Fellowes Jupiter 125 User manual

http://www.monomachines.com
Please read these instructions before use.
lire ces instructions avant utilisation.
lea estas instrucciones antes del uso.
http://www.monomachines.com

http://www.monomachines.com
ENGLISH
Opening lid to clean
laminating mechanism
Discrete carry
handles at I
Active Cooling System
Temperature controlled
release trigger for lid
CAPABILITIES
Pouch Thickness
3-7 mil
Estimated Heat-Up Time
4 Minutes
Approximate Cool-Down Time
60 Minutes
Lamination Speed
18"/Minute
Maximum Width
12.5" mm
Voltage
120V
Frequency
60 Hz
HeatGuard TechnologyTM double-walled
insulation keeps heat inside
LED Interface for
user guidance
Laminating capacity - 3-7 mil hot laminating pouches
Up to 12.5"
1000 Watt
Dimensions: 21 7/8" x9 Sja" x4 3f4"
Max document thickness 1/32"
IMPORTANT SAFETY INSTRUCTIONS - Please Read Before Using!
I AWARNINGI
• The socket-outlet must be installed near the equipment
and be easily accessible.
• To prevent electrical shock, do NOT use laminator close to water ("i;\
and do NOT spill water on laminator, electric cord, or wall socket. ~
• Do not leave electric cord in contact with a warm surface.
• Do not leave electric cord hanging from a cupboard or shelf.
• Do not use laminator if electric cord is damaged.
• Do not laminate metal objects.
IMPORTANT SAFETY INFORMATION
This laminator is equipped with an Auto shut-off function. It will turn the laminator into
stand-by mode, if it has not been used for over 60 minutes. To switch the laminator
back on, simply press the stand-by button at the left of the front operating panel.
I ACAUTIONI
• Only use pouches specifically designed for the lamination setting you intend to use.
• Always supervise children during laminator operation.
• Keep pets away from laminator while in use.
• Switch off and unplug laminator when not in use.
• Only open the laminator as explained under "Maintenance". Do not open or
attempt to repair in any other way, as this could result in electric shock and will
void your warranty. Contact Customer Service if you have questions. Please note
the warranty does not apply in cases of abuse, mishandling or unauthorized repair.
• Please be careful of sharp edges and corners and residual heat when opening
the laminator.
During lamination, the direction of the pouch can be reversed, if you are unsure about
the progress of the lamination. To do so, press down the reverse key. This will eject
the pauch back at the front entry.
http://www.monomachines.com
2

http://www.monomachines.com
TIPS
• Always put item in a pouch. Never laminate an empty pouch.
• Trim excess pouch material from around your item after laminating
and cooling.
• Clean laminator rollers with Fellowes roller wipes (item #5703702) after
15-20 laminations to guarantee optimum laminating results. For further
details, please see "maintenance" section.
BEFORE YOU LAMINATE
Use Fellowes® brand pouches
for best results. Select correct
pouch size for laminated item.
COLD LAMINATION STEPS
CAUTION: Only use self-adhesive pouches when laminating with a cold setting.
1. Please connect the laminator to
the socket using the separate power
cable supplied.
2. Switch laminator on with
Power On / Off button at back
of machine.
5. Confirm your selection by
pressing "Enter" button in the middle
of navigation keys. "Wait" LED
(~) will stop flashing and beep will
sound when laminator has finished
temperature adjustment.
6
6. Center item on clear side against
sealed edge; documents cannot be
repositioned once laminated.
• Before laminating valuable items, do a test run with an item similar
in size and thickness.
• Do not laminate heat-sensitive documents (Le., tickets, ultrasounds, etc.).
• Use a dry-erase marker for writing on laminated pouches.
Position laminator
so you have enough
space to allow
items to pass freely
through the machine.
3. Press Stand-by button at left
of front operating panel to switch
laminator on.
4. Use navigation keys to select
setting for cold lamination.
7. Peel a small part of the protective
sheet away from document.
8. When the "wait" LED (~) stops
flashing, place pouch, sealed edge
first, into laminator entry. Keep
pouch straight and use the edge
guide to center it. Continue peeling
the protective sheet away.
http://www.monomachines.com
3

http://www.monomachines.com
ENGLISH
HOT LAMINATION STEPS
1. Please connect the laminator to the
socket using the separate power cable
supplied.
2. Switch laminator on with Power On /
Off button at back of machine.
4. Use navigation keys to select setting for
the hot lamination pouch thickness (3-7
mil) you wish to laminate.
7. "Wait" LED (~) will stop flashing
and acoustic bleep signal will sound when
machine is ready to laminate selected pouch
thickness.
10
5. Confirm your selection by pressing "Enter"
button in the middle of navigation keys.
"Wait" LED (0 will begin flashing and
laminator will take a few minutes to reach
required temperature.
8. Place pouch, sealed edge first, into
laminator entry. Keep pouch straight and
use the edge guide to center it.
3. Press Stand-by button at left of front
operating panel to switch laminator on.
6
6. While laminator is warming up, please
prepare item you wish to laminate. Place the
item inside the pouch and center it against the
sealed edge of the pouch. To prevent jamming,
use a carrier sheet when item is smaller than
the pouch.
9
9. To prevent jamming, immediately remove
laminated item from beck of machine. Let
item coolon flat surface for several seconds.
10. Before switching off laminator, feed
empty cleaning sheet through machine to
clean unit.
http://www.monomachines.com
4
I
I

http://www.monomachines.com
I
MAINTENANCE - Unique Easi-A((ess technology
This laminator is equipped with the unique Easi-Access technology for easy maintenance. This allows the user to open the laminator for maintenance, just like a photocopier.
1. To open the laminator, please press
2.lf machine is hot, fan will turn on to cool 3. The "Wait" LED will turn off and the
the
"Open" (-t) button as shown in the machine down to safe handling temperature ready beep will sound when machine is
the illustration. The red Open light will inside. During this time the "Wait" symbol ready to be opened.
4. Press the silver buttons on both sides of
the machine to activate the Easi-Access (The
laminator needs to be switched on to allow
illuminate.
5
will f~sh and cover will remain locked.
the active rature control to
5. Open the lid with both hands.
You are now able to clean the inside of
the laminator and carefully remove any
residual glue or other items.
When laminator is opened, power to
internal parts is isolated, so that user is
not in danger of electric shock.
TROUBLESHOOTING
6. For further maintenance, the rollers
can be released by experienced users.
Press cam levers to release the rollers.
7. To clean residue off laminator rollers,
please only use Fellowes Laminating
Roller wipes (item No 5703702) as
8. Please remember to re-secure the
rollers before closing cover to ensure
safe operation.
explained in their product instructions.
Problem
Ready light does not go on after extended time
Pouch did not completely adhere to item
Jamming
Need Help?
PI.us. ,oil our experk 01
(uslomer Service_ You'll find
the numbers for your nearest
Service Centre on the
bo,k cover of Ihis bookl.t.
LIMITED WARRANTY
Cause
Laminator is in a hot, humid area.
Laminated item may be too thick.
No item in pouch
Manually cut out pouch used
Pouch was not used.
Pouch was not centred or straight when fed
through Pouch/Document Entry.
Glue and residue left on laminating rollers.
Solution
Move laminator to a cool dry area.
Pass through laminator a second time.
All our laminators have been designed to operate jam-free. In the unlikely
event of a jam occurring, please press the 'open" ( .... ) button and wait
for the wait (~) light to stop flashing.
The laminator can be opened to remove incorrectly inserted items
as described under maintenance. Please ensure tnat you follow the
described steps.
Gently pullan the jammed material to release it.
Always put item in a pouch.
Align sealed edge with Pouch/Document Entry. Use guide
on machine to centre.
Clean residues off rollers using Fellowes Laminating Roller wipes, see
"maintenance" section.
Make sure that not residue is left on the rollers and use
cleaning sheet before laminating.
Fellowes warrants all ports of the laminator to be free of defects in material and workmanship for 2 years
from the dote of purchase by the original consumer. If an y port is found to be defective during the warranty
period, y our sale and exclusive remedy will be repair or replacement, at Fellowes' option and expense, of
the defecti ve port. This warranty does not appl y in cases of abuse, mishandling or unauthorized repair. ANY
IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED IN DURATION
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. IN NO EVENT SHALL FELLOWES BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DA MA GES ATTRIBUT A BLE TO THIS PRODUCT. This warrant y
gives y ou specific legal rights. You ma y have other legal rights that var y from this warranty. The duration,
terms and conditions of this warranty are valid world-wide, except where different limitations, restrictions or
conditions may be required by local law. For more details or to obtain services under this warranty, please
contact us or your dealer.
s
http://www.monomachines.com

http://www.monomachines.com
Help Line
Australia
+ 1-800-33-11-77
Canada +
1-800-665-4339
Europe 00-800-1810-1810
Fellowes
Australia
+ 61-3-8336-9700
Benelux
+ 31-[01-76-523-2090
Canada + 1-905-475-6320
Deutschland
+ 49-[01-5131-49770
Espana + 34-91-748-05-01
France + 33-[01-1-30-06-86-80
Italia
+ 39-071-730041
Mexico +
1-800-234-1185
United States
+ 1-800-955-0959
Japan
+ 81-[01-3-5496-2401
Korea +
82-2-3462-2884
Malaysia + 60-[01-35122-1231
Polska
+ 48-[01-22-771-47-40
Singapore
+ 65-6221-3811
United Kingdom
+ 44-[01-1302-836836
United States
+ 1-630-893-1600
http://www.monomachines.com