Fellowes POWERSHRED 3140S Service manual

Quality Office Products Since 1917
POWERSHRED
®
3140S/3140CPOWERSHRED
®
3140S/3140C
Canada [phone]
Mexico +001-800-514-9057
United States [phone]
Questions or Concerns?
www.fellowes.com
Troubleshooting
Registration
Manuals
Customer Service & Support
Troubleshooting
Replacement parts
General questions
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to
be free of defects in material and workmanship and provides service and support for
1 year from the date of purchase by the original consumer. Fellowes warrants the
cutting blades of the machine to be free from defects in material and workmanship
for 1 year from the date of purchase by the original consumer. If any part is found
to be defective during the warranty period, your sole and exclusive remedy will
be repair or replacement, at Fellowes’ option and expense, of the defective part.
This warranty does not apply in cases of abuse, mishandling, failure to comply
with product usage standards, shredder operation using an improper power supply
(other than listed on the label), or unauthorized repair. Fellowes reserves the right
to charge the consumers for any additional costs incurred by Fellowes to provide
parts or services outside of the country where the shredder is initially sold by an
authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE
APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be
liable for any consequential or incidental damages attributable to this product. This
warranty gives you specific legal rights. The duration, terms, and conditions of this
warranty are valid worldwide, except where different limitations, restrictions, or
conditions may be required by local law. For more details or to obtain service under
this warranty, please contact us or your dealer.
LIMITED PRODUCT WARRANTY
Please read these instructions before use.
Do not discard: keep for future reference.
©2015 Fellowes, Inc. Part No. 409358
Factory Service

H. Control Panel and LEDs
1. ON/OFF
R 2. Reverse
3. Bin full
4. Door open
5. Safety Flap Open
A. Safety Flap
B. Paper entry
C. Disconnect switch (open door)
D.Door
E. Basket - paper (inside)
F. Casters
G.See safety instructions
RRRR
R
R
R
R
RRRR
R
R
R
R
2
ENGLISH
Models 3140S/3140C
KEY
INDICATOR LIGHTS
Stops automatically
when door is
opened. Symbols
flash alternately
Stops automatically
when bin is full.
Empty bag when
bag full indicator
lights up
Stops automatically
if too much
paper is inserted.
Automatic reverse
if paper jams
Stops automatically
if safety flap is
opened. Symbols
flash alternately
Overload protection.
Machine stops to cool
down- approx. 10-15
minutes. Symbols
flash alternately
RRRR
R
R
R
RRRR
R
R
R
RRRR
R
R
R
RRRR
R
R
R
RRRR
R
R
R
R
Will shred: Paper, credit cards, CD/DVDs, staples, paper clips and junkmail
Will not shred: Adhesive labels, transparencies, newspaper, cardboard,
laminates, file folders, X-rays or plastic other than noted above
Paper shred size:
Strip-Cut...........................................................................1/4 in. (6mm)
Cross-Cut........................................3/16 in. x 1-1/2 in. (4mm x 40mm)
* In order to perform at capacity, shredder must be plugged into a dedicated 15Amp,
120V outlet.
Maximum:
Paper entry width................................................................16”/406mm
*8.5”x11”, 20lb., (75g) paper at 120V, 60 Hz, 11.6Amps; heavier paper,
humidity or other than rated voltage may reduce capacity.
CAPABILITIES
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
15
15
15
15
15
15
• Keep away from children and pets. Keep hands away from
paper entry. Always set to off or unplug when not in use.
• Keep foreign objects – gloves, jewelry, clothing, hair, etc. –
away from shredder openings. If object enters top opening,
switch to Reverse (R) to back out object.
• Never use aerosol products, petroleum based lubricants or
other flammable products on or near shredder. Do not use
canned air on shredder.
• Do not use if damaged or defective. Do not disassemble
shredder. Do not place near or over heat source or water.
• Operation, maintenance, and service requirements are covered
in the instruction manual. Read the entire instruction manual
before operating shredders.
• This shredder has a Disconnect Power Switch (C) that must
be in the ON (I) position to operate shredder. In case of an
emergency move switch to OFF (O) position. This action will
stop shredder immediately.
• Avoid touching exposed cutting blades under shredder head.
• Do not put foreign objects in paper entry.
• Shredder must be plugged into a properly grounded wall
outlet or socket of the voltage and amperage designated on
the label. The grounded outlet or socket must be installed
near the equipment and easily accessible. Energy converters,
transformers, or extension cords should not be used with
this product.
• FIRE HAZARD – Do NOT shred greeting cards with sound chips
or batteries.
• For indoor use only.
A .
B .
G.
H.
F.
C.
D.
E.
SHREDDER SET-UP PAPER/CARD
Ensure access
to a dedicated
15Amp, 120V
outlet
3
BASIC SET-UP BASIC SHREDDING OPERATION
Plug in and make
sure door is closed Press ( ) ON to
activate When finished
shredding set to
( ) OFF
Feed paper
straight into paper
entry and release
Do nothing and
shredder will go
automatically to
sleep mode after
1 hour
Make sure safety
flap is securely
in place
LIMPIEZA DE LOS SENSORES INFRARROJOS DE INICIO AUTOMÁTICO
Eliminates frustrating jams by preventing overloads.
SHEET CAPACITY GAUGE
PAPER JAM
SLEEP MODE
CLEANING AUTO-START INFARED SENSORS
Electronically measures paper thickness to prevent
paper jams:
RRR
R
R
R
R
Up to RED: Too many sheets have been
inserted. Automatic reverse of paper.
Up to YELLOW: Maximum sheet capacity.
Up to GREEN: Normal sheet capacity
during shredding process.
In sleep mode To get out of sleep
press ON ( )insert paper
or
WHEN IN SLEEP MODE
Set to Off ( ) and empty bin. Replace bin and follow the
below procedures.
Stops automatically
if too much paper
is inserted.
Automatic reverse
if paper jams
Gently pull uncut
paper from
paper entry.
Machine runs for
a short time in
reverse. Repeat if
necessary
Paper detection sensors are designed for maintenance free operation. However, on
rare occasions the sensors may become blocked by paper dust causing the motor to
run even if there is no paper present (Note: two paper detection sensors are located in the center
of the paper entry).
Turn off and
unplug shredder Locate Auto-start
infared sensor Clean any contamination from
the paper sensors
Use thin, long-handled
brush to clean sensors.
Make sure brush is
clean and dry
TO CLEAN THE SENSORS
R
R
3
R
R
R
RRRR
2
R
R
1
RRRR
R
R
R
R
1
1
R
R
2
R
R
3
R
R
4
R
R
R
RRRR
or
4 5
R
R
1
R
R
3
R
R
R
RRRR
2
R
R
R
R
R
R
12
2
R
R
15
15
*Only use a non-aerosol vegetable oil in long nozzle container
such as Fellowes 35250
All cross-cut shredders require oil for
peak performance. If not oiled, a
machine may experience diminished
sheet capacity, intrusive noise when
shredding and could ultimately stop
running. To avoid these problems,
we recommend you oil your shredder
each time you empty your waste bin.
OILING SHREDDER
Set to Reverse (R)
2-3 seconds
*Apply oil
across entry
Set to Off (O)
TROUBLESHOOTING and PREVENTIVE MAINTENANCE
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
RRR
R
R
R
R
1
RRR
R
R
R
R
3
R
R
2
• Empty wastebasket when bin full indicator
lights up.
• Shredder won’t run if the door is open,
or bin needs to be emptied.
• Maintenance is an important part of
protecting your investment. Don’t forget
to purchase our oil (35250) and
shredder bags (3604101).
Go to Support Section at www.fellowes.com
or see back page of manual for useful
telephone numbers.