas
precaucionesapropiadastalescomousarprotecciónparalosoídos.
• Despuésdelainstalación,pruebeelsistemadesonidoparaasegurarsede
que funcione correctamente.
• Todoslosaltavocesecacesdealarmaproducensonidosfuertesqueenciertas
situacionespuedencausarlapérdidapermanentedelaaudición.Estedispo-
sitivodebeinstalarseaunadistanciaqueevitelaexposicióndelaspersonas
alsonidofuertesinquesepierdasuecacia.ElCódigodeReglamentosFede-
ralesdelaOSHAensuNormasobreruidos1910.95estipulalasdirectrices
quepuedenaplicarserespectoalosnivelesadmisiblesdeexposiciónalruido.
• Muestreestasinstruccionesasuingenierodeseguridadyluegoarchívelasen
unlugarseguroyconsúltelascuandoestéhaciendomantenimientooreinsta-
lando la unidad.
• Despuésdelainstalaciónylapruebainicialdelsistema,sedebeestablecer
unprogramadepruebasperiódicasparaestedispositivo.ConsultelosCódi-
goslocalesdeincendioNFPA72Gyalasautoridadescompetentessobreesta
información.
• Consultealasautoridadescompetentesensuáreasobreelusoylainstala-
cióncorrectadeesteproducto.
-7-

-8-
I. GENERAL.
 ElmodeloAudioMasterAM300Xesunaltavozde25Vrmsy70Vrmsconsalidade
energíaseleccionable(1,2,7ó15vatios),clasicadoparausobajotechoyalairelibreenlu-
garesdealtoriesgoconalarmasdeincendioysistemasdeseñalizacióngeneraltalescomoel
sistemaSelecTonedeFederalSignal.Estemodeloesapropiadoparaserusadoenáreascon
nivelesderuidoambientalaltos.Estádiseñadoparareproducirtonosdealertagenerados
electrónicamente,conreconocimientorápidodecomandosygamacompletadecomunicación
devoz.Seproporcionaunsoportedemontajeparapermitirsuposicionamientoyobtenerla
cobertura de sonido deseada.
II. ESPECIFICACIONES.
Voltajedeoperación: 25Vrmso70Vrms
Entradadeenergía(seleccionable): 1vatio,2vatios,7vatiosy15vatios
Voltajedesupervisiónmáximo: 50Vdc
Peso(aprox.):   7,1kg(15,7lb)
Tamaño:    414mm(16,3pulg)delargo,432mm(17,0pulg)
     dealto,333mm(13,1pulg)deancho
Construcción:   Cajadealuminioysoportedemontajeajustable
     deaceroconunacabadodepoliéster
Respuestadefrecuencia
 Voz:    800-3.150Hz
 Tono:   400-4.000Hz
ListadeAgenciasAprobatorias: Consultelaplacadeidenticacióndelproducto
LainformacióndeaudibilidadsemuestraenlaTabla1.
III. INSTALACIÓN.
 A. Desembalaje
  Despuésdedesembalarelaltavoz,revíselocuidadosamenteparadetectarcual-
quierdañoquepuedahaberocurridodurantesutransporte.Sielequipoestádañado,presen-
teinmediatamenteunareclamaciónanteeltransportistaindicandolaextensióndelosdaños.
Revisecuidadosamentetodaslasetiquetasdeenvíoyrótulosparaversihayalgunainstruc-
ciónespecialantesderetirarlosodestruirlos.
B. Distribución del montaje.
  Estosaltavocessepuedenmontarencualquiersupercierelativamenteplanaque
puedasoportarelpesodelaltavoz.Lasconexionesdelconductosepuedenhacerenlosaguje-
rosroscadosNPTde1/2pulgenelfondodelacaja(vealagura2).
Pueden ocurrir daños a la propiedad o lesiones graves o mortales si se acumula
agua,nieve,polvo,etc.enelproyectordelaltavoz,reduciendosignicativamenteo
impidiendolaoperacióndeestedispositivo.Montelaunidaddetalmaneraqueel
proyectordelaltavozseorientehorizontalmenteounpocohaciaabajo.
  1. Quitelosdostornillosdecabezahexagonalde1/2pulg-13,lasarandelas
planasylasarandelasdepresiónqueaseguranelsoportedemontajealaunidad.Quiteel
cordóndelanillodepasadorenelsoportedemontaje.
  2. Seleccioneellugardemontaje.