Federal Signal Corporation Modulator MOD Series User manual

Description, Specications,
Installation, and Service Manual
25500059
Rev. A2 0519
Printed in U.S.A.
© Copyright 2013-2019 Federal Signal Corporation
Modulator®High-Powered
Omni Speaker
Model: MOD Series
Shown with optional QuadraFlare lights

Limited Warranty
This product is subject to and covered by a limited warranty,
a copy of which can be found at www.fedsig.com/SSG-Warranty.
A copy of this limited warranty can also be obtained by written
request to Federal Signal Corporation, 2645 Federal Signal Drive,
University Park, IL 60484, email to [email protected] or
call [phone].
This limited warranty is in lieu of all other warranties, express or
implied, contractual or statutory, including, but not limited to the
warranty of merchantability, warranty of tness for a particular
purpose and any warranty against failure of its essential purpose.
2645 Federal Signal Drive
University Park, Illinois 60484
www.fedsig.com
Customer Support 800-548-7229 • [phone]
Technical Support 800-524-3021 • [phone]
All other product names or trademarks are properties of their respective owners.
All products indicated are trademarks of Federal Signal Corporation.

3
Description, Specications, Installation, and Service Manual
Contents
Safety Messages......................................................................................................................................................5
General Description ................................................................................................................................................7
Introduction .........................................................................................................................................................7
Features..............................................................................................................................................................7
Ordering Information ...........................................................................................................................................9
Specications ..........................................................................................................................................................9
Installation..............................................................................................................................................................12
Determining a Suitable Location .......................................................................................................................12
Installing the Sirens...........................................................................................................................................13
Connecting the Driver Wires.....................................................................................................................13
Wooden Pole Mounting.....................................................................................................................................14
Steel Pole Mounting..........................................................................................................................................16
Flat Surface Mounting.......................................................................................................................................18
Driver Connections ...........................................................................................................................................18
Installing Lights on the Siren.............................................................................................................................21
Installing the Top Light Kit .........................................................................................................................21
Installing the Side Light Kit........................................................................................................................22
Pre-Operation Checkout ...................................................................................................................................23
Maintenance...........................................................................................................................................................23
Replacing the Driver .........................................................................................................................................24
Ordering Parts...................................................................................................................................................24
Getting Service ......................................................................................................................................................24
Figures
Figure 1 Modulator Speaker ...................................................................................................................................8
Figure 2 Siren Leg Assembly ...............................................................................................................................14
Figure 3 Typical Wooden Pole-mounted Installation .........................................................................................15
Figure 4 Steel Pole Mounting ...............................................................................................................................17
Figure 5 Siren Base Plate .....................................................................................................................................18
Figure 6 Driver Connections ................................................................................................................................19

4
Modulator High-Powered Omni Speaker (MOD Series)
Tables
Table 1 MOD Models Sound Output.......................................................................................................................7
Table 2 Ordering Information .................................................................................................................................9
Table 3 General Specications...............................................................................................................................9
Table 4 MOD1004B ................................................................................................................................................10
Table 5 MOD2008B ................................................................................................................................................10
Table 6 MOD3012B ................................................................................................................................................10
Table 7 MOD4016B ................................................................................................................................................10
Table 8 MOD5020B ................................................................................................................................................ 11
Table 9 MOD6024B ................................................................................................................................................ 11
Table 10 MOD6032B .............................................................................................................................................. 11
Table 11 MOD8032B............................................................................................................................................... 11
Table 12 Sound levels predictions.......................................................................................................................12
Table 13 Number of Wires and Cable Length per Module .................................................................................19
Table 14 Top Light Kit (Model 191XL-024R) ........................................................................................................21
Table 15 Side Light Kit (Model MOD-QF-KIT)......................................................................................................22
Table 16 Replacement Parts .................................................................................................................................24
Figure 7 MOD6032B Driver Connections ............................................................................................................20
Figure 8 Top Light .................................................................................................................................................21
Figure 9 Side Light ................................................................................................................................................22
Figure 10 Side Light Wiring..................................................................................................................................22

5
Safety Messages
Description, Specications, Installation, and Service Manual
Safety Messages
It is important to follow all instructions shipped with this product. This device is to be
installed by trained personnel who are thoroughly familiar with the country electric codes
and will follow these guidelines as well as local codes and ordinances, including any
state or local noise control ordinances. Listed below are important safety instructions and
precautions you should follow:
Important Notice
Federal Signal reserves the right to make changes to devices and specications detailed in
the manual at any time in order to improve reliability, function or design. The information
in this manual has been carefully checked and is believed to be accurate; however, no
responsibility is assumed for any inaccuracies.
Publications
Federal Signal recommends the following publications from the Federal Emergency
Management Agency for assistance with planning an outdoor warning system:
• The “Outdoor Warning Guide” (CPG 1-17)
• “Civil Preparedness, Principles of Warning” (CPG 1-14)
• FEMA-REP-1, Appendix 3 (Nuclear Plant Guideline)
• FEMA-REP-10 (Nuclear Plant Guideline).
Planning
• If suitable warning equipment is not selected, the installation site for the siren is
not selected properly or the siren is not installed properly, it may not produce the
intended optimum audible warning. Follow Federal Emergency Management Agency
(FEMA) recommendations.
• If sirens are not activated in a timely manner when an emergency condition
exists, they cannot provide the intended audible warning. It is imperative that
knowledgeable people, who are provided with the necessary information, are
available at all times to authorize the activation of the sirens.
• When sirens are used out of doors, people indoors may not be able to hear the
warning signals. Separate warning devices or procedures may be needed to
effectively warn people indoors.
• The sound output of sirens is capable of causing permanent hearing damage. To
prevent excessive exposure, carefully plan siren placement, post warnings, and
restrict access to areas near sirens. Review and comply with any local or state noise
control ordinances as well as OSHA noise exposure regulations and guidelines.
• Activating the sirens may not result in people taking the desired actions if those to
be warned are not properly trained about the meaning of siren sounds. Siren users
should follow FEMA recommendations and instruct those to be warned of correct
actions to be taken.

6
Safety Messages
Modulator High-Powered Omni Speaker (MOD Series)
• After installation, service, or maintenance, test the siren system to conrm that it is
operating properly. Test the system regularly to conrm that it will be operational in
an emergency.
• If future service and operating personnel do not have these instructions to refer to,
the siren system may not provide the intended audible warning and service personnel
may be exposed to death, permanent hearing loss, or other bodily injury. File these
instructions in a safe place and refer to them periodically. Give a copy of these
instructions to new recruits and trainees. Also give a copy to anyone who is going to
service or repair the siren.
Installation and Service
• Electrocution or severe personal injury can occur when performing various
installation and service functions such as making electrical connections, drilling
holes, or lifting equipment. Therefore only experienced electricians should install
this product in accordance with national, state and any other electrical codes having
jurisdiction. Perform all work under the direction of the installation or service crew
safety foreman.
• The sound output of sirens is capable of causing permanent hearing damage. To
prevent excessive exposure, carefully plan siren placement, post warnings and
restrict access to areas near the sirens. Sirens may be operated from remote control
points. Whenever possible, disconnect all siren power including batteries before
working near the siren.
• After installation or service, test the siren system to conrm that it is operating
properly. Test the system regularly to conrm that it will be operational in an
emergency.
• If future service personnel do not have these warnings and all other instructions
shipped with the equipment to refer to, the siren system may not provide the intended
audible warning and service personnel may be exposed to death, permanent hearing
loss, or other bodily injury. File these instructions in a safe place and refer to them
periodically. Give a copy of these instructions to new recruits and trainees. Also, give
a copy to anyone who is going to service or repair the sirens.
Operation
Failure to understand the capabilities and limitations of your siren system could result in
permanent hearing loss, other serious injuries or death to persons too close to the sirens
when you activate them or to those you need to warn. Carefully read and thoroughly
understand all safety notices in this manual and all operations-related-items in all
instruction manuals shipped with equipment. Thoroughly discuss all contingency plans
with those responsible for warning people in your community, company, or jurisdiction.
Read and understand the information contained in this manual before
attempting to install or service the siren.
Pay careful attention to the notice located on the equipment.

7
General Description
Description, Specications, Installation, and Service Manual
General Description
Introduction
Federal Signal Modulator Series siren products are a family of electronic sirens that are
capable of producing high-intensity warning signals over a large area. The siren consists
of a speaker array and Control/Battery Cabinets. A highly efcient design enables the
siren to produce a high-sound level while making moderate demands on the power
source.
Modulator models purchased after September 2017 are precongured to support top and
side lights kits for visual signaling options that can enhance the proven technology of the
Modulator’s intelligible voice communication and signaling.
Federal Signal omni-directional, electronic Modulator Series siren consists of aluminum
modules that use four 100-watt drivers per module. The Modulator series B is available in
several models, which have the following sound output rating at 100 feet.1See Table 1.
The MOD6032B is a 3200-watt siren that uses the MOD6024B siren conguration. The
middle two modules use eight 100-watt drivers.
Table 1 MOD Models Sound Output
Model Decibels at 100 feet
MOD1004B2106 dBC
MOD2008B2112 dBC
MOD3012B2115 dBC
MOD4016B2118 dBC
MOD5020B2120 dBC
MOD6024B2121 dBC
MOD6032B2123 dBC
MOD8032B2124 dBC
1Based on measurements at 500 feet.
2Add the letter C to the Modulator model name for Steel/Concrete pole mount model.
The Modulator Series siren provides virtually at frequency response from
200-2000 Hertz. This gives the siren the ability to produce loud and clear voice messages
and produce a full spectrum of warning tones.
An UltraVoice Controller (Model UV) is needed for complete operation.
Features
The Modulator Speaker has the following features:
• Light-weight, compact design
• Uses Federal Signal Ultravoice® for control and amplication
• Excellent frequency response for clear voice reproduction

8
General Description
Modulator High-Powered Omni Speaker (MOD Series)
• 360º coverage without sound variation in horizontal planes
• Easy servicing through convenient access panels
• Anechoic chamber-certied
• Optional visual signaling options that enhance the Modulator’s intelligible voice
communication and signaling
• New models offer steel/concrete pole mounting solution
The following is a picture of the Modulator.
Figure 1 Modulator Speaker
MOD1004B
26.37"
MOD2008B
39.91"
MOD3012B
53.51"
MOD4016B
67.11"
MOD5020B
80.71"
MOD6024B/MOD6032B
94.37"
MOD8032B
122.44"
35.00"
13.60

9
Specications
Description, Specications, Installation, and Service Manual
Ordering Information
Contact our Federal Signal sales engineers to design a system that meets your specic
requirements. Specify speaker array model number. Each speaker array model must be
ordered with a specic corresponding UV and amplier.
Table 2 Ordering Information
Speaker Controller1
MOD1004B2UV + 1 UV400
MOD2008B2UV + 2 UV400
MOD3012B2UV + 3 UV400
MOD4016B2UV + 4 UV400
MOD5020B2UV + 5 UV400
MOD6024B2UV + 6 UV400
MOD6032B2UV + 8 UV400
MOD8032B2UV + 8 UV400
1Controllers available in radio, IP, and landline.
2Add the letter C to the Modulator model name for Steel/Concrete pole mount model.
NOTE: For the standard cable length supplied with the siren see “Table 13 Number
of Wires and Cable Length per Module” on page 19. Extension cable is also
available in 10-foot increments. Mounting the UV controller farther than 100 feet is not
recommended. (Farther mounting may decrease power output.)
Specications
Table 3 General Specications
Color Weather Guard White III
Paint Type TGIC Polyester Powder Coat
Modular Horn Type Hyperbolic Flare
Frequency Response 200-2000 Hz
Horizontal Coverage 360 Degrees
Bottom (non-active) Module* Dimensions 13-1/2 x 35 inches Diameter
Input Voltage 66 VRMS min., 400 W max.
* The bottom module of the siren is a passive device that does not contain any drivers. Its
functional use is to complete the horn formed by the bottom and the rst active module.
The bottom module also provides a mounting solution for the optional side lights.
The following tables list each MOD model number with its specications. Each speaker
array model must be ordered with a specic corresponding UV and Amplier.
Wind load calculations are for speaker array only.

10
Specications
Modulator High-Powered Omni Speaker (MOD Series)
Table 4 MOD1004B
Number of Active Modules 1
Power 400 watts
dB Output 106 dBC at 100 feet (30.48 m)
Height of Speaker Array 26.37 inches (66.98 cm)
Weight 125 lb (56.70 kg)
EPA at 40 feet (12.19 m) 3.30 ft2 (0.31 m2)
Wind Load (110 mph, 40 feet above ground) 252 lb (114.31 kg)
Table 5 MOD2008B
Number of Active Modules 2
Power 800 watts
dB Output 112 dBC at 100 feet (30.48 m)
Height of Speaker Array 38.91 inches (98.83 cm)
Weight 190 lb (86.18 kg)
EPA at 40 feet (12.19 m) 4.94 ft2 (0.46 m2)
Wind Load (110 mph, 40 feet above ground) 378 lb (171.46 kg)
Table 6 MOD3012B
Number of Active Modules 3
Power 1200 watts
dB Output 115 dBC at 100 feet (30.48 m)
Height of Speaker Array 53.51 inches (135.92 cm)
Weight 255 lb (115.67 kg)
EPA at 40 feet (12.19 m) 6.59 ft2 (0.61 m2)
Wind Load (110 mph, 40 feet above ground) 504 lb (228.61 kg)
Table 7 MOD4016B
Number of Active Modules 4
Power 1600 watts
dB Output 118 dBC at 100 feet (30.48 m)
Height of Speaker Array 67.11 inches (170.46 cm)
Weight 320 lb (145.15 kg)
EPA at 40 feet (12.19 m) 8.24 ft2 (0.77 m2)
Wind Load (110 mph, 40 feet above ground) 630 lb (285.76 kg)

11
Specications
Description, Specications, Installation, and Service Manual
Table 8 MOD5020B
Number of Active Modules 5
Power 2000 watts
dB Output 120 dBC at 100 feet (30.48 m)
Height of Speaker Array 80.71 inches (205.00 cm)
Weight 385 lb (174.63 kg)
EPA at 40 feet (12.19 m) 9.89 ft2 (0.92 m2)
Wind Load (110 mph, 40 feet above ground) 756 lb (342.92 kg)
Table 9 MOD6024B
Number of Active Modules 6
Power 2400 watts
dB Output 121 dBC at 100 feet (30.48 m)
Height of Speaker Array 94.37 inches (239.70 cm)
Weight 450 lb (204.12 kg)
EPA at 40 feet (12.19 m) 11.54 ft2 (1.07 m2)
Wind Load (110 mph, 40 feet above ground) 882 lb (400.07 kg)
Table 10 MOD6032B
Number of Active Modules 6
Power 3200 watts
dB Output 123 dBC at 100 feet (30.48 m)
Height of Speaker Array 94.37 inches (239.70 cm)
Weight 496 lb (224.98 kg)
EPA at 40 feet (12.19 m) 11.54 ft2 (1.07 m2)
Wind Load (110 mph, 40 feet above ground) 882 lb (400.07 kg)
Table 11 MOD8032B
Number of Active Modules 8
Power 3200 watts
dB Output 124 dBC at 100 feet (30.48 m)
Height of Speaker Array 122.44 inches (311 cm)
Weight 580 lb (263.08 kg)
EPA at 40 feet (12.19 m) 14.85 ft2 (1.38 m2)
Wind Load (110 mph, 40 feet above ground) 1134 lb (514.37 kg)

12
Installation
Modulator High-Powered Omni Speaker (MOD Series)
Installation
Read and adhere to all safety warnings in this manual before installing the
Modulator Series Speaker.
Determining a Suitable Location
The output level of the sirens is capable of causing permanent hearing
damage. To prevent excessive exposure, carefully plan the siren location and
post warnings where excessive levels may be encountered. Refer to OSHA 29
CFR 1910.95 for safe exposure limits.
Do not expose personnel to sound levels above 123 dBC.
Careful consideration of the factors affecting the propagation of sound from the siren
and the response of the human ear to the sound will optimize the ability of the siren
to effectively warn the community. Follow Federal Emergency Management Agency
(FEMA) guidelines when designing the warning system.
The reduction of signal intensity, as the distance from the siren increases and the
minimum desired signal level at the fringe of the area to be covered, are important
considerations when choosing a siren installation site. As the distance from the siren
increases, sound level losses accumulate. These losses are a result of weather conditions,
the terrain, obstructions in the sound path, the pitch of the sound and the height of the
siren.
Optimum sound propagation conditions occur when no obstructions exist in the sound
path, the terrain is hard and at, and the air is blowing away from the source. Under these
conditions, you can expect a 6 dB loss per distance doubled. A loss per distance doubled
of 10 dB is typically experienced because atmosphere is rarely calm, terrain may not be
at, and buildings or other obstructions are frequently present in the sound path.
Using a 10 dB per distance doubled loss factor, the following sound levels are predicted
for the sirens in the following table.
Table 12 Sound levels predictions
Distance MOD6024B
100 feet (30.5 m) the sound level is 121 dB
200 feet (61 m) the sound level is 111 dB
400 feet (122 m) the sound level is 101 dB
FEMA studies indicate typical ambient sound levels vary by location as follows:
• Industrial Areas: 70+ dBC
• Urban Areas: 60 dBC
• Rural Areas: 50 dBC

13
Installation
Description, Specications, Installation, and Service Manual
Assuming a typical 10 dB loss per distance doubled and a 70 dB minimum sound
level required to warn a typical urban area, the effective range of a MOD6024B is
approximately 3,900 feet.
Optimum warning is obtained when the warning signal is at least 10 dB above ambient.
Do not expose personnel to sound levels above 123 dBC.
Wind speed and direction often affects the propagation of sound from the siren.
Consequently, the direction of the prevailing wind may be a signicant factor to consider
when selecting the installation site(s) of a small, one- or two-site siren system. For
example, if the prevailing wind is from the west, it may be desirable to install the siren
toward the western edge of the area to be covered.
Other factors to consider when selecting the installation site(s) include the availability
of suitable electrical power, the access to and ease of installation and maintenance, the
height of surrounding obstructions, and security against vandalism and any applicable
state or local noise control ordinance.
Installing the Sirens
Electrocution or severe personal injury can occur when making electrical
connections, drilling holes, or lifting equipment. Therefore, experienced
electricians, in accordance with national and local electrical codes, acting
under the direction of the installation crew safety foreman, should perform
installation.
Most siren installations are one of two types: Pole Mount or Flat Surface Mount. These
two congurations make it possible to install a siren in almost any situation. If the
installations in this section are not suitable, modication of one of the congurations may
be practical.
A siren is typically installed 40 to 50 feet above the ground. If the installation is located
less than 40 feet above the ground, the sound intensity at close range may increase, but at
the same time the effective range of the siren may be reduced. Conversely, if the siren is
located more than 50 feet above ground, the effective range of the siren may increase, but
the sound may skip over areas closer to the siren. These variables may make it desirable
to test the sound coverage of the siren at various heights and locations whenever possible.
NOTE: To protect the speaker arrays from damage during shipping, all models have been
shipped without drivers installed.
Connecting the Driver Wires
After uncrating the siren, connect the driver wires:
1. Remove the four (4) driver access doors from each individual active module by
removing the four (4) bolt and washer sets of each door. Note the position of the at
washer and lock washer.
2. Thread the drivers clockwise onto the horn throats.

14
Installation
Modulator High-Powered Omni Speaker (MOD Series)
3. Hand tighten approximately a half turn after gasket engagement.
4. Locate the two (2) wires tie wrapped near the end of the horn throat. Note the label
on the back of the drivers and connect the solid wire to terminal 1 and the striped
wire to terminal 2 and white jumpers from 1 to 2 as shown in “Figure 6 Driver
Connections” on page 19.
Connecting driver wires out of phase may cause severe reduction in sound
output.
Wooden Pole Mounting
A typical wooden pole-mounted siren installation is shown in Figure 3. The siren
is mounted on a Class 2 utility pole (ANSI type wooden pole or equivalent) with a
minimum horizontal ground stress rating of 3,700 pounds (1678 kg). Ensure that soil
loads will conform to this size utility pole. It is attached to the pole by means of legs, as
shown in Figure 2.
Figure 2 Siren Leg Assembly
1/2-13 HEX NUTS (8)
SPLIT LOCKWASHERS (8)
1/2-13 HEX HD. BOLTS (8)
LEGS (4)
MODULATOR SIREN
BASE PLATE
LEGS (4)
SEE DETAIL
BELOW
291274A
RUBBER
INSULATOR
8570081

15
Installation
Description, Specications, Installation, and Service Manual
Figure 3 Typical Wooden Pole-mounted Installation
REFER TO
REFER TO
CONTRACT
SPECS.
CONTRACT SPEC.
(CUSTOMER SUPPLIED)
GROUND LEVEL
CONCRETE FOOTING OPTIONAL
CONTRACT SPECIFICATIONS DETERMINE
AND NATIONAL ELECTRICAL BUILDING CODES
BEFORE PROCEEDING WITH INSTALLATION.
INSTALLATION ALWAYS REFER TO LOCAL
NOTE: DRAWING DEPICTS A TYPICAL
NOTE: CERTAIN SOIL CONDITIONS MAY
REQUIRE GUYING FOR THE POLE.
CLASS II UTILITY POLE
(CUSTOMER SUPPLIED)
(CUSTOMER SUPPLIED)
GROUND ROD TO BE 8 FT.
#4 COPPER WITH CLAMP
1-1/4" CRANE LIFT HOLE
(CONTROL UNIT & BATTERY BOX)
ULTRAVOICE CONTROL
CONTROL UNIT GROUND WIRE
BATTERY BOX
SERVICE DISCONNECT
BETWEEN ANGLE LEGS & POLE.
(CUSTOMER SUPPLIED)
(CUSTOMER SUPPLIED)
(IF REQUIRED)
INSTALL 5/8" LAG BOLTS & SHIMS
(CUSTOMER SUPPLIED) AS REQUIRED
SPEAKER ASSEMBLY GROUND
WIRE, #4 COPPER, CONNECT
RADIO ANTENNA (IF REQ'D)
TO GROUND ROD DIRECTLY.
CONDUIT & CLAMPS
(CUSTOMER SUPPLIED)
40' SPEAKER CABLE (LONGER OPTIONAL)
(FEDERAL SUPPLIED)
CRANE LIFT EYEBOLT
100W DRIVER (4 PER ACTIVE CELL)
(SHOWN POLE MOUNTED)
MOD6024
DRIVER ACCESS DOOR
291275B

16
Installation
Modulator High-Powered Omni Speaker (MOD Series)
To mount the siren on the Class 2 utility pole using the three-foot-long angle iron legs:
1. Uncrate the siren and remove the nuts that hold the siren on the shipping base. Install
drivers if needed. Lift the siren approximately 3-1/2 feet with a crane or hoist.
NOTE: To protect the speaker arrays from damage during shipping, all models have
been shipped without drivers installed.
2. If you ordered optional top and side lights, see “Installing Lights on the Siren” on
page 21. You may want to install lights prior to placing onto pole.
3. Install the four legs on the siren mounting plate, as shown in “Figure 2 Siren Leg
Assembly” on page 14. Use two stainless steel 1/2-inch bolts, nuts and lock
washers (provided) for each leg. All mounting hardware needed is supplied in the
hardware kit shipped with this manual. Do not tighten the bolts completely.
The eyebolt does NOT have sufcient strength to support the combined weight
of the siren and a utility pole. Therefore, do NOT attempt to erect the pole and
siren together using the eyebolt as a lifting point.
4. Erect the utility pole in accordance with accepted practices and FEMA guidelines
(refer to warning). Be sure the pole extends at least 40 feet above the ground.
5. Raise the siren to the necessary height and lower it over the pole. Maintain tension
on lifting chain until all bolts are tightened.
6. Adjust the legs and insert shims, if necessary, between the siren legs and pole. Bolt
the siren to the pole using two user supplied 5/8-inch lag bolts, at least 4 inches long
for each leg. Tighten all bolts, including those from step 2.
Steel Pole Mounting
In a typical steel pole-mounted siren installation the MOD1004BC, MOD2008BC and
MOD3012BC sirens are mounted on a Grade A Standard galvanized steel pole. The
MOD4016BC, MOD5020BC, MOD6024BC, MOD6032BC, and MOD8032BC are
mounted on a Grade A Heavy galvanized steel pole. (Ensure that soil loads will conform
to this size utility pole.)
NOTE: The siren leg assembly is not included with the steel/concrete pole models.
To mount the siren on a Grade A Standard galvanized steel pole:
1. Erect the steel utility pole in accordance with accepted practices and FEMA
guidelines.
2. Uncrate the siren. Remove and dispose of any hardware that holds the siren on the
shipping base. Install drivers (see NOTE on page 13). Lift the siren with a crane or
hoist to the necessary height and lower it over the pole. Maintain tension on lifting
chain until all bolts are tightened.
3. If you ordered optional top and side lights, see Installing Lights on the Siren. You
may want to install lights prior to placing onto poll.

17
Installation
Description, Specications, Installation, and Service Manual
NOTE: Siren cable is run through the center of the mounting plate through the steel
pole. Siren cable can be pre-assembled through center of mounting plate for a no conduit
installation.
The eyebolt does NOT have sufcient strength to support the combined
weight of the siren and a utility pole. Therefore, do NOT attempt to erect the
pole and siren together using the eyebolt as a lifting point.
Figure 4 Steel Pole Mounting
1/2-13 X 2" LG.
S.S. SCREWS
1/2" SPLIT S.S.
LOCKWASHER
1/2-13 S.S. NUT
HEAVY
NOTE:
TO AVOID GALVANIC CORROSION
INSTALL RUBBER INSULATOR 8570080
BETWEEN SIREN BASE PLATE AND
POLE BASE PLATE.
USE S.S. SHIMS BETWEEN MTG. PLATES
IF MATING SUFACES ARE NOT FLUSH
TO AVOID WELDMENT CRACKS
291349A
3. Attach the modulator base to the pole’s top plate with rubber insulator 8570080
between them.
4. Use four of the stainless steel 1/2 in bolts, nuts, and lock washers provided.
(See Figure 4.) All mounting hardware needed is supplied in the hardware kit
shipped with this manual. Not all the hardware in the kit will be used in this type
of installation. Before tightening bolts, check mounting surfaces for warping. If
modulator base and top plate of pole have a gap greater than approximately 1/16 inch
between them, install galvanized or stainless steel shims to even out. Tighten bolts to
45-46 ft-lb torque.

18
Installation
Modulator High-Powered Omni Speaker (MOD Series)
Figure 5 Siren Base Plate
291277A
3.49
9.00
3.49
3.49
2.39
18.00
90°
4X 1.62
4X 45°
4X 2.47
4X 4.94
2.39
9.00
6.233.49
18.00
6.23
Ø23.25
20X Ø0.56
Flat Surface Mounting
This installation conguration is practical when the installation site is on a at roofed
building. A weight distribution mat is often required to safely distribute the siren’s weight
on the roof. A Structural Engineer is required.
Driver Connections
Depending on the model of siren used, the number of driver connections and wire colors
will vary. This is due to the different number of drivers required for each model. See
Figures 6 and 7 for wiring and position.
Observe proper polarity when making these connections:
• The striped wire is common and goes to position 2.
• The solid colored wire is signal high and goes to position 1.
NOTE: Drivers on all Modulators except MOD1004 and MOD2008 are not assembled
due to shipping orientation.
The bottom module in the speaker array is an inactive module. This means there are
no drivers contained in the module. The next module up is called module number one.
The next one above module one is called module number two, and so forth. These are
referred to as active modules. Each active module contains four (4) drivers except the
MOD6032B has two modules with eight (8) drivers.

19
Installation
Description, Specications, Installation, and Service Manual
Figure 6 Driver Connections
FIRST ACTIVE MODULE DRIVER ORIENTATION
TOP VIEW
291347
BRN
BRN
WHT\BRN
WHT JUMP
WHT JUMP
WHT\BRN
JUMPER
WIRE
WHT/BRN
BRN
SPEAKER CABLE
BLK
PNK
RED/WHT
RED/BLK
BRN
WHT
WHT/BRN
WHT
1
2
3
4
5
6
ACTIVE
MODULE
7
DRIVER -
TERMINAL
A2 - 2
A4 - 1
DRIVER -
TERMINAL
A3 - 2
A1 - 1
A1 - 2 A2 - 1
---
--- A3 - 1 A4 - 2
--- --- ---
--- --- ---
WHT/RED
RED RED
WHT
WHT/RED
WHT
B2 - 2
B4 - 1
B3 - 2
B1 - 1
B1 - 2 B2 - 1
---
--- B3 - 1 B4 - 2
WHT/VIO
VIO VIO
WHT
WHT/VIO
WHT
G2 - 2
G4 - 1
G3 - 2
G1 - 1
G1 - 2 G2 - 1
---
--- G3 - 1 G4 - 2
WHT/GRY
GRY GRY
WHT
WHT/GRY
WHT
H2 - 2
H4 - 1
H3 - 2
H1 - 1
H1 - 2 H2 - 1
---
--- H3 - 1 H4 - 2
--- --- ---
--- --- ---
LIGHT
BOTTOM MOUNT +
BOTTOM MOUNT -
---
TOP MOUNT +
TOP MOUNT -
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
WHT/ORG
ORG ORG
WHT
WHT/ORG
WHT
C2 - 2
C4 - 1
C3 - 2
C1 - 1
C1 - 2 C2 - 1
---
--- C3 - 1 C4 - 2
WHT/YEL
YEL YEL
WHT
WHT/YEL
WHT
D2 - 2
D4 - 1
D3 - 2
D1 - 1
D1 - 2 D2 - 1
---
--- D3 - 1 D4 - 2
WHT/GRN
GRN GRN
WHT
WHT/GRN
WHT
E2 - 2
E4 - 1
E3 - 2
E1 - 1
E1 - 2 E2 - 1
---
--- E3 - 1 E4 - 2
WHT/BLU
BLU BLU
WHT
WHT/BLU
WHT
F2 - 2
F4 - 1
F3 - 2
F1 - 1
F1 - 2 F2 - 1
---
--- F3 - 1 F4 - 2
8
1 2
A4
A3
1 2
1
A2
2
1
A1
2
For the standard cable length supplied with the siren see Table 13. The number of
conductors and colors vary from module to module. For example, in a MOD5020B, there
are 16 wires with only 10 of those being used for driver connections. Note that each cable
has four spare wires used for top or side light connections.
Table 13 Number of Wires and Cable Length per Module
Module Number of wire and how wires are used Cable Length
MOD1004B/MOD1004BC 8 wires: 2 are used for driver connections,
4 are reserved for top or side lights
44 ft
MOD2008B/MOD2008BC 8 wires: 4 are used for driver connections,
4 are reserved for top or side lights
44 ft
MOD3012B/MOD3012BC 16 wires: 6 are used for driver connections,
4 are reserved for top or side lights
42.5 ft
MOD4016B/MOD4016BC 16 wires: 8 are used for driver connections,
4 are reserved for top or side lights
42.5 ft
MOD5020B/MOD5020B 16 wires: 10 are used for driver connections,
4 are reserved for top or side lights
42.5 ft
MOD6024B/MOD6024BC 16 wires: 12 are used for driver connections,
4 are reserved for top or side lights
42.5 ft
MOD8032B/MOD8032BC
MOD6032B/MOD6032BC
20 wires: 16 are used for driver connections,
4 are reserved for top or side lights
44 ft

20
Installation
Modulator High-Powered Omni Speaker (MOD Series)
Figure 7 MOD6032B Driver Connections
BRN
BRN
WHT\BRN
WHT JUMP
WHT JUMP
1 2
A4
A3
1 2
1
A2
2
1
A1
2
WHT\BRN
ACTIVE MODULE DRIVERS 1, 2, 5 & 6 ORIENTATION
TOP VIEW
ACTIVE MODULE DRIVERS 3 & 4 ORIENTATION
TOP VIEW
1 2
D3
1 2
D4
1 2
C3
12
C4
12
C1
1 2
C2
12
D1
12
D2
YEL
YEL
ORG
ORG
WHT/YEL
WHT/YEL
WHT/ORG
WHT/ORG
JUMPER
WIRE
WHT/BRN
BRN
ORG
SPEAKER CABLE
BLK
PNK
RED/WHT
RED/BLK
BRN
WHT
WHT/BRN
WHT
ORG
1
2
3
4
5
6
ACTIVE
MODULE DRIVER -
TERMINAL
A2 - 2
A4 - 1
C1 - 1
DRIVER -
TERMINAL
A3 - 2
A1 - 1
A1 - 2 A2 - 1
---
--- A3 - 1 A4 - 2
--- --- ---
--- --- ---
WHT/RED
RED RED
WHT
WHT/RED
WHT
B2 - 2
B4 - 1
B3 - 2
B1 - 1
B1 - 2 B2 - 1
---
--- B3 - 1 B4 - 2
C3 - 1
--- WHTC1 - 2 C2 - 1
WHT/ORG C2 - 2 C4 - 2WHT/ORG
--- WHTC3 - 2 C4 - 1
YEL D1 - 1
D3 - 1
WHT/YEL D2 - 2D4 - 2
WHT
D3 - 2 D4 - 1
YEL
---
WHT/YEL
--- WHT
D1 - 2 D2 - 1
GRN GRN
E1 - 1 E3 - 1
--- WHT
E1 - 2 E2 - 1
WHT/GRN E2 - 2 E4 - 2 WHT/GRN
--- WHT
E3 - 2 E4 - 1
BLU F1 - 1
F3 - 1
WHT/BLU F2 - 2F4 - 2
WHT
F3 - 2 F4 - 1
BLU
---
WHT/BLU
--- WHT
F1 - 2 F2 - 1
WHT/VIO
VIO VIO
WHT
WHT/VIO
WHT
G2 - 2
G4 - 1
G3 - 2
G1 - 1
G1 - 2 G2 - 1
---
--- G3 - 1 G4 - 2
WHT/GRY
GRY GRY
WHT
WHT/GRY
WHT
H2 - 2
H4 - 1
H3 - 2
H1 - 1
H1 - 2 H2 - 1
---
--- H3 - 1 H4 - 2
--- --- ---
--- --- ---
LIGHT
BOTTOM MOUNT +
BOTTOM MOUNT -
---
TOP MOUNT +
TOP MOUNT -
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---