Feig Electronic OBID i-scan ID ISC.PRH102-B User manual

INSTALLATION
final
public (B)
2010-06-29
M91101-0e-ID-B.doc
OBI
D
i-scan
®
ID ISC.PRH102-B

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 2 of 18 M91101-0e-ID-B.doc
Note
©Copyright 2009-2010 by
FEIG ELECTRONIC GmbH
Lange Strasse 4
D-35781 Weilburg
Tel.: [phone]
http://www.feig.de
With the edition of this document, all previous editions become void. Indications made in this manual may be
changed without previous notice.
Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden
without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the
grant of a patent or the registration of a utility model or design.
Composition of the information in this document has been done to the best of our knowledge. FEIG
ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this
manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,
despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC
GmbH does not give any guarantee promise for perfect function in cross environments and does not give
any guaranty for the functionality of the complete system which incorporates the subject of this document.
FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed
with components and testing methods for a level of reliability suitable for use in or in connection with surgical
implants or as critical components in any life support systems whose failure to perform can reasonably be
expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application
designer must take reasonably prudent steps to protect against system failures.
FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu-
ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does
not convey any license under its patent rights nor the rights of others.
OBID®and OBID i-scan®are registered trademarks of FEIG ELECTRONIC GmbH.
my-d®is a registered trademark of Infineon Technologies AG
I-CODE®is a registered trademark of Philips Electronics N.V.
Tag-itTM is a registered trademark of Texas Instruments Incorporated.
BluetoothTM is a registered trademark of Bluetooth SIG Inc.

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 3 of 18 M91101-0e-ID-B.doc
Contents
1. Safety Instructions / Warning - Read before start-up ! 4
2. Performance Features of the ID ISC.PRH102 5
2.1. Performance features .........................................................................................................5
2.2. Available Reader-Types......................................................................................................5
3. Control and Display Elements 6
3.1. Signal buzzer.......................................................................................................................6
3.2. Scan - button .......................................................................................................................6
3.3. LED.......................................................................................................................................7
4. Assembly and Wiring 8
4.1. Reader with Bluetooth™ interface ID ISC.PRH102-B.......................................................8
4.1.1. Bluetooth™(BT) interface..............................................................................................8
4.1.2. Supply voltage...............................................................................................................9
4.1.3. Charging the batteries .................................................................................................10
4.1.4. Reset - button ID ISC.PRH102-B ................................................................................11
5. Technical Data 13
6. Approvals 15
6.1. Europe (CE).......................................................................................................................15
6.2. Declaration of Conformity................................................................................................16
6.3. USA and Canada (FCC and IC).........................................................................................17
7. Appendix 18
7.1. Accessories.......................................................................................................................18
7.2. Scope of delivery...............................................................................................................18

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 4 of 18 M91101-0e-ID-B.doc
1. Safety Instructions / Warning - Read before start-up !
•The device may only be used for the intended purpose designed by for the manufacturer.
•When installing the device in areas covered under FCC 47 CFR Part 15 a minimum separation
of 20 cm (8 inch) between antenna and the human body must be maintained.
•The operation manual should be conveniently kept available at all times for each user.
•Unauthorized changes and the use of spare parts and additional devices which have not been
sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such
unauthorized measures shall exclude any liability by the manufacturer.
•The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid
for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,
or omissions in the manual or automatically set parameters for a device or for an incorrect
application of a device.
•Repairs may only be executed by the manufacturer.
•Installation, operation, and maintenance procedures should only be carried out by qualified
personnel.
•Use of the device and its installation must be in accordance with national legal requirements
and local electrical codes .
•When working on devices the valid safety regulations must be observed.
•Special advice for carriers of cardiac pacemakers:
Although this device doesn't exceed the valid limits for electromagnetic fields you should keep
a minimum distance of 25 cm (10 inch) between the device and your cardiac pacemaker.

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 5 of 18 M91101-0e-ID-B.doc
2. Performance Features of the ID ISC.PRH102
2.1. Performance features
The ID ISC.PRH102 are devices for contactless data exchange with common Transponder ac-
cording ISO 15693. The readers have an internal antenna and will be delivered ready for connec-
tion. The device is designed as a handheld.
An anti-collision function enables simultaneous reading of several transponders per second.
The Reader electronic is fitted in a plastic housing with a protection class IP30.
The Reader ID ISC.PRH102-B has an Bluetooth interface
2.2. Available Reader-Types
Following Reader-Types are available at present:
Reader-Types Description
ID ISC.PRH102-B Bluetooth interface with internal antenna and
voltage supply by means of 4 rechargeable Mignon AA batteries
Table 1: Reader-Types

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 6 of 18 M91101-0e-ID-B.doc
3. Control and Display Elements
LED
Scan-button
Fig. 1: Control and Display Elements
3.1. Signal buzzer
The signal buzzer can be configured by the software.
In the standard configuration the signal buzzer will be active if a Transponder is recognised.
3.2. Scan - button
The switch of the reader can be configured by the software.
In the standard configuration the serial number of the Transponder is read and is sent to the host
after pressing the scan - button.

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 7 of 18 M91101-0e-ID-B.doc
3.3. LED
The Reader’s LED can be configured through software.
Abbreviation Description
LED green "RUN "
-Turns on when the Reader is ready.
-Flashes during Bluetooth initialization and connection estab-
lishment.
LED blue „TRANSPONDER“
-Turns on when a Transponder is detected.
LED red „WARNING“
-Signals a warning
-Turns on if battery voltage is flat
(no more scanning possible)
LED orange „INITIALIZING “ and „WARNING“
-Flashes during Reader initialization after power-up.
-Turns on if battery voltage is too low
(rechargeable battery must be charged)
LED violet
(red & blue) „INITIALIZING internal Bluetooth interface“
- Turns on during writing bluetooth parameters in internal
bluetooth interface.
Table 2: Standard configuration of the LEDs

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 8 of 18 M91101-0e-ID-B.doc
4. Assembly and Wiring
4.1. Reader with Bluetooth™ interface ID ISC.PRH102-B
The Reader has a Bluetooth port. The supply voltage is provided only by rechargeable batteries.
The Reader is activated using the Scan button. This opens a Bluetooth connection automatically
within approx. 3 seconds. The Reader is now ready to use. After releasing the button, the Reader
remains active for several minutes. During this time the Bluetooth connection remains open.
Pressing the button again immediately starts a Scan.
4.1.1. Bluetooth™(BT) interface
Communication to the Reader is through a Bluetooth connection. Bluetooth is a short-distance
wireless RF connection which enables permanent wireless communications connections between
portable and desktop or peripheral devices. Each Bluetooth device has a unique address and can
be optionally identified with a self-explanatory name. Password protection is used for security of a
Bluetooth connection, with the Bluetooth partner being added to a confidential list. SPP (Serial Port
Profile) is used.
Initial setup of a “paired connection“ to the Reader is done by the host. After initial setup the
establishment of the bluetooth connection happens automatically by pressing the Scan button. To
establish a connection to another Bluetooth-Dongle you must first clear the existing “paired
connection” entry in the bluetooth interface of the reader (see 4.1.4. Reset - button
ID ISC.PRH102-B).
All Readers have a factory set name and a preset password. The name "OBID_PRH102B"
consists of a fixed (OBID_PRH) and a user modifiable (102B) part.
Description Default setting
Name variable 102B
Password 1234
Table 3: Standard configuration of the Bluetooth Interface
Note:
Until FECOM.DLL version 2.8.8 the COM-Port setting “Char Timeout Multiplier” from PC or
Notebook should be increased to 9-10 if a Bluetooth reader is used.

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 9 of 18 M91101-0e-ID-B.doc
4.1.2. Supply voltage
The Reader is powered by rechargeable batteries. Four AA type rechargeable batteries are used.
These are inserted into the handle of the Reader. To change the batteries, remove the battery
cover. After unlatching the springs the cover can be removed. The rechargeable batteries are
placed in the compartment according to the + and – symbols indicated (note polarity). Then
replace the cover and listen for the spring to audibly latch.
General type Europe USA Size (D*l)
Mignon R6 / UM-3 AA 15mm * 51mm
Table 4: Designations for rechargeable Mignon-type batteries
Notes:
•Use only Nickel/Cadmium (NiCd) or Nickel/Metal Hydride (NiMH) batteries.
•Do not use single-use batteries (e.g. zinc-carbon / alkaline) batteries.
•Reversed polarity may destroy the device.
•Rechargeable batteries should never be discarded with normal trash; please return them
to a proper collection location !
Fig. 2: Inserting the rechargeable batteries

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 10 of 18 M91101-0e-ID-B.doc
4.1.3. Charging the batteries
DC-Plug
Reset -
button
Minus (outside)
Plus (inside)
Fig. 3+ 4: ID ISC.PRH102-B: Reset button and DC/ plug 2.1mm*5.5mm
The rechargeable batteries may remain in the Reader for charging. You will need an external
charger connected to the DC/ jack.
DC jack Abbreviation Description
Inside +Plus – charge voltage
Outside -Minus – charge voltage
Table 5: Charger connection
Note:
•Reversing the polarity of the charger can destroy the batteries.
•The Reader is not functional while the batteries are charging.

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 11 of 18 M91101-0e-ID-B.doc
Charger :
Use a charger suitable for the battery type specified (4-cell pack).
Feig Article No. Name
2650.000.00 ID CHA.NiMH-A
Table 6: Recommended charger
The recommended charger is designed for nickel/cadmium (NiCd) type rechargeable batteries and
nickel/metal hydride (NiMH) with a capacity range of 800mAh to 7200 mAh.
Alternately the batteries can be removed from the Reader and charged in a separate battery
charger.
4.1.4. Reset - button ID ISC.PRH102-B
The Reader has a reset button. Below the yellow Scan button is a small hole in the housing. Below
this is the Reset button. On the one hand you can restore the Bluetooth settings to their original
configuration on the other hand you can clear a existing “paired connection” entry.
1. Reset Bluetooth parameters of the reader to its factory settings
After activating the Reader with the Scan button the Reader is reset to its factory settings by
holding the Reset button and the Scan button down for longer than 4 seconds until the violet LED
light up.
2. Clear “paired connection” entry in internal bluetooth interface
After activating the Reader with the Scan button the “paired connection” entry in Bluetooth
interface is cleared by holding the Reset button down for longer than 4 seconds until the violet LED
light up.

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 12 of 18 M91101-0e-ID-B.doc
Scan - button
Reset - button
Reader ON
OFF
Scan
Button ON
OFF
Reset
Button ON
OFF
Clear
“paired connection”
Longer than 4 sec
Reader
activation
Reader ON
OFF
Scan
Button ON
OFF
Reset
Button ON
OFF
Reset
“Bluetooth parameters”
Longer than 4 sec
Longer than 4 sec
Reader
activation
LED
Status
LED
Status

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 13 of 18 M91101-0e-ID-B.doc
5. Technical Data
Mechanical Data
•Housing ABS plastic (enclosed)
•Dimensions ( W x H x D ) 230 x 100 x 80 mm (9,06 x 3,94 x 3,15 inch)
•Weight 320 g
•Degree of Protection IP 30
•Color similar RAL 9002
Electrical Data
•Supply Voltage 4 Mignon AA rechargeable batteries
•Current Draw max. 0,5 A
•Power Consumption max. 2,5 VA
•Operating Frequency 13,56 MHz
•Transmitting Power 200mW ± 1dB
•Antenna internal antenna
•Interface Bluetooth (Serial port profile)

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 14 of 18 M91101-0e-ID-B.doc
Functional Properties
•Protocol Modes - FEIG ISO HOST
- Scan Mode
•Supported Transponders •ISO15693, ISO18000-3-Mode1
(EM HF ISO Chips, Fujitsu HF ISO Chips,
KSW Sensor Chips, Infineon my-d, NXP I-
Code, STM LRI ISO Chips, TI Tag-it)
•Address setting for interface Bluetooth MAC address
•Indicators
– optical
– acoustical 1 LED ( multicolor – red / green / blue)
buzzer
Ambient Conditions
•Temperature range
– Operation
– Storage 0 °C to +50 °C (32 °F to 122 °F)
-20 °C to +70 °C (-4 °F to 158 °F)
•Humidity 5 – 95% non condensing
Applicable Norms
•Radio approval
– Europe
– USA
– Canada
EN 300 330
FCC 47 CFR Part 15
IC RSS-GEN, RSS-210
•EMC ETSI EN 301 489
•Safety
- low voltage
- Human Exposure EN 60950
EN 50364
•Fall Withstands multiple 5´/1,5 m drops to concrete

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 15 of 18 M91101-0e-ID-B.doc
6. Approvals
6.1. Europe (CE)
When used according to regulation, this radio equipment conforms with the basic requirements of
Article 3 and the other relevant provisions of the R&TTE Guideline 1999/5/EC dated March 99.
Equipment Classification according to ETSI EN 301 489: Class 2

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 16 of 18 M91101-0e-ID-B.doc
6.2. Declaration of Conformity

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 17 of 18 M91101-0e-ID-B.doc
6.3. USA and Canada (FCC and IC)
FCC ID: PJMPRH102
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
NOTICE:
Changes or modifications made to this equipment not expressly approved by
FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.

OBIDi-scan® Installation ID ISC.PRH102
FEIG ELECTRONIC GmbH Page 18 of 18 M91101-0e-ID-B.doc
7. Appendix
7.1. Accessories
The following accessories are available for the Reader.
Feig Article No. Name Description
2650.000.00 ID CHA.NiMH-A Battery charger with suitable connector
for ID ISC.PRH102-B
Table 7: Accessories
7.2. Scope of delivery
Reader Scope of delivery
ID ISC.PRH102-B - Reader ID ISC.PRH102-B
- Quick user guide
Table 8: Scope of delivery
Note:
Rechargeable batteries and battery charger are not included in delivery