Fellowes 460Ms User manual

Quality Office Products Since 1917
POWERSHRED®460Ms
Please read these instructions before use.
Do not discard: keep for future reference.

A. SafeSense
®
Technology
B. CD/card entry
C. See safety instructions
D. Paper entry
E. Pull-out bin
F. Window
G. Casters
H. ON/OFF switch
1. OFF
2. ON
Will shred: Paper, credit cards, CD/DVDs and staples
Will not shred: Adhesive labels, continous form paper, transparencies, newspaper,
cardboard, laminates, paper clips, file folders, X-rays or plastic other than noted above
Paper shred size:
Micro-Cut .................................................................... 5/64 in. x 5/16 in. (2mm x 8mm)
Card/CD shred size:
Strip-Cut....................................................................................................5/16 in. (8mm)
Maximum:
Sheets per pass ........................................................................................................... 10*
Cards/CDs per pass ....................................................................................................... 1*
Paper entry width............................................................................ 8-15/16 in. (227mm)
Cards/CDs width.................................................................................. 4-7/8 in. (124mm)
*8.5 in. x11 in., 20lb., (75g) paper at 120V, 60 Hz, 5.8Amps; heavier paper, humidity or
other than rated voltage may reduce capacity. Maximum recommended daily usage rates:
400 sheets per day; 25 credit cards; 10 CDs. 10 sheets per pass to avoid jams.
Fellowes SafeSense®shredders are designed to be operated in home and office environments ranging
between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
CAPABILITIES
ENGLISH
Model 460Ms
KEY
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
15
H.
G.
A.
B.
E.
F.
D.
I.
15
• Operation,maintenance,andservicerequirementsarecoveredintheinstruction
manual. Read the entire instruction manual before operating shredders.
• Keepawayfromchildrenandpets.Keephandsawayfrompaperentry.Alwaysset
to off or unplug when not in use.
• Keepforeignobjects–gloves,jewelry,clothing,hair,etc.–awayfromshredder
openings. If object enters top opening, switch to Reverse ( ) to back out object.
• Neveruseaerosolproducts,petroleumbasedlubricantsorotherflammable
products on or near shredder. Do not use canned air on shredder.
• Donotuseifdamagedordefective.Donotdisassembleshredder.
Do not place near or over heat source or water.
• ThisshredderhasanON/OFFSwitch(H)thatmustbeintheON() position to
operate shredder. In case of emergency, move switch to OFF (O) position. This
action will stop shredder immediately.
• Avoidtouchingexposedcuttingbladesundershredderhead.
• Shreddermustbepluggedintoaproperlygroundedwalloutletorsocketofthe
voltage and amperage designated on the label. The grounded outlet or socket
must be installed near the equipment and easily accessible. Energy converters,
transformers, or extension cords should not be used with this product.
• FIREHAZARD–DoNOTshredgreetingcardswithsoundchipsorbatteries.
• Forindooruseonly.
• Unplugshredderbeforecleaningorservicing.
15
15
I. Control Panel and LEDs
1. Overheat (red)
2. SafeSense
®
indicator (yellow)
3. ON/OFF (blue)
4. Reverse
5. Forward
C.

ADVANCED PRODUCT FEATURES
Patented SafeSense®Technology
Stops shredding immediately when
hands touch the paper opening.
SilentShred™Technology
SilentShred™ noise quality
shreds without noisy disruptions.
PAPER OR CD/CARD
BASIC SHREDDING OPERATION
Continuous operation:
Up to 8-minutes maximum
NOTE: Shredder runs briefly
after each pass to clear entry.
Continuous operation beyond
8-minutes will trigger
20-minute cool down period.
SAFESENSE®TECHNOLOGY
Stops shredding immediately when hands touch the paper opening.
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
PRODUCT MAINTENANCE
TO CLEAN THE SENSORS
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry).
All micro-cut shredders require oil for peak performance. If not oiled, a
machine may experience diminished sheet capacity, intrusive noise when
shredding, and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
OILING SHREDDER
15
15
*Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
Locate Auto-start
infared sensor
Using cotton swab, wipe
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
Press and hold forward
() 2-3 seconds
*Apply oil across entry
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
Turn OFF (O) and
unplug shredder
TROUBLESHOOTING
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This
indicator will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about
the continuous operation and recovery time for this shredder.
SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate and the shredder will stop shredding.
Plug in and
turn ON (I)
1
Feed paper straight into
paper entry and release
or
Hold CD/card at edge,
feed right side of entry
and release
When finished
shredding set to
OFF (O)
234
SafeSense
®
is active and
working properly
Touch test area and
look for the SafeSense
®
indicator to illuminate
SET-UP AND TESTING
2 3
1
Turn the shredder ON
(I) to activate SafeSense
®
34
1 2 12

Quality Office Products Since 1917
©2012 Fellowes, Inc. Part No. 407323 Rev C
POWERSHRED®460Ms
LIMITED PRODUCT WARRANTY
Canada [phone]
Mexico +001-800-514-9057
United States [phone]
Questions or Concerns?
www.fellowes.com
Troubleshooting
Registration
Manuals
Customer Service & Support
Troubleshooting
Replacement parts
General questions
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of
defects in material and workmanship and provides service and support for 1 year from the date
of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to
be free from defects in material and workmanship for 7 years from the date of purchase by the
original consumer. If any part is found to be defective during the warranty period, your sole and
exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective
part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product
usage standards, shredder operation using an improper power supply (other than listed on
label), or unauthorized repair. Fellowes reserves the right to charge the consumers for any
additional costs incurred by Fellowes to provide parts or services outside of the country where the
shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable
for any consequential or incidental damages attributable to this product. This warranty gives you
specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide,
except where different limitations, restrictions, or conditions may be required by local law. For
more details or to obtain service under this warranty, please contact us or your dealer.